No video
Lace and True Your Dirt Bike Wheel for the First Time!
Рет қаралды 14,187
Күн бұрынIn this video I walk you through the process of how to lace a dirt bike wheel and true it up! I will be continuing to work on my 1999 Kawasaki KX250 getting it ready to rip! Don't get me wrong, this can be a tough task to tackle, but if I can do it, so can you. Be patient and take your time.
If you decide to grab a truing stand to alleviate a bunch of the stress, pick up the one I use in the video below 👇
🔥www.rockymount...
Grab your next order of parts from RM by clicking on the link below. Thank you to all of you that do! 🙌🏼
🔥Rocky Mountain ATV/MC: www.rockymount...
🔥SOCIAL MEDIA:
Instagram: / greghitchko
🔥EMAIL hitchmotoko@gmail.com with any questions or inquiries
🔥RMATV/MC OEM Parts: www.rockymount...
🔥PROX PISTON KIT: www.rockymount...
🔥MOTION PRO TORQUE WRENCH ADAPTER: www.rockymount...
🔥MAXIMA 80W MTL TRANSMISSION OIL: www.rockymount...
🔥MAXIMA COOLANOL: www.rockymount...
🔥MAXIMA QUICK MIX CUP: www.rockymount...
🔥MAXIMA SUPER M PREMIX: www.rockymount...
🔥RATIO RITE MEASURING CUP: www.rockymount...
****TOOLS****
🔥DEWALT IMPACT GUN: amzn.to/3wQgTl8
🔥DIGITAL CALIPER MEASURING TOOL: www.rockymount...
🔥TUSK STEERING STEM BEARING INSTALLER: www.rockymount...
🔥TUSK CLUTCH HOLDER: www.rockymount...
🔥TUSK CRANKCASE SPLITTER: www.rockymount...
🔥TUSK FLYWHEEL PULLER: www.rockymount...
🔥TUSK CRANK PULLER/INSTALLER: www.rockymount...
🔥TUSK BEARING REMOVAL TOOL: www.rockymount...
🔥MOTION PRO STEERING BEARING RACE DRIVER: www.rockymount...
🔥BENCH BUFFER: amzn.to/3tEmFG1
🔥PRYME CLEANING WHEEL PACK - 8 Inch: www.prymemx.co...
PRYME FIBER FLAP WHEEL PACK: www.prymemx.co...
🔥MOTOSPORT ENGINE STAND: www.rockymount...
CERAKOTE TRIM COAT: amzn.to/3hPfm8P
MUSIC:
EPIDEMIC SOUND www.epidemicso...
This video is NOT sponsored. Some product links are affiliate links which means if you buy something I'll receive a small commission. Thank you for supporting the channel!
@jacobfreese1810 Жыл бұрын
I have had an easy time getting the wheel true until I get the torque wrench out. Some say you need to torque the spokes but I’ve found it impossible to get a rim to stay true if you torque each spoke after truing.
@GregHitchko Жыл бұрын
I'm personally not a spoke torque wrench guy myself. I feel that it throws the wheel back out of true. I just go by feel and make sure they are all tight as the wheel gets trued. Thanks for sharing those same struggles with the spoke torque wrench Jacob
@zealobiron 3 ай бұрын
Some manuals just tell you to hit them and tighten them based on tone
@jimmy_dirtbike Ай бұрын
Hey Greg! Use a baby monitor in my shop as well! Owlette monitor is the move 😂 keeps my baby and I on the same page as I wrench on bikes!
@GregHitchko Ай бұрын
Haha yes!!! You know how it is! We used to use the owlet but have switched to vtech because I wasn't a fan of having the camera on my phone. Too mush going on lol
@jimmy_dirtbike Ай бұрын
@@GregHitchko yeah dude, I feel that! My wife likes the sock part. Maybe I’ll do the same. My phone is chaotic too. I’m 1 week into fatherhood but I cannot wait to start teaching my daughter to ride!!!
@empiresrikesfat 2 жыл бұрын
Yes! Original silver colour looks great, not enough mid range priced silver wheels to choose from for this model bike, Excel here in Australia are $1800 without tyres, there's green and black alloy rims they are cheaper but to common now
@GregHitchko 2 жыл бұрын
Dang that is wild! Didn’t know they were that expensive. Seems outrageous to me
@empiresrikesfat 2 жыл бұрын
@@GregHitchkoThats for set of assembled delivered (only option atm) Excel wheels .. hubs, spokes, rims but yeah expensive.
@GregHitchko 2 жыл бұрын
@@empiresrikesfat maybe I should start lacing wheels for people for cheaper haha dang.
