John Deere Zero Turn Throttle Cable Replacement With Detailed Step By Step Instructions Z345 Mower

No video

John Deere Zero Turn Throttle Cable Replacement With Detailed Step By Step Instructions Z345 Mower

Рет қаралды 2,202

Күн бұрын

Thank you for watching!! If we helped you out and you want to show your support - LIKE, SUBSCRIBE or give us a shout out below. If you saw something you didn't like leave your comment below as well, these things help us get better!
To see our recommended tools and products visit our Amazon shop at www.amazon.com...
We show you how to repair a John Deere Z345E zero turn mower that has a throttle cable that needs replaced
This same process works for many other models that John Deere makes. We show the full repair process on this zero turn riding mower
This is the same/similar design as the John Deere Z330R, Z330M, Z335R, Z335M, Z345M, Z345R, Z355E, Z355R and others possibly
Throttle cable part number AUC10079 can be found at amzn.to/3KZk1DK
If you need to go through the electrical testing of PTO switch, solenoid or safety switches please visit • Riding Mower Won't Sta...
If you need to replace the wiring harness on a John Deere mower like this see the video at • John Deere Z335E Zero ...
See the carburetor cleaning and running diagnosis on an engine like this at • Ariens Riding Mower Wo...
Tools Used:
Dewalt impact driver amzn.to/3z16OaE
Dewalt 1/2" impact amzn.to/4bYvteC
Neiko 3/8" impact socket set amzn.to/3RHyAQc
T Handle Torx Bits amzn.to/3VClhlf
Drill bit holder & bits amzn.to/4c1mmK4
Video equipment:
GoPro Hero 10 amzn.to/3O4LFkQ
GoPro Hero 11 amzn.to/48rIcVz
Like and subscribe to see more helpful videos like this one! Save some money by doing it yourself!
#johndeere #wiringharness #easyrepair #smallenginerepair #individualizedrepair #smallbusiness #diymaintenance #valve
About Us:
My name is Martin. I have been repairing tools and small engines for almost 20 years. We operate a small engine repair shop in Illinois. We service / repair Briggs & Stratton, Kohler, Kawasaki, John Deere, Cub Cadet, Toro Tecumseh, Loncin, Honda, Craftsman, Husqvarna, MTD, Troy Bilt, Simplicity, John Deere, Exmark, LCT, Generac and many more brands. We work on riding mowers, walk behind mowers, snow blowers, zero turns, generators, pressure washers and much more. We normally repair about 3,000 pieces of equipment every year and look at many more that are beyond an affordable repair. Hopefully our videos will save you some money and give you the information you need to work on your own equipment or figure out the issue at hand.
Disclaimer: Links included in the description are affiliate links. As an Amazon associate we earn from qualifying purchases. There will be no additional charge to you for purchasing here. We appreciate your support, which allows us to continue to provide original content!
Please be careful when repairing any piece of equipment and follow all possible safety measures. This video is for entertainment purposes only.

Пікірлер: 33

@IndRepair 9 күн бұрын

If you need to go through the electrical testing of PTO switch, solenoid or safety switches please visit kzfaq.info/get/bejne/a55yo7N5v9HNg6c.htmlsi=17YnlZNv-09CR5Se If you need to replace the wiring harness on a John Deere mower like this see the video at kzfaq.info/get/bejne/p9ppq71n3trOaYU.html See the carburetor cleaning and running diagnosis on an engine like this at kzfaq.info/get/bejne/laplerxhv5u0Ymw.html

@Rein_Ciarfella 2 ай бұрын

Nice touch including the idle adjustment at the end, Martin! Bookmarked the cable adjustment for future reference. Sort of like governor adjustment.

@IndRepair 2 ай бұрын

Definitely, same basic process but a little easier than governor adjustment even. 😊

@kencurtis228 2 ай бұрын

TY for Sharing

@IndRepair 2 ай бұрын

Not to difficult but definitely one that is intimidating for most

@gearhead366 2 ай бұрын

I have a Cub Cadet Pro Z 100, and I thought that there were areas of poor design that were difficult to service. After seeing this JD, my Pro Z is a marvel of engineering design. I can't believe what you have to remove to get to the throttle cable. On mine, the control station removes with 4 keepers, which gives you access to the throttle cable. It's a 5 minute job in real time. On mine, the engine bay traps debris, but nothing close to what was trapped under the huge cowling on that JD. I'll stop complaining about mine now. Thanks for the video.

