How to Paint Fill Wood that has been Laser Engraved

Рет қаралды 378,282

2 жыл бұрын

Follow the steps in this how-to video when laser engraving products like rosewood boxes, piano and particle finish plaques as well as bamboo cutting boards and red alder products. If you cannot hear the audio watch the video here: • How to Paint Fill Wood...
To browse the thousands of laserable products available from JDS Industries, visit bit.ly/3j8xNXr or call 800.843.8853 to speak with a customer service representative.
#JDSTutorials #LaserTutorial #LaserEngraving

Пікірлер: 189

@JDSINDUSTRIES 2 жыл бұрын

Hello! We are aware that some users may not be able to hear any audio when viewing this video. If you cannot hear the audio from this video, click this link to view a version with updated audio: kzfaq.info/get/bejne/e5eGpclk27Wum4k.html Sorry for the inconvenience!

@muskokamike127 Жыл бұрын

better way to remove the mask from inside the letters is to use a dental pick. It tends to not scratch the substrate or cut the masking tape.

@heyjeeery7587 2 жыл бұрын

awesome, loved the way you got to the point without going thru the basics of how to use the laser or software. great job

@davidr5964 2 жыл бұрын

So many small tips contained in this one video! The end product looks amazing too.

@johndiego3105 2 жыл бұрын

That turned out beautiful. Thanks for sharing the tips.

@Renuewspa Жыл бұрын

Excellent tutorial! Possibilities are limitless❤️

@1rtt1 Жыл бұрын

Thank you for a video on a practical method of coloring laser etching.

@jwolfjwolf6685 2 жыл бұрын

Good demo, thanks!

@DGLaserCraft 11 ай бұрын

Great video with clear instructions - thank you!

@RoadstarRider1 2 жыл бұрын

Very nice end result, well done !

@rafadominguez6577 6 ай бұрын

Thanks a lot for your easy and simple tutorial with great content

@pure.intentionzz 2 жыл бұрын

You added value to my life thank you!

@bigpapaporsche1 Жыл бұрын

Great video and technique! I've been watching "KZfaqs" videos for 3 hrs looking for a solution to my problem, WOW I think I found it! My project is to have a Compass Rose, Laser cut into a Maple Table Top which has been already stained. After painting the craving, I'll be able to apply the Top Coat of finish. By the way, I started out trying to use Epoxy Inlay but that got involved and expensive.

@Arlisa1913 2 жыл бұрын

beautiful work!

@I-LOVE-EARTH Жыл бұрын

Excellent job!

@rwoodard6984 2 жыл бұрын

An excellent instructional presentation By a lovely lady Who knows what she’s doing. Thankyou.

@stevepalmer3160 2 жыл бұрын

Thank you for sharing this

@BasteLey 2 жыл бұрын

Wow - thanks for showing

@expresspackship2359 2 жыл бұрын

I find your videos very helpful! Also, I just wanted to point out...I love your Color Street nails! :D

@ericcarabetta1161 2 жыл бұрын

Wow, I'm equally impressed by the size of that masking tape, I had no idea it came in rolls that size.

@johnmacdonald2441 2 жыл бұрын

It comes even bigger than that and it's cheap. It's called application tape - search for sign suppliers.

@Graeme758 2 жыл бұрын

It's used in the vinyl signwriting trade, google transfer or liftoff tape.

@jimhatch5873 2 жыл бұрын

It's called Vinyl Transfer Tape or Mask. But it's not vinyl (bad for your laser) but actually a paper based masking that is used for vinyl cutouts like lettering and such. Then the vinyl letters can be affixed to a glass door for example, the tape or masking peeled off and the vinyl remains on the door. You've probably seen it on commercial establishments. The paper based version comes in a couple of handy widths - 12" & 6" are the two I use most. The length of the rolls vary, but be careful because the cost per foot for the shorter rolls is often very high. I've seen 100 foot rolls cost almost as much as 100 *yard* rolls. You can get it online including from Amazon - just make sure it's not made from vinyl, just for vinyl transfer. Especially good if it says it's laser safe.

@muskokamike127 Жыл бұрын

@@jimhatch5873 which do you use from amazon? I ordered their (fake) 3m 200 and 201 and it sucks donkey balls. It bleeds worse than a Charles Manson victim. Not to mention it tears like tissue paper when you try and get it off the roll. I say the stuff from amazon is (fake) because it's not real 3m masking tape. It's knock off even though it has 3m printed on the inside of the tube.

