How to replace a wheel bearing on Chevrolet Malibu
Рет қаралды 17,176
Күн бұрынHub assembly/ wheel bearing Replacement... 2015 Chevy Malibu
@chrishastedt9597 10 ай бұрын
You are a good teacher of trade lost years ago bless you Sir.
@KITS_Auto_and_Truck_Repair 10 ай бұрын
@chrishastedt9597 Thank you!
@nicke.3782 17 күн бұрын
Very informative. Nicely done!
@KITS_Auto_and_Truck_Repair 16 күн бұрын
@nicke.3782 Thank you!
@rzigmont Жыл бұрын
Great video! The bearing doesn't come off the hub assembly quite as easy as shown. Usually takes a great amount of pounding and prying, but we get how to complete the project. Thank you
@KITS_Auto_and_Truck_Repair Жыл бұрын
Robert Zigmont My Pleasure!!
@chrishastedt9597 10 ай бұрын
Depends on the climate you live in.
@petermartinez5573 3 жыл бұрын
Great video. You explained everything systematically and thoroughly. Good job my man. The only other thing you might have discussed is removing the protective coating from the new rotor. Much respect.
@KITS_Auto_and_Truck_Repair 3 жыл бұрын
Peter Martinez thank you!!!
@waynedickens4031 Жыл бұрын
Great video . I like your little asking what's next . Gets people involved. Nice . Enjoyed the video
@KITS_Auto_and_Truck_Repair Жыл бұрын
wayne dickens Thank you!!
@andrewmacauley3665 2 жыл бұрын
Awesome video! Thank you so much for the indepth explanation and good pace Through out the video. It really helped me do this to my car! Thank you!
@KITS_Auto_and_Truck_Repair 2 жыл бұрын
Andrew Macauley My Pleasure, I'm glad to hear that the video was helpful!!!
@jermelljackson1962 3 жыл бұрын
This was a great video. You explained things very clear. My only question is that why have you not removed the tire rod bolt? I Saw a similar video where they removed the tires rod bolt.
@KITS_Auto_and_Truck_Repair 3 жыл бұрын
Jermell Jackson thank you, I didn't remove the tie rod because I had enough room to remove the bearing... and the steering wheel was unlocked, so I could turn the steering knuckle without any problems...
@eclipse1999able 3 жыл бұрын
Awesome bout to do this on a friend's car. Thanks
@KITS_Auto_and_Truck_Repair 3 жыл бұрын
kyle o My Pleasure!!!
@rgvcateye9058 8 ай бұрын
Awesome video! What are the torque specs for the 3 bolts of the hub and the center nut?
@KITS_Auto_and_Truck_Repair 8 ай бұрын
@rgvcateye9058 Thanks! the torque spec for the bearing bolts is 74 lb ft and the drive axle bolt torque spec is 111 ld ft for the first time then loosen the nut 45 degrees then tighten it to 184 lb ft
@wellingtonmiller1622 3 жыл бұрын
Great job .
@KITS_Auto_and_Truck_Repair 3 жыл бұрын
wellington Miller Thank you
@elijahyousif5952 9 ай бұрын
Hello, can you please tell me where did you get the front wheel bearing hub assembly from ?
@KITS_Auto_and_Truck_Repair 9 ай бұрын
@elijahyousif5952 I got it from my local parts store!
@steveburns9684 Жыл бұрын
Great video..just one thing..What about pumping the brakes Back up when your done?
@KITS_Auto_and_Truck_Repair Жыл бұрын
steve burns Thanks! and yeah the brakes have to be pumped up at the end, thanks for pointing that out!!
@waltherherrera67 Жыл бұрын
Excelente 🎉🎉🎉👍👍👏👏
@KITS_Auto_and_Truck_Repair Жыл бұрын
Walther Herrera Thank you!
@jl-heatfan4life717 2 жыл бұрын
Ur explanation is on point 👍 but dont u disconnect the ABS Line Harness? Had a malibu with Hub Assembly that had ABS Line connector attach to it n it pinches the wire so i guess newer models is not attached ABS Line with Hub Assembly huh? Thank u bro
@KITS_Auto_and_Truck_Repair 2 жыл бұрын
J6IX LARRY21 My Pleasure!! Thanks
@mrburgess6777 2 жыл бұрын
Will this procedure fix the traction control/abs light indicator showing on my dash??? I can save lots of money doing this myself... Thanks for the video 👍
@KITS_Auto_and_Truck_Repair 2 жыл бұрын
Mr burgess if your problem is the abs sensor or the wheel bearing this procedure will help you fix it!!
@Juclo90 2 жыл бұрын
It’s necessary to putting back the rotors splash plate? Because the new rotors I bought is bigger than the factory I find in the car. It doesn’t fit in the splash plate. If I put it back without splash plate it’s fit but, but with splash plate it doesn’t. So I have to keep the splash or it doesn’t matter to keep it or not? Can you answer to me please. Thanks you
@KITS_Auto_and_Truck_Repair 2 жыл бұрын
Clauzel Etoyla you need the splash plate, you should get the right rotor!
@Juclo90 2 жыл бұрын
@@KITS_Auto_and_Truck_Repair thanks you
@KITS_Auto_and_Truck_Repair 2 жыл бұрын
@@Juclo90 My Pleasure!!
@elijahyousif5952 9 ай бұрын
What is the size of the axel nut ?
@KITS_Auto_and_Truck_Repair 9 ай бұрын
@elijahyousif5952 I believe it was a 32mm
@elijahyousif5952 9 ай бұрын
THANK YOU BROTHER SO MUCH AND YOUR VIDEO IS A TREMONDOUS HELP GOD BLESS YOU@@KITS_Auto_and_Truck_Repair
@KITS_Auto_and_Truck_Repair 9 ай бұрын
@@elijahyousif5952 My Pleasure!
@bowfeeznuts3912 2 жыл бұрын
What do I have to order an essembly or a hub
@KITS_Auto_and_Truck_Repair 2 жыл бұрын
BOWFEEZ NUTS yeah it's basically the same thing, you can say hub or hub assembly
@bowfeeznuts3912 2 жыл бұрын
@@KITS_Auto_and_Truck_Repair and for a 2016 limited front is it different from 2015
@KITS_Auto_and_Truck_Repair 2 жыл бұрын
@@bowfeeznuts3912 it's the same process
@PaPabearj1 Ай бұрын
Once I replace the Oxygen Sensor (upper), the engine began to die.
@KITS_Auto_and_Truck_Repair Ай бұрын
@PaPabearj1 did you install an aftermarket sensor in it?
1A Auto: Repair Tips & Secrets Only Mechanics Know
Рет қаралды 1,4 МЛН
All4HimRacingVideos
Рет қаралды 228 М.
s33therfan
Рет қаралды 10 М.
Авто95
Рет қаралды 3,6 МЛН