KENMORE 600 SERIES WASHER HOW TO CALIBRATE RECALIBRATE STEP-BY-STEP INSTRUCTIONS FACTORY CALIBRATION

Рет қаралды 10,040

5 ай бұрын

CORRECTION!!!!!!!!!!! AFTER YOU GO THROUGH THE 1-2-3 1-2-3. 1-2-3 STEPS YOU SHOULD TAP SPIN SPEED BUTTON NOT THE CYCLE SIGNAL BUTTON. SPIN SPEED WILL PUT YOU IN CALIBRATION MODE.
PLEASE DONATE TO HELP FUTURE PRODUCTION OF OTHER VIDEOS TO COME paypal.me/applianceflipper8590
Welcome to APPLIANCE FLIPPER 8590Your Ultimate Guide to Home Appliance Mastery!
THIS IS A 050 RUN FACTORY CALIBRATION
Explore the world of efficient home management with our expert tutorials and step-by-step guides. On this channel, we specialize in unlocking the full potential of your household appliances, and our latest series is all about the Kenmore 600 Series Washer.
In this dedicated playlist, we break down the calibration and recalibration process of the Kenmore 600 Series Washer with detailed step-by-step instructions. Whether you're a seasoned DIY enthusiast or a first-time homeowner, we've got you covered. Our goal is to empower you with the knowledge and skills to optimize the performance of your washer and elevate your laundry experience.
Join our community of home enthusiasts as we dive into the intricacies of appliance maintenance, troubleshooting, and upgrades. Subscribe now and never miss a beat - your laundry routine is about to reach a whole new level of efficiency!
Don't forget to hit the notification bell to stay updated on the latest tips and tricks for your Kenmore 600 Series Washer. Let's make every cycle count - welcome to APPLIANCE FLIPPER 8590, where home appliances meet expertise!

Пікірлер: 34

@8060ren 18 күн бұрын

Your the only one that knows this ? Very good info saving me having to get another washer … again .

@MariaLara-pr6yr 3 ай бұрын

You stated after the 123,123,123, process to hit Cycle Signal once an turn Dial to 050, but in the video you hit SPIN SPEED not Cycle Signal I am saying this because I hit the cycle signal first and nothing happened but then I went back and did it over again and I hit SPIN SPEED. Then I was able to turn the dial to 050 then the process continued.

@applianceflipper8590 3 ай бұрын

Thank you Maria you are correct I noted that mistake in the description.

@victoriagodwin1949 21 күн бұрын

My washer runs regular wash cycles for hours longer than its supposed to. Will this fix it?

@kennethsoriano537 21 күн бұрын

My load failure got when clothes were in it, will it calibrate with those clothes still in?? Fix this for me, I'll show some love.

@Z-Ack 21 күн бұрын

Can take it all huh..? Anybody ever tell you that your a real life version of cleveland? Kinda.. lol. Sorry.. keep doing you dude.. wish i could figure out how to get into the business of appliance repair and reselling.. cant get any client base. But thats my dream i guess., that or an independent contractor remodeling bathrooms and kitchens myself.. cant build any client base.. i only got 4 or 5 people who have asked for big jobs and never get any calls back from them cus nothing ever breaks.. and guess their friends and family dont ever need anything done or they just dont tell em.. all of em were happy because i charged half of what any other company would have and kept all the detail in it.. dunno.. guess im just not lucky enough to get what i want.. never have.. good to see others doing it though..

@butterflyyournails463 4 ай бұрын

Thank you for the information. Are the noises on the video part of the calibration process? Thank you

@applianceflipper8590 4 ай бұрын

No this particular washer needs a washplate

@loripetersondc4l79 8 күн бұрын

How can i do this if my washers power button keeps blinking with the f5?? Even when ive unplugged it 😣

@applianceflipper8590 8 күн бұрын

1 of 3 problems Power supply problems unplug the unit for a couple of minutes that should reset itself. 2. Lid lock: make sure the lid lock is connected properly to ensure it is working properly if it is connected properly and still doesn't work replace it. 3. Inspect the temperature sensor make sure it is not damaged if so replace it.

@lashonsostres2786 Ай бұрын

Did again now I’m getting F2 and E1

@timyoung5230 Ай бұрын

Hi I went through the video and the 888 showed up 1x after multiple tries. I then lost it because it went over to an e2 but not 050. I tried again with multiple tries to redo things with no luck.

@lashonsostres2786 Ай бұрын

Error codes F8 and E6 flashing! I need help?!?

@mrdavis2928 2 ай бұрын

What do you do after it’s done calibrating and u see the 3 8s???

@sagitario12ish 2 ай бұрын

Just power off thats it.

@TrapOchestra 3 ай бұрын

What does it mean when this washer stops mid cycle

@applianceflipper8590 3 ай бұрын

if you can't calibrate then it could possibly be board problems.

@nelkboys1 Ай бұрын

My washer now throws 2 codes F5 and E3 and won’t do anything else?

@applianceflipper8590 Ай бұрын

Take a note of the correction I made in the description.

@arthurtorricer4544 3 ай бұрын

I understand to unplug it 2 mins.. but then what, plug it back in ,then you hit the Power button ..it doesn't look like your blue light is on in your video.. I hit the 3 buttons and it doesn't do anything. if it does it just scrolls through the different settings.

@MariaLara-pr6yr 3 ай бұрын

The reason it didn’t work was that you need to unplug 2min do the 123,123,123 step (DONOT PRESS POWER BUTTON first or anytime ) then you’ll see 888 then press SPIN SPEED (NOT CYCLE SIGNAL) like he states and goes on to press spin speed the dial 050 and it will proceed

@eac1907 3 ай бұрын

What’s the purpose of the calibration?

@applianceflipper8590 3 ай бұрын

Sets it back to factory settings and re adjust washer when it gets out of whack.

@lashonsostres2786 Ай бұрын

When I held cycle signal the 888 returned and a ding sounded

@applianceflipper8590 Ай бұрын

Did you see the correction I noted in the description?

@timyoung5230 Ай бұрын

Im getting an er and f6 code and cannot get to 050.

@applianceflipper8590 Ай бұрын

Take a note of the correction I made in the description.

@timyoung5230 Ай бұрын

@@applianceflipper8590 Hi I do not know what's going on with my machine. I went through the three steps and I tried it with the correction, and I get the 888s but I cannot get it to calibration mode. By fiddling around with the buttons I was actually able to run the machine through a couple of cycles but then it just goes back to showing me the er and f6 code. It does kind of appear as though your video might have got me onto somewhat of a right track it think, but it is still not working right now.

@applianceflipper8590 Ай бұрын

@@timyoung5230 Good chance your board is bad.

@user-dr4zz6kj3t 2 ай бұрын

Mine won’t go into this mode it is completely dead no power no modes

@applianceflipper8590 Ай бұрын

Take a note of the correction I made in the description.

@charlesway8825 3 ай бұрын

How do you clean the filter on this machine

@applianceflipper8590 3 ай бұрын

They're called inlet valves just turn off water valves hot and cold going to the washer unscrew the hoses going to the washer clean the valves the the hoses were screwed into. First use your hands to clean any debri then get a vacuum and suck the area off the screens.