L200/Triton 4D56 Snapped Timing Belt And Rockers repair (part 1)

Рет қаралды 5,601

Antonio’s Backyard Truck Builds

4 жыл бұрын

Replacing broken cam belt and rockers on 4D56 engine for less than £100

Пікірлер: 16

@antoniosbackyardtruckbuild208 4 жыл бұрын

Three trucks, three different builds. My aim is to try keep my builds and ideas on a budget, to have my 3 trucks to repair/ modify cheaply but safely to then go out and enjoy off roading and touring. Will be adapting interiors to the builds too with pullout beds, cooking areas, awnings etc.... SUBSCRIBE and follow me in my venture of mechanics and modifications to then go out and test it all 😊 Please comments on your thoughts and requests

@adl2005 4 жыл бұрын

Thanks for that really good info. Iv'e met Antonio a few times at Kirton he's really knowledgeable and very helpful.By the way i'm still using the camping stove you gave me - Keep safe till next time fella, many thanks AD

@antoniosbackyardtruckbuild208 4 жыл бұрын

AD L200 Good to hear from you bud Keep safe 👍

@MidlandCoddiwomple 4 жыл бұрын

Hi Antonio. Enjoyed watching your video, very informative. Keep em coming Thanks Dave

@antoniosbackyardtruckbuild208 4 жыл бұрын

barney71642 thanks, it was 30min more detailed but had to trim it down to 15min due to it being too long....hope to be more in detail next time, may be split it into more videos... Thanks for the support Dave👍

@michaelrobinson571 3 жыл бұрын

Antonio, just one question, when you fitted the new rocker arm and rockers did you put a bit of oil on the shaft,I have bought a new one already made up and it looks very dry...

@antoniosbackyardtruckbuild208 3 жыл бұрын

Yes I did, lube it up before you put it in place or it will be running dry for the first minute when you start the engine up. You don’t want it rotating dry 👍

@jsk20006 3 жыл бұрын

Hi my belt just snapped on my L200 just ordered a belt kit and 2 broken inlet rocker arms that were damaged. I know I have to line up the marks on the cam and crank etc but do you have to rotate the cam or crank a certain amount of times to get the pistons in a certain order before I put the belt on? Or if all the marks line up up then am I safe either way? Thanks

@antoniosbackyardtruckbuild208 3 жыл бұрын

Hi, sorry for not getting back to you straight away, busy at work. If you have all the pulleys on the timing marks lined up then pistons and cams will be all lined up, this will be TDC (Top Dead Centre). I will post more when I get back from work tonight 👍

@michaelrobinson571 3 жыл бұрын

Hi Antonio. Robbo here. just wondered if you could help., I have not yet attempted putting on the timing belt or balance belt. Having marked all the timing points the only one not lining up is the crankshaft it stops just about two teeth from the mark. tried rotating it and just the same only this time couldn't move it anymore, pressure seems to hold it. any suggestions would help greatly, tried the net just got confused. Thanks

@antoniosbackyardtruckbuild208 3 жыл бұрын

Hi Robbo, As always this is my opinion and cannot take responsibility for any outcome, worse case would be valve(S) bent/broken stuck stopping the piston moving up and aligning “ top dead centre) from the top inspect the first valves on the front cylinder to see if there is any slight damage ( valves slightly bent etc.) At this point of the crank will not move I would remove the head and check everything is ok there. Unfortunately we are not always lucky and damage happens when belt snaps. As said check valves can move all the way up and are not stuck etc and take it from there. Don’t give up I know you will sort it 👍

@michaelrobinson571 3 жыл бұрын

Enjoyed watching this video, but wish you would have shown a bit more of how to put the rocker am together. I will be attempting the exact same jobs on my Shogun sport warrior 2.7 year 2004, pretty similar engine I think... Anyway very good video and hope too see more...

@antoniosbackyardtruckbuild208 3 жыл бұрын

Hi, thank you for the positive comments. I haven’t posted for a while due to COVID issues, but hope to get back on my builds soon. I had a complete spare shaft and rockers so didn’t have to change individual ones, but there not that difficult/strait forward to swap over on the shaft if need be. Check if your engine is the same as the 4D56t comes only in 2.5lt diesel The 2.8lt diesel is the 4M40 engine and is chain driven. Different counties were exported different engines and specs. 👍

@michaelrobinson571 3 жыл бұрын

@@antoniosbackyardtruckbuild208 Thanks for the feedback Antonio..I will be getting started as soon as this weather breaks. Yes it is a 4d56t...once again . thanks...Robbo.