Рет қаралды 21,390
The KuKirin G2Pro is an upgrade and optimisation of the KugooKirin G2Pro. Improved display, electric door lock, controller, light board module. These minor changes do not affect the mechanics of the scooter or the user experience at all. They are small changes that our factory makes every time the model goes into production based on customer feedback.
-------------
1. Insert the key and turn it to the right to turn on the scooter. Press and hold the [on/off] button to switch the scooter turn on and off.
2. After turning it on, press the [on/off] button once briefly to change gears, in three steps.
Press the [on/off] button 3 times in succession to enter the menu setting interface.
P1: Speed and mileage unit setting, 0-km or 1-mile. default km/h.
Press and hold the [on/off] button for 3 seconds, the value will flash; at this time, you can short press the [on/off] button to select 1-mile or 0-km; when 0-km is displayed, select km, Km/h will be displayed; when 1-mile is displayed, select mile, mile will be displayed; then press and hold the [on/off] button to exit and select other parameters for debugging; if there is no operation 8 seconds later, the parameter setting will be automatically exited (the same operation for other parameter settings). After entering the menu setting, if the current parameter does not need to be modified and set, switch to the next parameter setting interface after short pressing the [on/off] button once.
P2: Voltage level setting: 36V/48/52/60V/72V. Default 48V, no need to adjust.
(it is lower than the normal value of 48V, even if the display is full, the scooter is not actually fully charged. If it is higher than 48v, the battery level may display abnormally.)
P3: wheel diameter setting is based on the tire size of the scooter: unit=inch; can be set to 080-160 (080 means 8'', 100 means 10'', and so on), increasing by 5 each time.
the KuKirin G2 Max wheel is 10'', then the default wheel diameter setting of G2 Max is 10, and the Kirin G2Pro wheel is 9'', then the default setting of the Kirin G2Pro wheel diameter is 9, which does not need to be adjusted.
(If the wheel diameter is adjusted to a value other than the default wheel diameter, the speed displayed when the scooter ride will be inaccurate.)
P4: number of speed measuring poles: is set according to the number of magnets in the motor. Kirin G2Pro and G2 Max have 30 magnets, so the default value of p4 is 30. range: 1-100, default 30. no need to adjust.
P5: Cruise Control setting: 0 to cancel cruise control, 1 to set the cruise control. when cruise control is turned on, the cruise control icon flashes; default cancel cruise control.
Cruise control mode: The scooter is set to cruise control mode. Press the accelerator to ride. After the accelerator is released, the scooter will continue to drive at the current speed without pressing the accelerator.
(Kindly Tip: Please pay attention to safety when using this cruise control mode. The cruise control still will continue to ride when the accelerator is released. To stop, you need to press the brake.)
P6: Start mode setting, 0=zero start; 1=non-zero start, the start mode is displayed when the power is turned on (zero starts will not display the icon, non-zero start displays NON).
Kindly notice that after the power is turned on, press the throttle in zero start mode to start directly; in non-zero start mode, the scooter needs to be coasting above 5km/h before it can be started.
P7: Speed Limit setting: range 0-100 percentage speed limit. 99 is to cancel the speed limit setting and ride at the normal speed of each gear.
P8: Hibernation time setting: 0, no hibernation; other numbers are hibernation time, range: 1-60; unit minutes, default 5 minutes; By default, the scooter will automatically shut down if there is no operation for 5 minutes.
PA: Start Strength Setting, which is the starting drive strength when the throttle is pressed after switching on: range 1-5. 1=min, 5=max; default 5.
The default setting for both the Kirin G2Pro and G2 max is 5. You can adjust this setting to suit your needs. If you feel that the start-up force after pressing the throttle is too strong, you can adjust it downwards.
(Assuming that the current Start Strength is 5, the scooter will go from 0km/h to max speed in 5 seconds. If you adjust it to a different value, the process will take longer, to 10 seconds or something like that. (These times are not actual, just an analogy))
PB: Brake Strength Setting: default 0, No Adjustment is required. (because the kirin G2Pro and G2 Max both models are disc brakes, and the main braking is still controlled by the customer himself by pressing the brake lever)
PC: ODO clear. Unrecoverable after being cleared. 0 - The mileage data is maintained and not cleared. 1 - The mileage data is cleared and reset to zero. If set 1, automatically exit the parameter setting page, and clear the mileage data, which cannot be restored.