@EastCoastEngraving 2 жыл бұрын

I'm looking forward to seeing added stone products (marble & granite) to JDS's line. Then a video like this one, but specifically for marble and granite.

@photoguy42 7 ай бұрын

Enduramask is a product similar to this. It's available in rolls from 2" wide up to 4' wide for vinyl cutters. It's low/medium tack and works great. Tape, engrave/cut, spray paint, peel and you're done.

@user-dl8bg4xb9k 8 ай бұрын

Great tuorial! Thanks

@choppman 2 жыл бұрын

beautiful work

@spiritsculptor Жыл бұрын

Wonderful wonderful instructional for example thank you

@carriea8917 2 жыл бұрын

Thank you!!!

@LeoGwizdala 2 жыл бұрын

brilliant !!!

@MrAriano65 2 жыл бұрын

Interesante la forma de impresión, esa técnica combinada me gustó mucho, se agradece la información, saludos cordiales 🖐️ desde Chile 🇨🇱

@seagnatprepper9613 2 жыл бұрын

Thanks .. that helped me

@hectortorres8580 2 жыл бұрын

Thanks good job

@f1pitpass 7 ай бұрын

thank you!

@berndwagenknecht4057 2 жыл бұрын

Nice !!!!

@DaraVRose Жыл бұрын

Great videos

@cartonus 2 жыл бұрын

Thank you

@stevebosley6212 2 жыл бұрын

Enjoyed your video, I couldn’t get the sound to come on but it was very educational.

@DavidKenny64 2 жыл бұрын

Same here. Very weird, because I got sound the second time I played it.

@JDSINDUSTRIES 2 жыл бұрын

Sorry about that. Unfortunately during recording a mic setting got bumped. On certain devices the audio doesn't play correctly. We have found watching on a phone or similar device plays the audio correctly!

@utahprepper8925 2 жыл бұрын

@@JDSINDUSTRIES sounded good on my computer

@robsnider5154 2 жыл бұрын

you can also use the same masking tape to pull the 'weeds' Just take a strip and press it down over the area you are weeding and the 'weeds' will peel right off...

@azizqassim9257 2 жыл бұрын

Nice tip.. thanks

@magicman9486 2 жыл бұрын

nice tip thanks

@huma_siraj Жыл бұрын

I did my project that way. Its faster too as engraving takes a bit longer.

@davidcochran934 2 жыл бұрын

Greta video. I didn't know there was laser paper like that. I wondered how people got color on the work.

@ruftime 2 жыл бұрын

Yes, Same transfer masking tape used for vinyl lettering/stickers….i buy mine from USCutters. I use it all over the shop😎

@magicman9486 2 жыл бұрын

it is not laser paper. it is transfer tape used in vinyl transfer. can be purchased at any sign or silkscreen supply shop.

@obtv6827 2 жыл бұрын

It's not laser paper it is low tack masking for transfering cut vinyl lettering for signs.

@richardg3232 Ай бұрын

Wow, this video was great. It was quick, easy to understand, no annoying needless music and the results speak for themselves. This plaque looks great. Where do you get that 'black' wood? I subscribed.

@JDSINDUSTRIES Ай бұрын

You can view them on the JDS website here: bit.ly/3q97Eu9 Thank you!

@danoldsbb4558 2 жыл бұрын

Briilliant

@AndrewHelgeCox 5 ай бұрын

For small details like text, leave the void and then smear a two part filler / modelling putty into the void after printing. This can work on surfaces at any orientation, not just flat top and bottom surfaces.

@hawaiibookmark 7 ай бұрын

Great video. In case you want to use the technical term, picking is called weeding.

@jgay672 Жыл бұрын

so does it have to be spray paint or can i use like wood paint

@magicman9486 2 жыл бұрын

wow!!! thanks so much. just bought a laser (actually 4 months ago, but only arriving now) and looking for any ideas to help pay off this very expensive purchase.

@michealcroes3377 2 жыл бұрын

Laser stufff

@billd.4701 Жыл бұрын

Can you please tell me the name of the masking tape and where to buy? Thanks for the great video.

