The 1st half of this video goes over how to set up an easy engraving. The 2nd half is the machine doing the engraving in case you like to watch
Пікірлер: 104
@brendaellerridenour91353 ай бұрын
Thank you soooo much for taking time to explain how to use a laser so a layman as myself can understand.
@mauricecanney74726 ай бұрын
Great Personality for this! Simple, plain, and like your neighbor is helping you.
@kimmcdowall24762 жыл бұрын
Anthony thank you so much for such great tutorials. I have been learning a Yorahome 3018 with the 5W laser and it's easy to get lost in the immense depth of information about laser engraving but you made this stage so easy I've been explaining it to my grandson (8). I know how much effort goes into creating content and just want to send you gratitude and respect. Thank you again!
@Tilly8507 ай бұрын
Thank you for putting this information in a format that is straightforward. I have a degree in machining, but it's been years since I've used it. Your videos show the program very well and are super helpful to get me going with my laser machine. Best I could find. Thanks for your help. I totally agree with another comment below...saved me a million hours of guesswork and struggle.
@RobNRenie Жыл бұрын
BEST MOST HELPFUL VIDEO IVE SEEN YET .Thankyou so very much , I’m new to laser and after 2 weeks arguing with it was considering getting I’d of it … not now . Cheers
@michaelgranger35232 жыл бұрын
Thank you for doing this video! It saves me a lot of trial and error in learning how to do my engraving!
@chrisperry3525 Жыл бұрын
Bestest easiest most understandable how to video for how to laser/engrave. Thank you!
@peterchamberlain13932 жыл бұрын
These videos are saving me a million hours of frustration. Thank you !!!
@ianjohn8852 ай бұрын
thank you so much man, i have been looking for a good starter video on how to use this software and your video is perfect. thank you soooo much man ill sub and keep a look out for more
@tomasanthony2599 Жыл бұрын
Best tutorial of Laser Gbrl! Thanks you 💪🏻💪🏻
@TheCountryCottageGardener2 жыл бұрын
this was very helpful, thank you for taking the time to film and upload
@neilhay2155 Жыл бұрын
Thanks for the great tutorial. Some of it I blundered along learning a bit, but you have helped me to understand the setup a lot better. Plus now I should be able to understand my results better to make small ajustments when I need to. It took a lot of effort to setup the tutorials you have done, I know because I have setup training before. Great going, please keep it up. i'm running a Atomstack P7 M40, to test the water's.
@dcameron0012 жыл бұрын
Thanks for doing your videos they help us newies a lot
@campfiretrailers28484 ай бұрын
Just what I was looking for! TY
@cdogdillen2 жыл бұрын
Anthony, That was super informative... I just purchased the SainSmart Laser to go with my 3018Pro CNC so this was a wee bit confusing at first... thank you for the break down! I look forward to more tutorials and videos
@cricutcreationswithtory24 күн бұрын
Do you have a video on how to calibrate the laser w lasergrbl. I just got one and formatted the flash drive before looking on it.
@silviaborgers41059 ай бұрын
again thanks a lot for this clear video~!!
@ibrahimvid3 жыл бұрын
The video is very helpful.. Think you
@redliner4965 Жыл бұрын
love the video , it got me been able to engrave on wood within a few hours , as i never had a clue before , my only problem is i cant seem to engrave on glass , i have a sculpfun s9 running on laser grbl , if you could pass me some info to be able to do this , it would be very much appreciated , thank you
@mikethompson9745 Жыл бұрын
Do you have a video on how to add text with a pic?
@GlasairmanАй бұрын
Like you enclosure very much, Do you have a cut list? Looks like alu profile 2020 Hammerhead 5, correct? (In German we say Nut = Groove)
@michaeldora9068 Жыл бұрын
I was looking around and trying to find some answer as to what the unit of measure for the size was and only here did the answer of "it's in millimeters" ever appear.
@MarcRCAddict2 жыл бұрын
That was very helpful thank you mate, would you be able to do a video showing how to do cuts? I want to get as much info as I can before my goggles arrive and I fire up my atomstack p7 laser for the very first time👍
@mrsdizi12342 жыл бұрын
How to make the engraving look deeper into the wood? Thanks for sharing.
@barryleeder9029Ай бұрын
Can u tell me what settings for mirror I got a olm3 10w and trying to do a test card
@Richiebones Жыл бұрын
Hey brother I am trying to figure out how to size the pitcher say I have a a peice of wood that 4 inch by 4 inches I have a atomstack p7 m40
@chrisannoconnor70783 жыл бұрын
Thank you I found this very helpful :-)
@godin82624 ай бұрын
I don't have the import Raster Image when I open and image it place the image direct on work space and the work space change dimension depend on the image I load and it is impossible to move the image on the work space. What is wrong in my set up? I want to figure out why before buying and other software. Thanks if someone could help
@waterlilly62lori6 ай бұрын
How do you know what diode you have?
