You're a good wrench Brad. I am 70 and know Harley's like the back of my old hand, and you my friend are a good shit, doing a great public service! Glad to support you and thanks!

Great video! Well done from start to finish, learned a fair bit, confident to attempt a rebuild. Thank you

Wanted to say thanks again- The snowblower is working great! Bought the Carb bowl tool you suggested! Your help was invaluable! Thank you for sharing your expertise!

Outstanding video. The detailed commentary and close-up video was especially helpful for me to reassemble my neighbor's snow blower that I messed up by removing the bowl to drain old gas when the float pin fell out. I then lost the needle valve & spring also. Using your video I purchased the kit from a local small engine repair shop and "carefully" replaced the missing parts and put it back together. Thank You for making a video with enough details to show and explain how things (should) work.

I worked in a small engine repair shop for a while. For carb bowls that had buildup like yours did, we used a Dremel instead of a wire brush to clean it. Works like a charm!

Amazing amount of clarity with a ton of information being presented! This video got me through a surging problem with the Tecumseh engine on my Ariens snow blower. Thank you!

I used to manufacture tools one of the items was a plastic magnetic ring that went around a screwdriver. I called it a Stayzon®️ that would be very helpful when inserting a screw into the carburetor. You can also get larger ones that will work with sockets or I’ve even used them when drilling steel to collect metal shavings. I enjoy your videos!

I have a 1984 Sears lawn mower that I refuse to let die. That Tecumseh is an amazing engine and just keeps working. Much larger oil capacity, gas capacity and power compared to the Sears Honda I bought to replace it (but only used for a couple of weeks because its under powered). The mower base is mainly made out of pop rivets and sheet metal at this point, but it still does the job. Had fuel delivery issue and took carb apart (first time in 40 years). I was cleaning it with compressed air and blew the needle seat somewhere in my shop so the job grew from a quick clean to a carb rebuild. Although needle/seat/gasket kits are cheap online ( you can get multiple kits for under $20 - no idea if they are any good), I just went to my local supplier and got one for $10 CAD. Thanks for the guidance. Much appreciated - especially the orientation of the seat. I just reassembled it this afternoon, flushed the tank out and that engine started right up and purrs better than it has in the 24 years since I inherited it from the previous house owner.

Thanks for adding float seat install instructions - that's what i needed to know. Nice vid.

Thank you, I followed your video and, successfully rebuilt my first carburetor. My 20+ year old craftsman snowblower will live to see another winter.

Excellent presentation!! You made me an expert on these carburetors. THANKS!!

I spray Kroil oil on the emulsion tube, let it sit for a few minutes and they usually pop right out.

Great job explaining these steps to put this Carberator together... I had the bowl off of mine and came across your video to watch to see how the bowl was orientated with the low spot... Perfect thank you!

Awesome carburator lesson. Thank you so much!

As to removing the plastic pin. I used an exacto to cut the portion inside then used an Allen wrench to froce it out. I did remove the choke lever to make it easy. Popped right out w the gaskets intact!! Thnx dude!!

Well done. Nice. Very helpful. Mine is a really old one with a brass float and no drain. Probably 1989. Detail for float valve seat was VERY helpful. Edit... first pull!!!!

Excellent video! Really appreciated the close attention to detail and fine camera work 👍🏼Thank you so much

GREAT video! Love the attention to detail explanation and close up camera work.

This is the best video I've seen yet. Really good job

Certainly the art of carburetor rebuilding is slowly dying and being replaced by cheap foreign knock-off replacement parts. Nice to see this video being thorough. While foreign components may work fine, those foreign parts are typically not built to the same tolerances as the OEM parts and usually do not last very long. I have been rebuilding carburetors for 55 years since I was 12 years old (just for fun) so I can share a few thoughts. First there is no single correct way to do a rebuild. Use whatever tools you may think you need keeping in mind that nothing should be unreasonably forced. Soaking a carb body in mineral spirits or kerosene will help loosen gunk build up in older seldom used carburetors. Compressed air is a great way to clear orifices in the main valve and carb body, but be careful not to blowout a seat that you are not replacing. Sometimes a rebuild will seem too simple and you might second guess if you did it correctly. Trust yourself and your work. Carburetors are meant to be repaired fairly easily. The engineering is built into the designs. All you are doing is a refresh. Wear eye protection especially when using chemicals, and wear gloves especially if you have allergies, skin conditions, etc. If you put a good hand lotion on before you work it will help your hands clean up afterwards and protect your skin a bit better. Enjoy the time and the dying art. Its rewarding.