@IndRepair 2 ай бұрын

Haha, definitely a crazy design. I have seen worse but rarely do engineers think of the mechanic in their designs. Thanks for watching!

@fartsackjack7081 2 ай бұрын

snazzy weld repair on that muffkin .....R,charles

@IndRepair 2 ай бұрын

Haha

@warenmann1042 2 ай бұрын

@16:25 The arm on the right hand side went on backwards. That is something I would have done. Good video. Thank You...

@IndRepair 2 ай бұрын

Haha! Ding ding ding! Didn't see it till ready to finish up and was very surprised I was just thinking how in the world? Good work

@philliphall5198 2 ай бұрын

Even if you park it in side best to put a tarp over it anyway 😊

@IndRepair 2 ай бұрын

The mice don't want to sleep without their blankee. Lol tarp and a bag of moth balls works wonders

@Travis141123 2 ай бұрын

We used to replace just the wire back when things were a bit more serviceable.

@IndRepair 2 ай бұрын

For sure! I was taught this way many years ago but sadly do not remember much of that lesson. Thanks for sharing!

@philliphall5198 2 ай бұрын

It’s hard to get correct size wire now 😢

@donwilliams5841 2 ай бұрын

I've noticed your equipment has different colored ribbons on them. Purpose?.....still enjoying the videos....👍

@fartsackjack7081 2 ай бұрын

differnt stages thru the process

@IndRepair 2 ай бұрын

We use them to signify what needs worked on, has been estimated/waiting, finished or whether they still need double checked. Just makes it easier to find things when you have hundreds of mowers you can pretty easily rule out many. Thanks for watching and for your comment Don!

@goofe.washington953 2 ай бұрын

There was some additional grass/brush behind the throttle assembly which I would have blown out….mainly because I’m OCD. Great video, as always.

@IndRepair 2 ай бұрын

Definitely missed that, thought it was cleaned up better than it looks. Thanks for your comment and for watching!

@stevenedington6265 2 ай бұрын

Right side arm was put back on the wrong way around.

@IndRepair 2 ай бұрын

Yes sir, you are correct this is the mistake I mentioned. Who does that? Lol, guess I was just frustrated because the camera just overheated and didn't let me finish up. 🙃

@wolfmanshere 2 ай бұрын

Arm backwards when screws fell out

@IndRepair 2 ай бұрын

Haha this is exactly what I was talking about! Thanks for watching!

@rickbroerman9267 2 ай бұрын

Great video once again 👍

@IndRepair 2 ай бұрын

I appreciate that!

@KevinCampbell-o1t 10 күн бұрын

At the 19:30 mark in the video you can see a small "can" to the left of the connector for the main jet solenoid. It has a spring loaded lever at the 3 o'clock position. Beside it there's a linkage that goes vertically up to then through the carb to the fin that's moved by the fan. Can you tell me if the plastic tab on the bottom of that linkage should be above or below the lever that's on the can? The engine is surging at all speeds and the fin is fully deflected out from the fan. If I hold the fin closer to the fan it smooths out. I'm guessing this has something to do with the choke because if I hold the fan too close to the fan the engine sputters with black smoke as though the choke is on.

@IndRepair 9 күн бұрын

The plastic sits below the lever. This is likely telling you the carburetor is gummed up or has inferior quality fuel causing this issue. We show the carburetor cleaning on one of these if you have the single cylinder Intek at kzfaq.info/get/bejne/laplerxhv5u0Ymw.html

@joeh2253 2 ай бұрын

handle was on wrong

@IndRepair 2 ай бұрын

That is definitely the mistake I mentioned! Looked at it afterwards like what in the world!? Haha! Good eye!

@crisprtalk6963 2 ай бұрын

Not too tough a job. Darn, now I gotta go back and see what I missed!! ahhahahah

@IndRepair 2 ай бұрын

No, not too bad at all really! I have just seen so many homeowners intimidated so they won't even attempt it. This one was quoted $240 labor from the dealer