@joannamclafferty60912 ай бұрын
I close my eyes and see chuy from pawn stars
@brakthehun2 ай бұрын
Maybe I'm him in the future. Ha!!
@thejyhansenergy84249 ай бұрын
How can we cut with this machine
@katrinalylemaglalang84192 жыл бұрын
Hello! Thank you for your videos! Can you please make a video engraving on rubber sheet? Id like to learn how to engrave on rubber sheet for stamp making using grbl. Thank you so much!
@natashavanderberg4220 Жыл бұрын
Hi, I lost my laseraxe software Is it possible to load other software on?
@stylebris2 жыл бұрын
hi Anthony thank you very much for this video. Would you be able to explain how to change to scale for engraving letters and also moving their position , eg if i was engraving a name. Thank you
@mspilgrim Жыл бұрын
Just curious, do you lubricate your belt pulleys. I'm a newbie and mine have started to squeak where the laser moves. Thanks!
@brakthehun Жыл бұрын
Sewing machine oil on my rail carriages. Wd40 inside the stepper motor and in the idler pulleys.
@chelsealeggatt9167 Жыл бұрын
How did you get your image to snap to the bottom left. Mine keeps going to the top right and then I can't figure out how to place my wood in AND it seems to try to go out of my frame 🙃
@kenthomas4479 Жыл бұрын
geez that laser on right makes it aggravating as hell tryin to watch this
@stephaniedaus6284 Жыл бұрын
how to engrave name on pencils using this?
@craigc27212 жыл бұрын
I somehow lost the curser when engraving. I had it for weeks then I noticed today it’s not there. I see it as I hit play then it moves the where it starts engraving then goes off the screen. It’s just nice ti see it even though it’s not necessary. Any help would be appreciated.
@jerrynelson2227 Жыл бұрын
Can you tell me how to prevent an engraved sign from completely fading out from the environment in
@mikecampbell54932 жыл бұрын
Since getting ideal quality, speed and energy settings may require multiple tests, how can you get back to the dialogue boxes to make changes after a test engraving? It seems that once a file is saved, it opens in the "ready to print" window without parameter dialogue boxes reappearing.
@caybeast12367 ай бұрын
Hi, i am pretty new on laser, still learning. does the height of th laser head needs to be adjusted?
@brakthehun7 ай бұрын
Usually,, yes.
@madghostillinois46142 жыл бұрын
Hi Anthony...Excellent video..thanks. I followed along and started engraving a christmas tree on a piece of wood. It was going along ok until the laser suddenly stopped going back and forth and just stayed one position. Of course it just burned a hole through the wood until I shut it off. Tried for awhile to find what I did wrong but could not. I'm using a Ortur Laser Master 2 Pro running the LaserGRBL program. Can you help me find the fix or help me correct what I did wrong. Thanks very much.
@brakthehun2 жыл бұрын
Sounds like your controller board stalled or lost connection. Make sure your power is clean going to the laser and the laptop / desktop
@timesparsenjr74793 жыл бұрын
Hello again, have you made any videos using lightburn? I noticed the laser is more powerful on lasergrbl than lightburn when I use my laser ortur 20w. Ill put the power mode to 80% on lightburn and it will take multiple passes to engrave an image onto a mirror, with lasergrbl it takes one pass at 80%. I know how to change the material selection on lasergrbl which is very helpful, but can’t seem to find that on lightburn. The lasergrbl uses mm/ per sec it is I believe and lightburn uses inches per second, do you know if there is a way to change it to mm/ per second on lightburn? Sorry for the long post, but I’m a newbie and would appreciate any help.
@BenEBrady2 жыл бұрын
Hi Anthony, thanks for taking the time to make these tutorial videos. You mentioned that you would describe how to find out what your lines / mm are for your laser. Like you, I have a 500 mw laser module. Are all 500 mw modules capable of 10 lines / mm or is this something that varies from module to module? Also, I've just built my laser engraver with an MKS DLC 2.1 board with the LaserGRBL 1.1h firmware and I'm using LaserGRBL 4.7.1 software. While I'm engraving I keep getting beeps with messages that say invalid gcode 10:24 or 10:25... Is this caused by some incorrect setting somewhere?