Thank you for showing me the use of the tool to set float height. Been doing it by “eye ball”. For a few hundred of them. Nice to know the proper procedure.

Mine would not stay running without full choke. I disassembled the carb to find nothing wrong. Then I remembered your comment about the vent. Sure enough, it was plugged with muck. Superb video, thank you!

Great video and camera work! Just picked up an Ariens Rocket VII tiller and an old Horse tiller today. Both need carb work! Subbed and thumbs up! I love restoring/repairing the older stuff. Hands down better than the new garbage being made today.

Great video on explaining everything!

Got my first Ariens and a brand new one. Doing some maintenance on the old 24 inch 824 model. Your channel IS SIMPLY AMAZING. Love the way you explain things. And this particular vid has been very helpful to me. Thank you so much and God bless you

Great video, good detail and video shots.Thanks from N.S. Canada

Thanks for all of your great videos. I have learned so much about carburetor repair. Keep up the good work!

Thank you thank you thank you! I've never done anything like this and your video helped me feel like an expert when it was all said and done. Will definitely be subscribing to your channel!

Great video, thank you! I now did my 1st carb and am going to swap it tomorrow. Will follow up with report

Excellent details, easy to watch and understand with your narrative and subtitles.

Excellent video! Very detailed. Thank you so much!

Excellent Job. I have a 4 horse Tecumseh with a carb that needs to be rebuilt..Thank you for your time I learned a lot.

Great video. A nice professional work space. Well organized. Nice !!

Great video it’s Fourth of July I was out in the yard for hours taking everything off of my 24 inch Toro snowblower which has identical carburetor. Last we never had issues with it starting due to the primer button I have all the parts including a new carburetor by Luck,But I was very interested in rebuilding mine also so this is the identical carburetor that I have and I think I want up rebuilding mine and still keeping it adding the new one on the snowblower so this is a very good detailed video that you made I enjoyed watching it I’m learning about the carburetor that I have on my snowblower

I really appreciate your knowledge and sharing it with us. Thank you very much.

Great video and timely as I have a Troy-Bilt with this carb and it's in need of a repair, just like you did. Thanks for the video.

Thank you for this great tour! It pointed out a couple mistakes I made rebuilding one that was almost the exact same. Mine has a metal float and an idle needle. Was having a leak which seems to be fixed but I'm still having an issue where it seems to drink up the gas in the bowl and kill the engine faster than new fuel is delivered. Even though it flows fine with the bowl off and the float dangling. I might need to play with the float adjustment some more. We'll see if a ROP shop carb does any better.

Great video thanks for doing it very helpful when doing mine I have the same carburetor that had a small spring sitting in the bowl don't know where it belongs but it runs well

You rock, thank you!✌🏼

Good work! Thanks!

Outstanding! Thank you!

Super helpful! Appreciate the step by step. My first one! Thanks very very much.

Great job. Thank you so much.

Awesome video......thanks so much for sharing your knowledge

Westleys bleche white tire cleaner works amazing to get that brown varnish off, even when carb cleaner fails.

Thank You!

A very small crochet hook the smallest one they make works great on taking out the emotion tube

excellent! Thank you!

you saved my day with this video, thanx

Great video. Surprised teh kit doesn't have the mounting gasket.

Excelente video, gracias por compartirlo

Awesome video...a small screw work real well to screw into emulsion tube and pull it out

If you have a lathe, you can lightly clamp the bowl in it and run some 400 grit sandpaper to remove the grit around the top of the bowl, and then I burnish it with aluminum polish and a cloth.

Great video, well done!

Great video.

Thank you for the good help brotha😀

Another great video, thanks again

Your video was awesome.

Good job. Thanks

Followed your video. It worked . Thank you

Video is very well done!

This video very helpful. Keep make videos like repairs. Good luck bro...😊

Very good !!

Great info.

GREAT video!!! I just subscribed.

very knowledgeable, thanks for sharing.

Oustanding video. Thanks.