@Brangustx 2 жыл бұрын

BRILLIANT! I would think you'd want the paint to soak into the wood, regardless, is that clear coat a matt finish lacquer?

@JDSINDUSTRIES 2 жыл бұрын

The product we used in this video was our LazerDark Clear Coat. Part number LDK200 on the JDS Industries website. It is a semi-transparent spray for enhancing the laser engraved area on most types of wood. Hope this helps!

@tomskubic5924 10 ай бұрын

What the main font you used on this plaque?

@shanefairchild5114 2 жыл бұрын

Great video! Learned a lot on this one. A few questions about cutting boards though. You use this same technique? Wouldn't the paint chip and peel over time, or is more for charcuterie boards?

@JDSINDUSTRIES 2 жыл бұрын

We have paint-filled cutting boards before. They are mostly just used for decoration purposes then but there are different sealants that some put on like some food safe oils and it seems to be fine. Wouldn’t recommend filling a whole board with engraving and use it but if it’s just a corner of it I’d say it’s fine. Hope this helps!

@shanefairchild5114 2 жыл бұрын

@@JDSINDUSTRIES this cleared things right up for me. Thank you!

@kariforrest9960 Жыл бұрын

@@JDSINDUSTRIES What type of paint did you use for the cutting boards and what tools? Also if for outdoor signs, what sealant would you recommend for acrylic paints?

@JDSINDUSTRIES Жыл бұрын

@@kariforrest9960 The paint we used is Rustoleum but most spray paints can be used! As for a sealant, it would depend on the substrate. If you are still thinking wood, something like a Krylon UV-Resistant Clear Coat should work.

@nikeeNZ 5 ай бұрын

Qow, thank you! Can i ask whs plack you used, it was so super shiney!

@JDSINDUSTRIES 5 ай бұрын

The material is the Black Piano Finish Plaque from JDS! You can view them on the JDS website here: bit.ly/3q97Eu9

@billd.4701 Жыл бұрын

Great video and thanks for posting. Does the masking tape come in a larger size? I need more than 12 inches wide.

@JDSINDUSTRIES Жыл бұрын

You can view the masking tape we used in this video here: bit.ly/3SaXzKp If you are looking for larger sizes, we do offer some here: bit.ly/3kJdraQ

@edmelzark1069 8 ай бұрын

How often do you need to clean the laser from the tape ??

@coulterjb22 Жыл бұрын

What would you suggest for color-filling lasered glass? Rub & Buff type or something else (I want to avoid overspray so rubbing might be best???)

@JDSINDUSTRIES Жыл бұрын

Rub & Buff should work!

@benjaminl3084 2 жыл бұрын

Nice video! Thanks for sharing. Do you have a link to that laser mask?

@JDSINDUSTRIES 2 жыл бұрын

You can view all of our laser mask offerings here! bit.ly/3abI94m

@bettyrobinson8222 4 ай бұрын

Awesome job. How did you do the black coat? Just spray paint, let it dry then do clear? It was so shiny that made it beautiful.

@JDSINDUSTRIES 4 ай бұрын

The gloss is from the the Black Piano Finish Plaque. You can view them on the JDS website here: bit.ly/3q97Eu9

@WORLDOFBLINGBLING Жыл бұрын

What kinda material is that you engraved on? Looks smooth and shiny! So magnificent work.

@JDSINDUSTRIES Жыл бұрын

The material is the Black Piano Finish Plaque from JDS! You can view them on the JDS website here: bit.ly/3q97Eu9

@royalmaster203 11 ай бұрын

THANKS, I was wondering how to fill color, I really appreciate your time, what are the brands you use?

@JDSINDUSTRIES 11 ай бұрын

Rust-Oleum is usually what we use!

@dasfreakster 2 жыл бұрын

Awesome. Where ya get those3 black plaques?

@JDSINDUSTRIES 2 жыл бұрын

Hello! You can view all of our plaque and accessory offerings here: bit.ly/3Hqz8Dl

@pdwoodwerkz9625 6 ай бұрын

Great video. What masking product did you use on the item in the video?

@JDSINDUSTRIES 6 ай бұрын

You can view the masking tape we used in this video here: bit.ly/3SaXzKp

@MSRWorkshop 3 ай бұрын

Oh!! Please send me the link of where to get that piano black plate from !

