No video
Lathe Tool Holder
Рет қаралды 124,918
Күн бұрынI was in desperate need of a new lathe tool holder. This is a three tiered tool stand. Each tier is made of two horizontal pieces of birch plywood. The top piece has holes CNC milled all the way through. The bottom piece has pockets cut out of the plywood to receive the bottom of each tool.
Some of the tools used in this project
DEWALT DW618 2-1/4 HP Router: amzn.to/1TJmFcr
Milwaukee 18-volt Compact Drill: amzn.to/1sj855F
Whiteside Router Bit 1/8-Inch: amzn.to/1NvVwxd
Whiteside Router Bit 1/4-Inch: amzn.to/2bPwUhf
Oshlun 8-1/2-Inch Negative Hook Finishing ATB Saw Blade:amzn.to/1TJmTQJ
FastCap Glu-Bot Glue Bottle: amzn.to/1TJn0vq
3M Peltor H10A Optime 105 Earmuff: amzn.to/1sj80iw
3M Reusable Respirator: amzn.to/2cGwyPL
3M Particulate Filter P100: amzn.to/2bYwhaK
wood turning tools: carterandsontoo...
To see upcoming projects follow me on social media
Instagram
/ frank.howarth
Twitter
/ frankhowarth
Facebook
/ frankmakes
G+
plus.google.co...
@grandmasterb4471 7 жыл бұрын
Frank, if you use transfer tape on the back of your wood, the material you are removing will not move on you. If you don't have transfer tape, regular masking tape will do. Another thing, which you did refer to in your video, is not blowing out the debris. I wouldn't, just for the reason you mentioned, plus your not blowing dust and debris everywhere. Really enjoy your videos, keep up the great work. God Bless!
@danoive 7 жыл бұрын
Why does it seem every comment is a suggestion? Is everyone the critique? Where are the fans. Thanks for another great video, Frank.
@mdbohica 7 жыл бұрын
Just a suggestion for the lathe chips building up. You could cut box-store lexan down to size and screw it to the front and back of all 3 holders, that way you can still see through everything but the chips would just bounce off. Great shop project!!
@sparkyprojects 7 жыл бұрын
One method that the group i belong to use is to cut the holes, but leave a thin layer at the bottom, you could probably set it so you leave paper thin at the bottom then press it out from the rear, tidy up with a slight roundover, alternately as each hole ( or a few holes) is cut, lay something on top to preserve the vacuum.
@MidtownSkyport 7 жыл бұрын
Clear perspex panels on the front would stop the shavings but also let you see where you're placing the tool in the base.
@Gremlins422 7 жыл бұрын
You'd probably still get some chips flying onto the top and potentially down the holes which may be less easy to solve
@Durfit 7 жыл бұрын
Not if it's only on the front, it could still be emptied out the back. It would greatly lessen the need to clean it out.
@jacobpryor5935 7 жыл бұрын
you could leave a 1/2" gap at the bottom of the translucent plastic so you can blow out the shavings, but it would block 90% of the flying shavings from getting in.
@BobBlarneystone 7 жыл бұрын
Why not just incorporate an airjet or two in the acrylic guard, along with a dust extraction system
@jacobpryor5935 7 жыл бұрын
better to just go with a 4" connector for dust collection attachment!
@DarekOrrLivinLife 7 жыл бұрын
I don't get how someone can dislike franks videos?? They're great!
@wolfgangschulze-zachau2422 7 жыл бұрын
I have made myself a tool holder just like that, and your concern is right, especially if the toolholder is right next to the lathe. I resolved this by drilling holes in all the bottom sections, so that smaller shavings will just fall through. Obviously only works if the toolholder is suspended. In your case, I think a blast with compressed air every now and then is probably the only solution. Or keep it out of the way. Or put a cover on (but that somewhat defeats the purpose).
@mattmoore169 7 жыл бұрын
Thanks for showing the whole build process, including the mistakes! Its nice to see everyone is human and things don't always go right the first time. It gives hope to us who watch these videos and are learning. Thank you.
@woodworking7926 7 жыл бұрын
Frank was a master builder , now he's just a good CNC user ....