Try using a little bit of grease on the tip of your screw drivers to hold small screws, especially BRASS. Great show

Very good video. I have a 10hp snow king that's giving me crap. I ordered an "OEM" carb which looked and sounded like shit. I will be rebuilding the carb and see what happens.

Me gustó, muy bueno

Thanks.

When my mower is 5 cm lower on the left side while mowing it stops working. Might be ignition or carburator. Thank you for your video ill try if rebuilding the carburator will change my situation 😀

very nice Job...

Thx!

I am a very lucky person as my Tecumseh carburetor is so rare, it must be worth an absolute fortune. It is a '9' Series Carburetor (9004 L6R) and I am trying to get a service kit and '172' replacement fixed jet, but nobody in the UK seems to have heard of it. I wonder if a normal service kit and adjustable jet bowl nut would get it back into service? Very frustrating.

What cleaner do you use In your ultrasonic cleaner?

That Tecumseh tool for the emulsion tube gasket is just a crochet hook. lol Or you can use an 11/64 drill bit to check float position.

Great video ! Very good explanations and excellent camerawork, my carb is working good but I can wait to rebuild it soon thanks to you !!! One question, if I don’t have a tool to set the needle correctly, then can I use a drill bit or feeler gauges ? What would that gap be ? Thanks

Another great video! Don't know why I say that because all of your videos are so informative and like the way you explain everything. I have one question. I just purchased a. Ultra Sonic Cleaner. What did you put in it to clean the carb? I believe there are some liquids you can and cannot use?

I know it's that time of year for snowblower use. But you just never know when the carburetor goes bad. But hey good job on this one.

Is the Emulsion tubes hollow or are they solid inside ? If hollow, can you run a fine wire through it ?

Hi from Norway, the bottom nut/high speed jet: mine had a rubber gasket at the top but it felt off. Do i need a new one? Toro 8hp Tecumseh 😁

my techumseh carb had a tiny little clear plastic tube ,smaller than the size of a bb inside when I looked in the jet chamber.. not sure what its for.

Question what cleaner do u use in your sonic cleaner for carbs like this?

What cleaning solution do you use in your ultrasonic cleaner for the carbs?

I've been having a surging problem with a yardman snowblower. My bowl is sitting a little high due to a swollen pin seal. I think I heard you mention that it means it won't then get enough fuel ? gonna take a look tomorrow. Or the surge could be normal as you mentioned gonna let it run longer but - what happens if the float is too high? (upside down view) Nice video.

Pulling that tube. Can you use a wood screw to help pull it out

What is the size of those emulsion tube O rings?

What are the adjustable and non adjustable part numbers for the hm80 carburetors? Am thinking about buying a replacement oem carburetor. I don't want aftermarket stuff. Might also need a new choke.

I just bought the whole thing for £15. It seemed to easy

What is your favorite solution for cleaning carbs in the ultrasonic cleaner? Nice video.

Does a plastic float sit at a different level than an old metal float? Does the tool work for both to adjust the height.

good video! when I prime it, gas leaks from carb over the float bowl any ideas?

So I'm in the process of troubleshooting my old Ariens mower. Pretty sure its the carb and there's some issues of fuel not getting to the carb b/c it will run if we pour fuel down into the Air intake. If all else fails and I need a new carb where do I find one? The carb is a Tecumseh 632524. It is from a TVS120-63111F on my Ariens 911016 mower from the 80's. Your video has been exactly what I'm looking for though, I didn't realize how many other small holes there are that I need to poke out and spray carb clean on. sheesh

what do you use in your ultrasonic cleaner for cleaning? ex. simple green or degreaser?

Hi, Good video, do you have any idea how to rebuild a Nikki carburator 150037092? Kawasaki engine v twin 21hp

Do you have a similar video for an adjustable tecumseh carburator?

I know this is about carbs but i discovered myissue was not the carb it was a stuck exhaust valve. I fixed it by spinning it through the sparkplug hole using a small flathead screwdriver and spraying PB blaster.

Great video Brad, but I have a question. How can I set the float height without having the Tecumseh tool? Thanks again.

I have this carb on my tiller. Rebuilt it using B&S kit and it responded great. Engine starts and runs very well with the exception of running rich. Any advice on what may be causing this! Did not change the emulsion tube as I’m not sure it had/has one.