Brilliant video, much more helpful than I was even hoping for! Just a suggestion though, you may want to add some kind of tag to your video. I've just used the first 15 minutes to show myself exactly how to easily get to absolutely everything I need in order to fix the "E-001" error. You have made it simple to isolate all the correct wires, as well as removing the rear wheel to repair/solder any breaks that could be causing that exact fault. There aren't many videos that have helped with that fault (and on the exact scooter I was looking for). The ones I found were mostly non-english so I had no idea what was being said. If you were to add a tag for the E-001 code you might help even more people :)

Thanks a lot man ! If anybody around here is trying to fix the bearings of the urbanglide ecross pro, it’s the same only when you have to put back the motor inside the wiring are facing down and not up, otherwise it can’t go fully inside and you can’t close the lid

This looks so hard Mate

Nice vid. How much will you charge me to sort my scooter out. I've got a kugoo m4 and i popped the back innertube. I've been through about 5 tubes and they all pop. I ordered a solid back tyre for it but it doesn't fit even though it says its for m4. its doing my head in tbh lol taking the wheel off and putting it ack together for it to pop i think it may need a re wire because taking the wheel off all the time rips the wire casing. it still works fine but not really ridable with a flat tyre.

R u gonna show us the M4 doing 35mph with the speed mod?

I'm so thick I've just realised that you are in Wales mate I'm from Swansea no wonder I could follow everything you said awesome thanks again

IV had a tyre change now IV got error 1 and my scooter doesn't work the wheel spins when off the ground but makes a loud rubbing noise and when I try ride it it's cuts itself out

Can you put that motor on a g2max front wheel ?

Hi what size are the rear bearings and are they the same size as the front?

Yesterday my engine completely stopped working.and I step on the gas but nothing happens.😭 what do you think happened.❓❔❓

Do you have to open the battery screws to get to the wires

Hi i keep getting e006 and e005 error any ideas please

I have a grinding noise from the back wheel (Motor ?) when I accelerate but the noise goes when I release the accelerator even though the scooter is free wheeling, is there any demos to fix this problem, ?

Can u do same video but for kugoo G2 pro

Nice Intuitive Video's Bud, nice rear shocks, where & how much? I'll get back to you about the lighting kit's & foot plate designs, cheers

Hi my kuggoo M4 scooter charges okay but when I start it it cuts outs then won't go again and drains battery saying it's empty when it's just been charged fully ???? Any idea what it can be mate ?????

Hi there I really need to no something! What amp fuse can I put in a plug to charge my kugoo m4 kirwin?

Hello matte I got I problem to find one motor for my escooter, its a kerin m4 pro 500w .. can you recommend some place to buy one ? Regards Márcio Abreu

Wait there is a tubeless for m4 Pro

Hi mate I replaced my tyre tube and now I've got a error code 0001 a motor error but so it doesn't spin at all but when I switch of lights horn etc the motor starts to work but I just vibrates but when I put the scooter on ground it just vibrates

What would you do if u damaged the wire's,I have soldered back together but it still doesn't work???????

Hey I was wondering where you get your tyres from

You can grease the motor? (the magnets) Is that a good ideal? wont it cause any harm to the motor?

My KugooKirin G3 has becomebe locked down, How can I reset the speed?

You damaged your new bearing by taping it with hammer..

Mate don’t get offended but it sounds like your from Cardiff I my kugoo playing up got a motor error and I’m from Cardiff any chance of looking at it please

Where did you get tiers from please

The wire on my back wheel has been damaged and I don’t know what to do only had it a month

Need help with Erre coad 6

hello I am contacting you for help wiring controller for the kugoo m4

How can i get in contact with you, i have a few questions if you dont mind

Is it a good idea to lubricate the magnets in the motor?

awesome thanks for the videos mate I think it's great how you explain everything properly I'm not confident usually but after watching all your videos and having them to help me as I have a go helps 100 per cent keep it up it's definitely appreciated yours sincerely rjfb