@JDSINDUSTRIES 3 ай бұрын

You can view them on the JDS website here: bit.ly/3q97Eu9

@JamesKing-fg3wn 2 жыл бұрын

Is it me or is the sound messed up, cant hear anything, volume to low? I still got the concept but audio explanation would be great. Good video!

@JDSINDUSTRIES 2 жыл бұрын

@kathleenswanson5750 2 жыл бұрын

I'm watching on a phone and the audio is not working properly

@LuisArturoFabreOrtiz 2 жыл бұрын

@@JDSINDUSTRIES actually I'm watching the video in a smartphone, and have issues with the audio

@andy1way 2 жыл бұрын

No it doesnt

@wildniscamper7276 2 жыл бұрын

@@JDSINDUSTRIES nope..phone not working.. just hearing: gschirarisxhissssssshhhhhtttsss😂

@demitajones7727 6 ай бұрын

i just purchased a wecreat, which a diode laser cutter, can this method be used with a diode laser cutter using 3mm basswood?

@JDSINDUSTRIES 5 ай бұрын

It looks like you should be able to use this same process!

@gurudataa1865 Жыл бұрын

Good day learnt a lot there ..shirt video but quite informational..wanted to find out about the black..what type of paint and how did you get the gloss?

@JDSINDUSTRIES Жыл бұрын

The paint we used is Rustoleum but most spray paints can be used! The gloss is from the the Black Piano Finish Plaque. You can view them on the JDS website here: bit.ly/3q97Eu9 Hope this helps!

@gurudataa1865 Жыл бұрын

@@JDSINDUSTRIES thank you very much

@maxpainop498 2 жыл бұрын

Would the masking tape be able to get transferred using transfer paper? In my case i want to paint plastic which is not laser safe

@JDSINDUSTRIES 2 жыл бұрын

This tape melts with plastic, so we wouldn't recommend using it to paint fill plastic. We wouldn't recommend paint filling plastic. If you need further information we'd be happy to help! Give us a call at 800.843.8853.

@sweetprimrose424 8 ай бұрын

Sorry if this is a silly question I’m still new to laser engraving, but would the tape not set fire? I think this is great idea but I’m afraid to use incase it would set the tape on fire

@JDSINDUSTRIES 8 ай бұрын

The tape will not catch fire!

@marcelomiguelbazan 8 ай бұрын

Hello there: This may be a silly question, but: Can you, instead of using a tool to remove the inner parts of the letters, just put another piece of masking tape to cover the letters, and make the first masking tape stick to the new one, and rip both at the same time? I know that's a waste of material (masking tape), but it should be quicker, easier, and without the risk of scratching the product. Thank you and greetings from Argentina. Marcelo Miguel Bazan.

@JDSINDUSTRIES 8 ай бұрын

You may still need to manually remove smaller pieces but using tape should work !

@mikeledee8786 2 жыл бұрын

I'm trying to find a way to maintain the color of the wood after burning, ie. American flags, the union, star field, after I paint the wood blue I want to burn out the stars I want to keep them white? Any tips?

@JDSINDUSTRIES 2 жыл бұрын

This would require a multiple taping and laser process, covering different areas at different times while painting it. This would be a good topic for another video. Thank you! In the mean time, our fabrication department would be able to help with a more detailed explanation. You can reach them at 855.537.2228!

@howdydoody30204b 2 жыл бұрын

Important details - What kind of masking tape, and what kind of paint? Thanks.

@JDSINDUSTRIES 2 жыл бұрын

Mid to high tack masking tape. Here is an example: bit.ly/3uqZu3c The paint we used is Rustoleum but most spray paints can be used!

@paullacombe144 Жыл бұрын

Nice! What is that nice glossy black?

@JDSINDUSTRIES Жыл бұрын

The gloss is from the the Black Piano Finish Plaque! You can view them on the JDS website here: bit.ly/3q97Eu9

@Hey_MikeZeroEcho22P 2 жыл бұрын

Hello, 'JDS Industries', my questions are .....1) I have a small tree of engraved parts, a model, with some fine etched detail. A Good majority of these parts needed to be "painted", so do I need that tape or do I just 'clear coat it', let dry, then spray the color I want? 2) What type/brand of paint do you recommend.......in your video, It looks like 'Krylon'? Thanks for your time.