@dr00andrew 2 жыл бұрын
easiest way to get wheel straight is to mark the nipple inside the rim with a sharpie. after all spoked are in the hub and threaded through the rim, put the wheel on the stand and hand tighten each nipple 2 full turns (or until all are the same tension), using the sharpie mark on the nipple to keep track. go around and tighten each 1 a quarter turn. after they have been hand tightened and turned 1/4 turn in, then begin truing it. it is essential the adjustments are made long before the nipples are near the final torque spec
@GregHitchko 2 жыл бұрын
Thanks for contributing that method of truing Andrew! With the sharpie, are you marking every single nipple or a specific one, and then everything is based off of that marked one? Where on the nipple do you mark it as well, I can't quite picture it in my head. Much appreciated dude!
@dr00andrew 2 жыл бұрын
@@GregHitchko i mark everyone on the inside of the rim where you would use a drill to tighten it. its just so i can confirm i am doing a 1/4 or half turn. to help you picture it, most nipples use some sort of philips head on the tube side of the rim, not the side youd use a regular spoke wrench on. its sole purpse is to put a reference mark on it so when i tighten each one, i can visually see 1/4 or 1/2 turn
@GregHitchko 2 жыл бұрын
@@dr00andrew Ahhhh yes! I see what you are saying now. Thanks for clarifying that. I am going to try that technique in the future and give it a shot to see how it goes. Sounds like i'll need a full pulpmx show ready to rock for when I do it!
@HooligansMx Жыл бұрын
Ome thing i also noticed is that tiny tiny tiny little bit you said was good enough at the end once you have the tire on and aired up it can actually pretty much solidify it to where its dead nuts perfect
@ryanphillips727 2 жыл бұрын
Lovin the KX….I’ll be home tomorrow checking dates on my rims on my KTM380, supposed to be all original. We will see. Great videos BTW!
@GregHitchko 2 жыл бұрын
Right on Ryan thanks man, let me know when you find out if the rims are original or not. That would be super cool if they were.
@Hyngyynj 2 жыл бұрын
Good work
@GregHitchko 2 жыл бұрын
Thank you Bobby 💨💨
@Sunspot-19 3 ай бұрын
These are straight pull spokes. The holes in the hub flange dictate where the spoke will go. Try the same with J bend. Now, what cross pattern is the hub designed around? Lacing wheels happens to be a damn sweet hobby. Dirtbike or mountain bike, either are rejuvinating and the only way to take possession of a bike of any type.
@GregHitchko 2 ай бұрын
Nothing like lacing your own wheels that is for sure! I'll stay away from the MTB side of things and leave that to you lol
@Sunspot-19 2 ай бұрын
@@GregHitchko Bicycle wheels have a little learning curve to them since they can be laced in several different patterns. 2x, 3x and 4x. Then we can do a race lace that lays two spokes side by side at the hub. Makes for a stronger wheel that is very elegant at the same time. There are various straight lace type hubs as well however, they are typically 28 spoke. Wheel building is my escape. Really intrigued me with your wheel build video. Dunno if many people can actually do the deed properly these days. Keep it going, my friend!!
@tylerwhelanmusic 3 ай бұрын
Thanks 🙏
@GregHitchko 3 ай бұрын
Hope it helped you out dude! Thanks man
@Nahtanoj65 2 жыл бұрын
Didn't know about the mfg date on the rim, that's pretty neat. Looks like I have an oem 99 on the rear (assuming it is lol), and a 02 takasago on the front of mine!
@GregHitchko 2 жыл бұрын
It’s a pretty cool fun fact right?! That’s rad you’ve got the oem in the rear, and cool to know when the front was made too 💨💨
@Dr_Monster 2 ай бұрын
Use a dial indicator or dial test indicator is you have one
@erickawasaki4351 2 ай бұрын
Hi Greg, I have a kx 125 1996 in restoration. Do you know how to center the rim and the hub on the rear and front wheel? Sur, the rear rim is not in the center of the hub. How to now where I must place the rim compared with the hub? Thanks a lot for your answer. Best regards, Eric from France
@PercyJackson93 10 ай бұрын
What can I do if I didnt measure the offset before removing the old spokes? Do all motorbikes have an offset? I cant find any mention of it in the manual, only the horizontal and vertical buckle tolerances
@GregHitchko 10 ай бұрын
What type of wheel are you lacing up?!
@PercyJackson93 10 ай бұрын
@@GregHitchko It's a triumph street scrambler with disk brakes. Is there anything else I should know? I've been trying to find everything I can online but I can't see much on this topic.
@PercyJackson93 10 ай бұрын
I see that offset is often stamped on the rim as an IS or an ET number in mm but I don't have that either. I do have spacers either side of my bearings so I assume the offset will be 0 and then spacers have been used to position the entire wheel. This is my first time hearing about offset though
@chrisstokley7687 4 ай бұрын
i wanna scream > <
@chaneli4855 7 ай бұрын
😭😭😭😭😭😭
@lawrence6559 Жыл бұрын
p♥r♥o♥m♥o♥s♥m ✔️
@twenty-js1kd 10 ай бұрын
would locktite hurt the spokes?
@GregHitchko 10 ай бұрын
Ehh I would stay away from it and just make sure that you always check the tightness. It's worse when the spokes seize or lock up in the nipple
Partzilla
Рет қаралды 59 М.