@websurfer44 7 жыл бұрын
Always enjoy your videos. Three things impress me with your projects. One - rather than measure exactly the first time you like to cut big and size down to exactly. I think this helps to speed up your projects. Too often I've tried to make things exactly from the start which really slows down the process. Two - If it doesn't work the first time, figure out what will. I like that you show us what doesn't work and how you adjust. The real world is full of things that don't work the first time - adjust until it does. Third - safety, when cutting things or drilling things your conscious concern for safety and where things are going to go if something comes lose. Too many videos of "how to" on youtube.com show the person getting their fingers too close to the table saw or drill bit. I like that you have a natural flow and use push sticks and hold down clamps.
@frankmakes 7 жыл бұрын
Thanks, yes everything is 2 steps forward 1 step back, repeat
@chrisg0001 7 жыл бұрын
Frank, your videos are one of the few that I look forward to. Even the simplest projects are intriguing. Thanks for your hard work!
@camerontarry2159 7 жыл бұрын
Frank, I absolutely love your videos, and have come to rely on them in a way. Like a combination of golf and Bob Ross tutorials, your videos have become my go-to for stressful situations - a kind of relaxing and calmly interesting staple of my life where I know that if something is difficult, for at least six to fifteen minutes I can sit, watch you work that lathe, and breathe. Artful cinematography and beautiful finished products. Keep it up - your videos are much loved!!
@grewald123 7 жыл бұрын
I use masking tape on each peice and then use regular double sided tape between the two layers of masking tape, this then comes away clean. It would also hold the loose pieces down. I have experimented with low-tack double sided tape which works OK if they are only together for a short period of time. Great work though Frank I always enjoy your videos.
@Andrew-lg1rd 7 жыл бұрын
A pleasure to watch as always. Regarding lathe chips, have a look at the shower curtain used by The Homestead Craftsman
@drmkiwi 7 жыл бұрын
It is always a pleasure to watch these videos. Sort of amusing / frustrating to see all the hassles with hold downs and bit slippage on the CNC at the beginning, and yep, they have all happened to me too. I'm amazed you are able to make a "quick" workshop project look so neat. Thanks for the video.
@Everfalling 7 жыл бұрын
CNC tip: never have the cut end on the opposite side of the next part to be cut such that the bit has to travel over the work to get to the other part (unless you have enough tabs to keep the part in place at least). so in this case instead of ending the cut on the right it should have ended on the left. then even if the part jumps up the bit will be moving away from it rather than over it.
@blakea.e.1681 7 жыл бұрын
That's a great tip!
@WildmanTech 7 жыл бұрын
This was nothing but trouble! Thanks for showing the troubles because I'm new at this and I learn from mistakes like that. Thanks!
@blueboybobby1 7 жыл бұрын
a thin layer of glue would have been fine to hold the circles down for routing. i use just a little, thin film, of wood glue and use a scraper to pry the parts up afterwards. hope this helps. love your videos and production!!
@hoverluver 7 жыл бұрын
I enjoy the creativity of your videos.
@AndreaArzensek 7 жыл бұрын
Simple and clean, and most importantly - very efficient!
@jmakes3745 7 жыл бұрын
Thanks for showing your mistakes, i think every youtuber should do it, it is the only way you ever learn!
@ManCrafting 7 жыл бұрын
Frank, I love the aluminum handle lathe tools. Such a contrast to the material they are being used on. Of course the video was excellent. Entertaining and educational. What more can you ask for.
@gunterschone8402 7 жыл бұрын
Very nice video, Frank. The tool holder looks great. And when you clean up, you only need to lift it up.
@brucehurlburt7740 7 жыл бұрын
Great video Frank, and isn't it nice to see things clean and organized (even if only for part of a day) And the chips can be blown out with an air hose or shop vac easy enough. Or even vacuumed out. Seems to have a lot of open space to do so.
@ErikAnderson1 7 жыл бұрын
Nice looking stands Frank.
@littlestworkshop 7 жыл бұрын
For work holding glue wood down to some scrap with a bit of newspaper in between, it allows the glued joint to be parted easily due to lack of strength of paper.
@shookings 7 жыл бұрын
"Do things quickly..." "After the fourth attempt..." Smart idea, doing it quickly. Great content as always.
@seanmeenan3550 7 жыл бұрын
shookings lpĺ
@Supe063 7 жыл бұрын
I used a tool holder like this when I first started. I've found that replacing the top piece (with the holes) with a strip magnet works much better.