@JDSINDUSTRIES 2 жыл бұрын

Masking off any area with tape that you don't want painted is important if you plan on painting. It is best to mask before engraving. We use Rust-o-leum here most of the time. Krylon we use for glass. Hope this helps!

@Hey_MikeZeroEcho22P 2 жыл бұрын

@@JDSINDUSTRIES Roger That, 'JDS'!! Thanks for the reply back and info. I did use a 'Rust-o-leum' Product with Great Success!! As far as masking I was able to remove the parts ...... That didn't need painted, so no problems there. But thanks for the assistance. :)

@cmbottorff 2 жыл бұрын

Could I use removable vinyl instead of the masking tape? I Have a lot of the vinyl from my cricut.

@JDSINDUSTRIES 2 жыл бұрын

Most vinyl is not safe for lasers. If it is laser safe, when you're rasterizing it (not vector cutting it) it’s most likely to melt onto your wood surface and leave extra sticky residue. You're mileage may vary as we don't have a ton of experience using vinyl as a masking tape. Hope this helps!

@cmbottorff 2 жыл бұрын

@@JDSINDUSTRIES It does. I did not even think about it melting! Thanks for getting back to me! :)

@stacyevans1360 10 ай бұрын

I used to weed like this then I learned that if you put duct tape over the engraved letters it weeds for you. No picking necessary and the application tape comes off intact too.

@user-fv8ku4sc2j Жыл бұрын

What brand of application tape do you use

@JDSINDUSTRIES 11 ай бұрын

You can view the tape we used in this video here! bit.ly/3zbiUM0 bit.ly/3uqZu3c

@skurniyantomappadang Жыл бұрын

❤

@missy7051 Жыл бұрын

What brand of paint is the best to use when painting acrylic?

@JDSINDUSTRIES Жыл бұрын

We use Rustoleum if the product is being masked and lasered. Rub n Buff if the product is already lasered!

@sadlermercantile 10 ай бұрын

Awesome video! You might try Gorilla Tape or Duct Tape to remove the masking as well, assuming it doesn't mess up the paint. I haven't tried it on painted objects yet, but it does wonders weeding unpainted wood and acrylic!

@joshswenk1967 2 жыл бұрын

I use lightburn, so the lingo may not entirely transfer, but do you uuse fill or line? Fill is the laser burning everything within the letter and line is essentially tracing the letter. Thank you!

@JDSINDUSTRIES 2 жыл бұрын

Fill!

@suburbansurvival5711 Жыл бұрын

This is what I was wondering. I have used fill before and it left residue. I have a diode laser tho….I’ll have to test out different settings. Thanks for the video!

@JDSINDUSTRIES Жыл бұрын

@@suburbansurvival5711 Adjusting your speed to faster should help solve the residue issue!

@user-bx9hy4ht7j 2 жыл бұрын

Can this tape be used with a fiber laser or is is co2 only?

@JDSINDUSTRIES 2 жыл бұрын

Yes. It can be used with a fiber laser!

@donnasims9972 2 ай бұрын

Where did you get the black wood cause you’re talking about engraving on wood and it looks like black tile pieces or something.

@JDSINDUSTRIES 2 ай бұрын

The gloss is from the the Black Piano Finish Plaque. You can view them on the JDS website here: bit.ly/3q97Eu9

@denniswilkins323 Жыл бұрын

how do you get that shiny black finish.

@JDSINDUSTRIES Жыл бұрын

The gloss is from the the Black Piano Finish Plaque! You can view them on the JDS website here: bit.ly/3q97Eu9

@adrianwilliams-ug2lf 6 ай бұрын

whats make is the clear coat spray?

@JDSINDUSTRIES 6 ай бұрын

Laser Dark!

@mikeledee8786 2 жыл бұрын

Do you use paper tape or plastic/vinyl tape on to of the product? Thanks.

@JDSINDUSTRIES 2 жыл бұрын

Paper Tape! Plastic/vinyl tape does not mix well with the heat of the laser.

@mikeledee8786 2 жыл бұрын

@@JDSINDUSTRIES thanks

@neco72 Жыл бұрын

Hello. Have you ever tried lasering chocolate to make words ?

@JDSINDUSTRIES Жыл бұрын

Unfortunately, the heat of a laser would probably be too much for chocolate!