@brakthehun2 жыл бұрын
Typically,, the lower power diodes output a smaller spot and are capable of more lines/mm. A 500mw should be able to do 10 -12 lines/mm
@brakthehun2 жыл бұрын
I'm not familiar with MKS DLV fork of GRBL. That does sound odd that it gets invalid gcode during engraving through laserGRBL. LaserGRBL uses very generic commands to run the engravings. I'll try to research that.
@BenEBrady2 жыл бұрын
@@brakthehun I'm wondering if the gcode command lines are being truncated somehow due to buffer overflow. The board seems to be communicating fine but I'm wondering if the computer is sending data too fast. The buffer indicator is always nearly maxed out.
@brakthehun2 жыл бұрын
@@BenEBrady the buffer should be near maxed out. The fuller,, the better the board can plan movements.
@deanlipska549 Жыл бұрын
How do you import images into the program?
@splinterfingerswoodworking89952 жыл бұрын
My laser grbl is showing a option for constant power or dynamic power can you tell me the difference between the two
@brakthehun2 жыл бұрын
The laser head has to slow down to a stop before moving in the opposite direction. The slower a laser moves the darker / deeper the engraving. ME - you will get darker lines at the edges of your engraving because the laser stayed on the full power even though it slowed down to change directions. M4 comepnsates for a slowdown. It dims the laser accordingly on a slowdown so the engraving still looks even.
@396WAGN3 жыл бұрын
Can you tell me where you purchased the lid for your laser?
@brakthehun3 жыл бұрын
I made it. The lid part of the series is coming soon: kzfaq.info/sun/PLJJWXVM5tQNrYepktUgIUHsHOEdqkOILO
@anitanies35712 жыл бұрын
Hey Toni, my GBRL software turns my image up side down and flipped. How can I make that right again? Please can you help?
@timothycross48152 жыл бұрын
Maybe 6:50 in the video can help.
@syedaliasad90633 жыл бұрын
Hey toni, i just made my Laser engraver, your videos helped significantly. The only problem I face right now is the speed of the machine and the time it takes to engrave. Generally my machine takes around 3-4 hours to engrave. A machine this slow is not good for my project evaluation. What should I do to reduce the time or increase the speed of engraving. Pls reply.
@brakthehun2 жыл бұрын
Try upping your $110 and $111
@626toni3 жыл бұрын
First .Thank you for this great information, what brand is this laser? I want to buy a laser engraver any recommendations ? Thank you.
@brakthehun3 жыл бұрын
There aren't too many bad laser engravers out there. I would suggest something cheap with an 8 bit board to start out with. I design and build my own lasers. Most lasers are designed around 3D printer mechanics which are slow and a bit of maintenance. Mine use high speed automation components which are fast and accurate,, but a little bit pricier.
@ajaved593 жыл бұрын
Great video can you please show how to engraving on the marble I have Ortur Laser Engraver 2
@kenneththorstensen26602 жыл бұрын
Hey Anthony, on the conversion tool dialog box the line to line tracing option is missing .... WTH ?
@brakthehun2 жыл бұрын
Did you load an image or an SVG?? If you load an SVG,, it will only follow the line.
@kenneththorstensen26602 жыл бұрын
@@brakthehun looks like I somehow changed the settings in the dialog box in settings. Made that option go away in the control.
@moderator12373 жыл бұрын
Hi Tony i hope you and your family are doing well, Will you be able to make a video for us how to cut thin wood(board) on 2W laser and with explanation like on this video? i would appreciate it. Thank you
@brakthehun3 жыл бұрын
Sure!! I can explain that. I have a new camera coming in Tuesday so I should be able to do this by the end of the week. Thanks for the suggestion.
@moderator12373 жыл бұрын
@@brakthehun thank you very much. I will catch you soon than :D
@brakthehun3 жыл бұрын
@@moderator1237 I read this wrong. I just made a video on how to cut acrylic. I will do a wood video soon - sorry about the mix up: kzfaq.info/get/bejne/pc2kfphep5atm40.html
@trinovilla96903 жыл бұрын
Hey Toni how are you? I got a good question can we engraved letters by typing them on the lasergrbl program?
@brakthehun3 жыл бұрын
No. You can use InkScape to do that. Use the text tool,, then Export as PNG. Open the PNG with laserGRBL
@audibreeze2 жыл бұрын
What type of oil you are using to finish the wood? Thank you!