@davegraham9932 7 жыл бұрын
you could put a small sheet of plexi across each riser to prevent chips from getting in amongst the tools.
@DesignBuildExecute 7 жыл бұрын
Awesome, Frank! Just an idea. Attach them to each other and then skin the front "openings" with 1/8" plywood. Should keep 90-95% of the shavings out.
@chrisscullynz 7 жыл бұрын
Good on you for showing your mistakes. Excellent videos.
@RandomInsano2 7 жыл бұрын
For the CNC fun: most design software I've used (only Easel and Fusion 360 so far) support the addition of tabs when cutting. These need to be sanded off when done, but hold things in place very well while cutting.
@ShaneMillin 7 жыл бұрын
I could watch you make literally anything and it would be interesting. "Oh.. a holder for tools, big whoop." Actually very interesting! Nice work!
@tkotanko 7 жыл бұрын
Comedy of errors off the start but then things fell into place nicely :).. another great video!
@blakecable19 7 жыл бұрын
Frank, can you do a video on some of your shop tools. I'm interested in what you look for with your power tools and more feasible items like power drills, air nailer, circular saw, etc. As well as any hidden gems you have found that most of us would never think about getting. Thanks!
@Regnarrussell 7 жыл бұрын
Frank just a suggestion but maybe next time cutting the whole thing out of the sheet rather than cutting down the strips. This way the vacuum table will have more surface area to hold down. You could even have the machine do a profile pass and cut your dado's too.
@frankmakes 7 жыл бұрын
that sounds like planning ahead. lol. that would have worked better.
@SgtElev3n 7 жыл бұрын
or maybe just use a drill. Nothing against using a CNC but in this case it seems like it's just making things way more complicated than they should be.
@spookje111 7 жыл бұрын
And more time consuming. There is no such thing as "quickly" on a CNC machine.
@Regnarrussell 7 жыл бұрын
Elev3n Frank is learning how to use a new tool. This is a perfect project to learn on and it seems this project provided some experiences.
@btdga 7 жыл бұрын
Truly spoken by someone with no CNC experience. Last week I cut ten of these 7.62x54r.net/MosinID/D0044.jpg out in 16 minutes on my CNC. I'd like to see anyone do that with a table saw, drill press, bandsaw, and any other non CNC equipment they'd like, much less maintain the precision. Granted the cut file was already done, but with traditional tools you still have design and layout work, repeated layout work every time you make a part, not just the first time.
@fergusoddjob 7 жыл бұрын
another thing for the CNC stuff to avoid getting the circles of waste material flying up and getting in the way of the bit you can use bridges kind of like a halve depth bit that the mill avoids so that the pieces are held in place this is really important for doing aluminium but can also help with wood. then after the job is done you can chisel and sand or file the bridge away
@AMBaggs 7 жыл бұрын
If you put a thin piece of plywood on the fronts of each level it will help with keeping the chips out.
@billcobb1930 7 жыл бұрын
Nice work as always. A double row is a very efficient use of space, but, I have had to be careful not to scrape my arm (again) getting a tool from the back.
@frankmakes 7 жыл бұрын
I am wondering about that, i will see how it goes
@makieks 7 жыл бұрын
I have my turning chisels the other way. The sharp end is faced down so I can allways grab from the handle
@billcobb1930 7 жыл бұрын
Making the front row tip down would fix it. Now I more to do. Good thought.
@JayBates 7 жыл бұрын
Simple and efficient. Prepare for the "lathe tools pointing up is dangerous!" comments ;)
@timlaunyc 7 жыл бұрын
I would be more concerned about knocking over the holders in the front while removing a tool from the back. But then, I am a clutz.
@camerazn 7 жыл бұрын
It looks like the tool holders are screwed into the bench, so little danger of that.
@artfulgloves 7 жыл бұрын
I really like how it come out. I definitely need something like this in my shop. Thanks for sharing!
@starkmms1 7 жыл бұрын
Fourth time the charm...your definitely a man of great patience & perseverance. 👍
@CerebralOrigami 7 жыл бұрын
If chips from the lathe become an issue I would add a piece on the right tying the racks together and then a hinge or two to the back wall so that they could be swung out sou they could be blown clean easily. (That is assuming the racks could take the weight of the tools all on one end.) Or keep it simple bring the rack closer to the front of the cabinet then you could blow the chips against the wall and then blow along the wall to get them out.
