Mate thank you for this video! Love the work your doing keep it up! Im rebuilding a Zx7r that’s been sat for 16years it’s been hard work but learning as I go. 👍

Excellent video 👍🏻 tons of good simple info

I have a zx750r. I once removed the components and submerged the carburetor with Pinesol. I left it there overnight and the next day it was clean as a whistle

Great video. Enjoyed your chilled warts n all approach! Subscribed to you mate.

thanks brother, you helped me out tremendously

Hi very nice video and bike i have one the same here in europe thanks for showing because i'm cleaning mine to

Great vlog.... please make a video on the 06-07 gsxr750 coil stick conversion with the wiring.... I did a 2009-12 zx6r throttle and start/stop switch conversion with repining wiring to pnp with existing 1996-2003 P model wire harness... I have a 2003 P8 with K&N air filter, stage 3 jetting and a full micron system thinking of adding the +4 advancer....

Thank you for the plug Brother

Very niiiice Damon lol niiice

Did you ever figure out your hot start problem sounds like bad starter to me. Thats usually what happens when a starter begins to go bad

Great video, I want to fit a K&N filter, Do you know what size jets i should use?

hey, I just bought is exact bike on marketplace, a 2001 model, and the fuel line coming from the petcock is not connected to anything and is a clear tube. Can you tell me or do a video just describing the fuel line arrangement of the bike, it would help alot! Thanks

Hey man, great video! My 93 Zx7 has a bit of a dead zone between 4k-6k RPM. Do you know what this could be?

Hi from the UK. Thanks for the video. I have running issues (won't idle, runs on 3 cylinders maybe) since bike been sitting for couple years, with me starting it & letting it run up to temp once a month. It sounds like fuel jets are blocked to me, so can I just clean these from the float bowl rather than taking the other side apart? Also as I'm mainly using cleaner on the jets ok to use brake cleaner, as I don't have carb cleaner? Thanks

Thanks man. My bike had problem when up shifting. It bogs for the first 2 seconds in 3rd 4th and up. Do you have any ideas? I think it was the needle. Just bought it though

I had my first run yesterday on the zx7r. It runs all good after 4 month hibernation. Anyway, I have an unrelated problem. I've noticed that my blinker light on the dash doesn't work. Is there an easy way to change the bulb without taking of the whole front end fairing?

Dude I have a j model and it starts fine but it will not rev past 6k ! Have had the carbs apart 3 to 4 times any ideas?

Working with fuel, you really should remove the battery, incase a tool drops on the terminals and sparks.

Great video!!! . Do you have a video of you replacing the valves??

how did you fit the 06-07 swingarm on the zx7r?

Hi my 02 zx7r start and died I think is carburetor problem but never done carburetor

Motorcycles do not have to pass smog in California in order to register.

Will this work for zxr400?

I recently bought a 2000 ZX7R that was in need of some TLC, bike starts up pretty easy and seems to run ok BUT the bike was stinking my garage up BAD every day with fuel smell with no visual fuel leaks (tank needs to be painted anyway) so I drained the fuel and removed the tank, checked petcock which seems to work correctly and I didn't notice any leaks I was able to get my finger slightly wet with fuel by rubbing finger around petcock seal nothing major at all. Once fuel was drained and tank removed the fuel smell is pretty much gone .... I have since noticed that my oil may smell like fuel but im not 100% sure .... someone suggested that my floats are likely sticking causing fuel into the engine and creating the bad fuel smell but im not sure because the petcock seemed to work correctly and I keep the petcock OFF when not running the bike and the bike starts up pretty well never seemed flooded out, and also as I mentioned draining the fuel and removing the tank cleared up 99% of the fuel smell. What are your thoughts?? I don't know what I should do next, clean / check the carbs maybe (I ordered a carb rebuild kit in case its needed but I don't really want to tear into the carbs if I don't need to), I also bought oil but not sure if I should do a oil change until I know for sure what's going on and know for sure if fuel is getting into the oil. Any thoughts and advise would be appreciated! Thanks!