@brakthehun2 жыл бұрын
Walnut oil
@timesparsenjr74793 жыл бұрын
Very helpful, thanks. But I am having problems with the sizing, i am trying to do an 11x11 inch print and it keeps changing the size to whatever it deems necessary. Can you help me with this? Also is there way to change the measurements from mm to inches for height and width? I have the ortur laser 2 20 w. I have lightburn and do my prints and cuts from there, I just can’t figure how to get the size I want on lasergrbl. I’m just a beginner, any info would be greatly appreciated.
@brakthehun3 жыл бұрын
LaserGRBL is made by a guy in Italy where only metric exists. It looks like he does plan to add inches to the program eventually. I use 25.4 all the time. inches * 25.4 = mm. mm / 25.4 is inches. 11 inches * 25.4 = 279.4 mm
@timesparsenjr74793 жыл бұрын
@@brakthehun ahhhh, thank you so much!!!!!
@syedaliasad90633 жыл бұрын
Hey Toni, hope all is good there. I am making quite a similar project in my final year of engineering. I can't figure out how to connect my CNC controller board with this software. Do I need to dowload Arduino software too along with grbl software. Pls comment.
@brakthehun3 жыл бұрын
I have a series on programming and connecting your controller board. You don't need Arduino but if you want custom features,, you'll need Arduino.
@syedaliasad90633 жыл бұрын
@@brakthehun can you pls attach the link of that series here. I have CNC board with arduino nano attached with it.
@mikecampbell54932 жыл бұрын
Thanks, Tony. I'm a newb, but this and other videos of yours are helping a lot. Couple of questions for you: 1. In the material DB, there isn't a Sculpfun S6 Pro, only the S6. Also, I'm trying to engrave on birch, but only see "Solid wood" for Sculpfun engraving. When I use the settings for solid wood (Speed 1500mm, Power 50%), the engraving is barely visible. What should I change to get a better engraving image? 2. If I stop an engraving, is there a way to cancel/delete that job and go back to the start or do I have to close it all down and reload the program and image each time I want make changes? Thanks for your help!
@willimanfreeman232 жыл бұрын
How do you use this program with the y axis rotary roller.
@brakthehun2 жыл бұрын
Move the y axis to the rotary. Unplug the y axis motor and plug the rotary motor in that slot
@willimanfreeman232 жыл бұрын
@@brakthehun do I disable the homeing with 0. I move the laser to the roller how do you line everything up with it.
@brakthehun2 жыл бұрын
@@willimanfreeman23 $22=0 to disable homing. You may need a jig or outline to line things up.
@brakthehun3 жыл бұрын
S-Max - Type $$ and hit enter in to your console $30 is your XMax
@alpscraftshack5992 жыл бұрын
How do you ABORT a job that is engraving?
@brakthehun2 жыл бұрын
Hit the red stop button. Not the pause button.
@alpscraftshack5992 жыл бұрын
@@brakthehun Thx for responding & for your promptness. Wish more were like you. Found your LaserGRBL videos very helpful.
@mariajohnston21473 жыл бұрын
if I use Imag-R and edit it there do I have to do this as well?
@brakthehun3 жыл бұрын
If you use imag-r,, don't mess with the brightness / contrast. You will need to make sure your engraving speed and smax are correct though.
@mariajohnston21473 жыл бұрын
@@brakthehun what is smax ?
@brakthehun3 жыл бұрын
@@mariajohnston2147 that's what I meant. On your console,, type in $$ Then look at what $30= and that is your s-max. It's the value that tell your laser to be fully on 100%. I think by default,, it is 1000.
@howiefeltersnatch25962 жыл бұрын
How do you do text in grbl?
@brakthehun2 жыл бұрын
LaserGRBL does not have a design side. I would suggest using Inscape (free software) and creating an image with text from there.
@howiefeltersnatch25962 жыл бұрын
@@brakthehun thank you
@bharamurayar30253 жыл бұрын
Control your breathing
@afufproductions60503 жыл бұрын
U could have speed it up
@sikyist2 жыл бұрын
im just getting into lasercutting. i like your videos, but the heavy breathing almost made me quit watching.
@syedaliasad90633 жыл бұрын
Hey toni, i just made my Laser engraver, your videos helped significantly. The only problem I face right now is the speed of the machine and the time it takes to engrave. Generally my machine takes around 3-4 hours to engrave. A machine this slow is not good for my project evaluation. What should I do to reduce the time or increase the speed of engraving. Pls reply.
@syedaliasad90633 жыл бұрын
My estimated time is very long.....pls help.....how can i improve that?
@brakthehun3 жыл бұрын
@@syedaliasad9063 What machine do you have?? I have some blueprints for high speed laser engravers if you're interested. www.thingiverse.com/thing:4699432