@brettbenson563 7 жыл бұрын
Great project. I think the easiest way to avoid collisions with cut parts on the CNC is to path the cut so it doesn't travel over a cut part.
@johnbarlow1892 7 жыл бұрын
The problem with storing them handle up (which is safer) is obviously going to be quick tool identification. I wonder whether a labeling system or perhaps even the tool profile engraved/CNC'd near the 'slot' for common tools would be easy or cumbersome. I'm imagining vertical pieces of PVC pipe (or similar) with the ends of the tubes milled to indicate the tool profile for that slot. Seems like a bit of work, but you seem to take pride in clever/artsy solutions. Obviously with a step/end of the tube for the handle to rest on to keep the sharp cutting edge off of the bottom of the holder.
@Scrmnegl77 7 жыл бұрын
Hey Frank! Love your work. I have to say that one thing I really enjoyed about your channel was watching you work through a designs problems with a lot of the normal tools many of us have. When you got the CNC I initially thought, "Ok, he will use it occasionally for things but still looking forward to the same type of content that brought me here." Unfortunately, I don't think that has happened. I feel like the CNC has almost become a crutch and taking away from a lot of the creativity I saw here.
@ScrapwoodCity 7 жыл бұрын
Useful holder, thanks for sharing
@limitededition7521 7 жыл бұрын
I'm agree David 👍
@garyfindley3933 7 жыл бұрын
Thanks. Will be something similar soon
@MDFRESCUER 7 жыл бұрын
Good job.
@MarkLindsayCNC 7 жыл бұрын
I mount pieces like that on my CNC table with masking tape and superglue. Lay a strip of masking tape on the table and burnish it down good. Lay a corresponding piece of tape on the back side of the material, and burnish it down good. Run a line of superglue on the masking tape that's on the table and spray the activator on the tape that's on the material. Press the material onto the table, mating the strips of tape, and apply firm pressure to the material for a few seconds. It holds firmly and is easy to remove. The little disks that flipped up on you will stay attached to the table until you remove them. I've been using this method for over a year and it's never failed me - not once. I have a video on my channel that demonstrates the method if you'd like to check it out. Click on my name and it'll open my channel page. Thanks for all you do, Frank!
@frankmakes 7 жыл бұрын
I have not heard of this method, a little bit of set up but I see how it works.
@MarkLindsayCNC 7 жыл бұрын
frank howarth I like it so much better than double-sided tape. Give it a try - you'll be pleasantly surprised, I'm sure.
@Martinrude 7 жыл бұрын
yes! This method is often used in guitarbuilding as well. (see crimson guitars videos for instruction) It is a great method for avoiding clamps, and clamp marks in general.
@MarkLindsayCNC 7 жыл бұрын
Martin Rude That's who I got it from - Ben Crowe at Crimson Guitars.
@Martinrude 7 жыл бұрын
:)
@kraftybeard4272 7 жыл бұрын
Tool stand looks great! Gotta think it would have been a lot quicker and easier to drill the holes with a forstner bit or a hole saw though
@soldat2punktnull225 7 жыл бұрын
To prevent that chips falls on the tolls, you could put on the right and left side pieces of plywood, to put on top a big piece of plexiglas with two hinches attached witch epoxy or any other glue. Sorry for the bad english.. I'm German :D
@charlesreicks648 7 жыл бұрын
Some really good ideas Thanks
@AdderlyPazos 7 жыл бұрын
Put some plexiglass on the faces of the tool holder to prevent chips from getting in! You'll be able to block it and see what's behind. :)
@terminalpsychosis8022 7 жыл бұрын
Nice experimentation. For actual HOLES, of course, a large Forstner bit and drill press would have been much faster and easier... but hey, where's the fun in that?! Valuable lessons learned that day. Lovin' your HUGE CNControl table setup there. The experiments with vacuum hold down techniques especially. Oh, and the angled end.. awesome stuff from that. The cloud bowl for instance! Wonder when a decent curved protractor-type hold down will happen for the hinge. (hint hint) :) Keep on keeping us entertained Mr Howarth, and by all means, keep having such obvious fun at it!
@walterrider9600 7 жыл бұрын
thank you
@earlye 7 жыл бұрын
I think instead of a vacuum table, Marius Hornburger's (sp?) clamps may be the solution you really need.
