Jeep Superduty Axle Swap Made EASY -

No video

Jeep Superduty Axle Swap Made EASY -

Рет қаралды 3,459

Күн бұрын

Watch and learn to install the ‪@ArtecIndustries‬ Apex Swap Truss…the ultimate axle truss on a Jeep with minimal welding! In this guide, I will demonstrate how to upgrade to a Superduty Dana 60 axle with the strongest and easiest-to-install truss on the market. Artec’s high-quality truss fits seamlessly, ensuring maximum strength and durability for your off-road adventures. Join me as I show just how simple a ton swap can be making it accessible to both seasoned enthusiasts and DIYers alike. Don’t miss out on transforming your Jeep with this game-changing axle truss upgrade!
Follow me:
• Instagram: @WarPaintOffroad
warpaintoffroa...
LINKS:
JEEP ONE TON AXLE BEGINNER’S GUIDE
• One Ton Axle Swap Begi...
AXLE SWAP PREP
• Prep a Superduty Dana ...
JEEP FRONT END ALIGNMENT (Part 1)
• CAN I ALIGN MY JEEP AT...
PART 2
• CAN I ALIGN MY JEEP AT...
WELDING TIPS
• Welding Tips and Trick...
Music Credit:
Driving Zone - Arthur Basov
Disclaimer: This video is intended for educational and entertainment purposes only. Always prioritize safety and consult a professional if you aren’t sure about any steps. Injury can result in poor construction and modification of your vehicle. War Paint Customs LLC is not responsible.

Пікірлер: 18

@Kruncher55 3 ай бұрын

I couldn't imagine ever doing something like this, but can watch your videos all day long! Find yourself out in the Vegas area, drop me a line. We can show you around our trails.

@WarPaintOffroad 3 ай бұрын

I’d love to. One day I’d love to make it out there.

@jackcoy361 3 ай бұрын

Some of the best videos on KZfaq... Be patient... Your site is going to explode! Thanks for the great videos keep up the amazing content.

@WarPaintOffroad 3 ай бұрын

Thanks for the support and the feedback! It’s much appreciated.

@ericlecko 3 ай бұрын

Thanks for the video.

@WarPaintOffroad 3 ай бұрын

Thanks for the support! I’ll have more videos from this build and these axles in the next couple weeks.

@beetlebailey 2 ай бұрын

Here iit is found it.

@greershaw6169 4 ай бұрын

When I did my swap a couple of years ago I went with the Artec Apex kit. No regrets. The one thing I’d suggest is a hole in the 14 bolt truss to make it easier to install and ARB.

@WarPaintOffroad 3 ай бұрын

Yea. I have had to cut holes in them too. But so many people don’t run an air locker and use a grizzly. But honestly, I have also seen so many people put their air fitting in different places on the 14 bolt too. So maybe that’s why they don’t? I have to think that if they didn’t, it was for a reason. Everything is so well thought out…so there must be a reason they didn’t.

@StormbornJKU 4 ай бұрын

Artec does make killer stuff. I like their products a lot! Big fan of Barnes as well. I also have a hodge lodge of other brands brackets on my jeep lol

@WarPaintOffroad 3 ай бұрын

I am not a fan of Barnes. I have their stuff in my Jku and it was a HUGE mistake. There were so many parts and pieces that had to be very adjusted to fit. And a few things that just plain didn’t work. There are a lot of other options that are better made.

@mariob5764 3 ай бұрын

This type of modification makes me want to build a jeep.

@WarPaintOffroad 3 ай бұрын

Man I’ll tell you…this jeep is going to be really fun…when it’s done. The rear axle is going to be really wild. More so than the typical one ton axle swap. Those video should start rolling out in a week or so.

@jonathancharles6676 2 ай бұрын

I’ve got the same eastwood welder and I’m currently welding on the apex truss. My welds however aren’t anything close to what you’re putting down. I’ve got it set for 250 amps and 20 volts but it seems like I’m not getting the penetration into the tube that I was hoping for. What voltage did you use when you were welding the truss to the tubes?

@WarPaintOffroad 2 ай бұрын

So do you have it hooked up to a 220 outlet? Because that will change things. The digital read out in mine is set to 150-170 wire speed and 18-19…depending on what I’m welding. Then I just move slow with a 75/25 argon mix and the gas set to 12 psi. But I tend to weld slow. Which puts more heat into it. I spend a tiny bit more time on the thicker stuff and kid of whip the puddle onto the thinner stuff. I also tend to do a side to side “Z” pattern instead of loops like some others do.

@jonathancharles6676 2 ай бұрын

@@WarPaintOffroad ok cool. Yeah I’ve got it hooked up to a 220 generator. I felt like I was moving fast for the wire speed but wasn’t sure how to best increase the heat to the work piece without getting crazy undercut. Thank you for the help and thank you for the videos you inspired me to build my own set of junkyard tons!