@huishienGan Жыл бұрын

Can we paint fill on acrylic just like how we do on wood?

@JDSINDUSTRIES Жыл бұрын

The masking tape we used in this video wouldn't work with acrylic as it would most likely melt to it. Unfortunately JDS doesn't have a mask offering that works with acrylic at this time. Hope this helps!

@Dancopymus Ай бұрын

Without subtitle? You are only speaking to Americans! Still, I gave it a like.

@toso42 2 ай бұрын

What is the paper on the top ?

@JDSINDUSTRIES 2 ай бұрын

You may be talking about the masking tape? If so, you can view that here: bit.ly/3SaXzKp

@Puyax01 9 ай бұрын

Is the masking tape a regular or laser specific? Can't find it for laser

@JDSINDUSTRIES 9 ай бұрын

You can view the masking tape we used in this video here: bit.ly/3SaXzKp

@Puyax01 9 ай бұрын

@@JDSINDUSTRIES thanks, so is normal masking tape , right?

@JDSINDUSTRIES 9 ай бұрын

It is! A mid tack tape.

@Puyax01 9 ай бұрын

@@JDSINDUSTRIES thanks again. 💪

@kennykauk4834 2 жыл бұрын

Will it work on small cursive writing ? I had a lady write a recipe and we engraved it on walnut (her choice) we are pretty new to this but you can’t see the writing very well , it’s on a cutting board and takes up almost the space

@JDSINDUSTRIES 2 жыл бұрын

Small detail does work, but can be trickier. It needs to dry longer. And really ensure the masking is down well before and after engraving. Using a blank sheet of paper and squeegee to go over it to make sure the tape is down really well before spraying it. Then a clear coat before the color of choice, letting it dry really well and when going back to weed it be very careful. Hope this helps!

@djoleat 2 жыл бұрын

what is first spay ?

@JDSINDUSTRIES 2 жыл бұрын

The first spray we used in this video was our LazerDark Clear Coat. Part number LDK200. Hope this helps!

@EPT915G 10 ай бұрын

Where can i purchase this masking tape?? All I see is transfer tape. TIA

@JDSINDUSTRIES 9 ай бұрын

You can view the tape we used in this video here! bit.ly/3zbiUM0 bit.ly/3uqZu3c

@kennethrigg7320 2 жыл бұрын

what did you coat your wood with first

@JDSINDUSTRIES 2 жыл бұрын

In this video, we applied a clear coat first. The product we used in this video was our LazerDark Clear Coat. Part number LDK200. Hope this helps!

@AsafMatan Жыл бұрын

Hi, do you have amazon link to the cover tape?

@JDSINDUSTRIES Жыл бұрын

These masking tapes are available from jdsindustries.com. You can view them directly here: bit.ly/3SaXzKp

@AsafMatan Жыл бұрын

@@JDSINDUSTRIES Thanks a lot!

@AsafMatan Жыл бұрын

BTW are you shipping to Israel?

@AsafMatan Жыл бұрын

Hi- Re-asking

@moeibrahim6020 Жыл бұрын

U should reupload with audio

@JDSINDUSTRIES Жыл бұрын

We have! That video is available here: kzfaq.info/get/bejne/e5eGpclk27Wum4k.html

@legzn2423 7 ай бұрын

So what setting is “just right?” Lol. Is it neutral?

@thedysfunctionalwoodworker9611 Ай бұрын

I am not the OP, but I am a woodworker that uses a laser. The answer will depend on your laser type and power AND the making material that you use. EG: The settings for someone using a 5 watt diode laser and 3M yellow masking tape would be different than someone using a 100 watt co2 and Frog Tape. What I personally did was take a piece of scrap and cover it with mask material then ran speed & power tests to find the "just right" setting. Those settings will likely change if you change masking material and possibly the material you're engraving on. I hope this helps.

@burningempire666 5 күн бұрын

Picking out the little bits of tape is risky and tedious. Get some strong adhesive tape like Gorilla Tape and all the little bits will lift right off of the box

@dlealchicago 2 жыл бұрын

Love that black glossy board! What is that called?

@JDSINDUSTRIES 2 жыл бұрын

This plaque is part of our PNB series. The Black Piano Finish Plaque. You can view them here: bit.ly/3q97Eu9 Let us know if you have any other questions!