@JasonBarre 7 жыл бұрын
maybe add thin ply to cover the front lower open section to prevent dust build up. But then dust would still fall down the tool insert holes.
@BobBlarneystone 7 жыл бұрын
Somehow, I'll get by with a drillpress and forstner bits to do this.
@BJEAKE 7 жыл бұрын
3 pieces of 1/8" plexiglass and brush bushings in the holes to keep the chips out but still be able to admire the tools. :) Then we go to market and make millions. Yeah, I said "we" :)
@surlycanadian 7 жыл бұрын
How about a quick and easy cabinet with wooden sides and top, with plexiglass doors and back? That would provide shelter from the chips while also maintaining the display aspect of the rack and the plexiglass back means that the sunlight from the window behind is minimally blocked. by only the wooden vertical sides and horizontal top. And now that I'm at the tail end of typing out my suggestion I realize now that what I'm describing would have to be an inch or so taller than twice the heigh of your tallest tool so that you could still lift the tool out of the rest for clearance, so probably never mind.
@hunakosdem 7 жыл бұрын
This is peacefulness I am talking about.
@chase_h.01 7 жыл бұрын
Frank, put tape under the wood so pieces dont flip up on the CNC.
@S-K. 7 жыл бұрын
Double sided masking tape works wonders on the CNC! Comes off real clean.
@skags83 7 жыл бұрын
More examples of why you should use tabs when cutting out pieces with a CNC. As in leave little bridges uncut between the work piece and the scrap which you can just carve away with a hand tool later. That way nothing moves in unpredictable ways.
@flyingjeep911 7 жыл бұрын
Try masking tape on bottom of work pice. It'll hold down small parts, just cut down the the paper. Works like a dream, most times
@limitededition7521 7 жыл бұрын
Also you can use it air in spray to freeze the hot glue Jimmy Diresta show tips and tricks with hot glue
@plunder1956 3 жыл бұрын
How about a clear perspex front to keep the dust and chips out, yet see clearly for insertion. Leave the back open to vacuum it out occasionally.
@stephenisbell1749 7 жыл бұрын
Could you put a piece of plexi in the front vertical sections to keep dust and debris out? You could also use a sort of diaphragm in the tool holes to further block any dust. Great video nonetheless (as always)!
@robshamel3210 7 жыл бұрын
or even leather, cloth or plastic drop cloths? be easier to move if something fell behind or in...
@stephenisbell1749 7 жыл бұрын
Rob Shamel Yeah, that's what I thought a first but I thought it would be cool to be able to see the tools.
@eformance 7 жыл бұрын
Put a clear polycarbonate riser on the "steps" so chips don't get into the holder directly. They could still fall through the top, but most will be deflected.
@Volte6 7 жыл бұрын
If you don't want tabs on your cut outs, just have it do a pocket at the depth of the material - it'll obliterate the material and leave a really nice hole, and no risk of cut outs spinning free and causing trouble.
@NeverStopSeeking 7 жыл бұрын
Nice and simple, ready for new lathe chips and dust xD
@Carl4193 7 жыл бұрын
put a curtain around it to keep the chips out
@peterhaughton8584 7 жыл бұрын
nice frank really nice me well I never use a lath as it's no to what I do frank nice video thanks for that frank peter fae Scotland
@TheBigBigBlues 7 жыл бұрын
Maybe attach a front panel to each of the holders to stop chips building up?
@QwertyGrodnoWood 7 жыл бұрын
Да, так значительно больше свободного места. Но, это временно )
@lydashop5746 7 жыл бұрын
Nice job on the tool holder. could you have used bridge on the CNC to hold the pieces down so you would not loose them
@BobKlumpp 7 жыл бұрын
Maybe some 1/8" Plexiglass on the front vertical openings to keep shavings out.
@labrat7357 7 жыл бұрын
I have Mike Darlow design tool rack that does not hold chips from turning, check out his book, "The Practice of Woodturning" but I really want those Carter tools you have. Envy and coveting are not bad things when it is in relation to turning tools.
