I did it on my own risk. This is just a video on my experience. You take your own risk if you do the same.
Пікірлер: 38
@robertorobles52555 жыл бұрын
thanks man, i fixed mines using your procedure, i just re-soldered cables and used hot glue to keep 'em in place, also applied more hot glue in the remain cables to keep 'em in place too. Problem solved.
@Depaanjay Жыл бұрын
Where did u solder and and which wires ????? Please reply man
@TheRedstoneChannel14 жыл бұрын
You are a life saver! Thank you man!
@hatovsky Жыл бұрын
thanks worked for me too 😁
@TKO755 жыл бұрын
thanks. What a pain. I had to replace mine 6 times thru warranty over the last year. Same problem with yours on 3 and loose battery one the other ones keep making noise when I move my head. Really poor quality on this model.
@lawrencemburu75745 жыл бұрын
thanks man
@hewlett19204 жыл бұрын
Any idea how to maximize its volume? I tried compared my jbl duet nc to beats studio 2.0 but they differ in volume. I tested pairing on both android and iphone and put to max volume but it doesnt sound loud compared to beats. Feels like there is volume limiter
@solomonrein54405 жыл бұрын
Mine it’s giving me a headache 🤕😤, can someone help me with the clear procedures please
@gro002453 жыл бұрын
Relevant for my e65btnc’s, I bought these in a hurry and should have done some research… Sporadic crackling after nearly 2 years (always in a case and taken care of), then constantly with NC active, so this probably applies for all JBL models. Followed instructions with a twist. I drilled a new hole and used utp cable wire to replace the 2 sides of the driver, not touching the mic, added some electric tape inside to cover the hole. They work fine again now, last time I bought JBL, what s**t R&D. Next will be Sennheiser, Bose or Sony. How are those treading you?
@Depaanjay Жыл бұрын
Which cables did u replace )?
@Atrickz.3 жыл бұрын
fixed my crackling ijust needed to swap my headphones to stereo!!
@mscir4 жыл бұрын
Can you show the same procedure for the JBL EVEREST ELITE 750NC
@spoghosyan4 жыл бұрын
Nope, sorry. I am an ordinary consumer with one faulty device, not a tech.specialist
@earldesign9914 жыл бұрын
Same issue here. So, looks like I just need to pull the cushion off and then the speaker plate to get to the wires underneath. no need to mess with the back side of the ear piece.
@spoghosyan4 жыл бұрын
correct, provided there enough free cable to pull for proper soldering. In my case I had to start from the back as I did not know where the loose connection is and the first suspect was the plate and the wires connecting the plate
@spicygaming9528 Жыл бұрын
Hi bro. Did you heat the earcups a little bit before digging in with the cutter?
@spoghosyan Жыл бұрын
no, no need to heat it up in my case
@COLC235 жыл бұрын
If I wanna replace the cushions ear pads, what model should be the same or similar so I can buy them??
@X-PiAcoustic3 жыл бұрын
see my channel, I did elaboration about that
@kenyardpeacock65033 жыл бұрын
My problem came from overcharging and I didn’t keep it on the charger all the time the static went away
@rickeyl.mcspaddenii47295 жыл бұрын
Have you had any problem since the fix?
@spoghosyan5 жыл бұрын
nop. all working perfectly since then
@frankfrancisquezluquez74494 жыл бұрын
Tbh it happens to me to put I just hit the side of it lightly and it just goes back to normal
@ritacarl49274 жыл бұрын
how did you get them apart, you see them complete and then opened, I have no idea how to open mine so please help
@spoghosyan4 жыл бұрын
I dont remember now, sorry. I sold them and bought sony 1000 xm3
@gro002453 жыл бұрын
If still relevant: First you go very gently between the outer ring with something very thin, I used a small Victorinox knife and a putty knife. (zero visible damage here) The rest should be strait forward from the tutorial. The triangle screws you can take out with a flat screwdriver (F*** you JBL) Don’t try this if you’re not at least a bit familiar with electronics repair/DIY or it’s a guaranteed failure. When opening the driver housing you will always need to repair. The short wire will break no matter how gentle you are, just too short to open the case.
@X-PiAcoustic3 жыл бұрын
Just simply force to open it, it has 5 undercuts inside, just go ahead, no worry to be damaged.
@PiratPi Жыл бұрын
So i simply need to glue the wires?
@spoghosyan Жыл бұрын
not to glue. but to solder
@josebarboza48755 жыл бұрын
That happened to me too and then one of the headphones dont work😤😤😤😤
@Depaanjay Жыл бұрын
Where do we have to solter????
@spoghosyan Жыл бұрын
where the wire connects the speaker part - that was in my case. donno where it is broken in other cases
@Depaanjay Жыл бұрын
@@spoghosyan its the worst headphones i wasted 10k rupees on that bad product its in the trash now
@Depaanjay Жыл бұрын
I got it fixed by replacing the speaker
@BryanAcostaswagelishious3 жыл бұрын
Turn off the ANC i have mine off and the creak sounds goes away
@spoghosyan3 жыл бұрын
But you have paid for that function, havent you? ANC is a great function that I use often in a noisy environment