@grantbaker86 7 жыл бұрын
I wanted to make quick work of the 12 holes so I cut them 4 times on my CNC
@fabianwiesner3007 7 жыл бұрын
Wouldnt it be nice to have the vacuum right next to the drill of your cnc? I feel like the cnc should be something you can let run, while having a beer, without beeing present all the time. I thought of a metal rod, that can be adjusted to match the length of the drill bit. Its not as easy as with a static blade, like on a bandsaw for example, but the flexible cable housing on the cnc kind of solved that problem already. have mercy with my english ;D
@dav1dsm1th 7 жыл бұрын
Would cutting the holes before splitting into strips result in more risk/failures/cost - or possibly less? A larger piece ought to hold down better on the vacuum table - but the flipped circle would still be a problem (but maybe less if the vacuum was helping to hold it down a little). It would be interesting to hear your thoughts about why you started by cutting into strips - rather than leaving the stock as large as possible - for as long as possible.
@WinstonMakes 7 жыл бұрын
This is why I would use a strip of double sided tape underneath the board...
@LeviShores 7 жыл бұрын
I no longer even attempt cutting without tabs for loose pieces. It's always the unexpected ways that it screws up that cause the worst problems. Nothing like sucking up a loose piece in the DC to get caught between the impeller and side wall...
@LeviShores 7 жыл бұрын
BTW... great video. as always. I need to add more lathe tool storage too!
@ALERTua 7 жыл бұрын
you should make a remote stop button i guess
@simonstucki 7 жыл бұрын
looks nice with all the tools, but would it really have been faster with the cnc even if there would have been no problems than with a forstner on the drill press? you can always make machined dovetails (the rounded ones) with the cnc if you want to use it :)
@tvwears 7 жыл бұрын
Could you add a thin MDF/Plywood board to each face so that chips just collect on top of the holders and not within them and below the tools.
@LivefreeanddiyTv 7 жыл бұрын
Looks great, shame it took so many tries 🤓👍🏼
@miguelmax1601 7 жыл бұрын
Goood =) Greetings from Spain!!!
@zakkbeard 7 жыл бұрын
i understand the awesomeness of cnc, but did it really save you time/money to not use a forstner for the main, larger holes? interesting to see the ways a tool like the cnc is amazing, but falls flat in other ways
@MarkLindsayCNC 7 жыл бұрын
I also have a CNC, and I can say that it's not always the right tool for the job. I think I would have gone the forstner bit/drill press route on the holder for the larger tools. On the smaller holder, I'd probably used the CNC. One benefit of having the CNC is that a person could do both simultaneously (drill the larger holes/cups while the CNC was running the other parts,) thus saving time and money.
@bs838 7 жыл бұрын
Agreed...completely excessive and unnecessary use of CNC
@hotrodhog2170 6 жыл бұрын
Maybe Frank just likes to experiment with his CNC to learn more about how to hold stuff down. Hell, if I had a CNC, I would use the shit out of it just to play!
@jcardwell3rd 7 жыл бұрын
Maybe make the bottom part slanted so the chips don't gather?
@megaAL12345EX 7 жыл бұрын
How about making a dust-shoe for the cnc?
@ka7exm 7 жыл бұрын
Hey Frank, outstanding as always. Just a thought while watching the cutouts 2 minutes in on the CNC. Would it make sense to run a thin strip of double-back masking tape down the back of the material? That would provide a little stick for the circles when they are cut free at the end of each cut. Just a thought. Big fan from Beaverton. Happy holidays to your family.
@catzzzvb 7 жыл бұрын
Maybe there is an obvious explanation Im missing, but doesn't this design make it sort of hard to get the tool out? I would think it would be an easier system if you had the blade facing down and have another cross piece with holes that could act as a stopper on the handle (so you don't dull your edges on the bottom of the stand). But I've never used these sort of tools so maybe it's not that difficult as is!
@estinersouza6371 6 жыл бұрын
Magnífico! Onde encontro essas goivas?
@robjones3132 7 жыл бұрын
would plastic between the holders (on the fronts) stop the wood chips
@TheRandog100 7 жыл бұрын
I've been there and done that. I keep pieces from flying out by creating 1/16" "tabs" in Carve Pro, then pop them out after the cuts are done. Not sure what software you are using. Just spreading the love. I always check for your new videos. Thanks for sharing all you do!
@frankmakes 7 жыл бұрын
Yes i have done that, especially when it is the piece in the middle that I want.
@Jono257 7 жыл бұрын
What is with that light bulb in the opening shot? It's HUGE!
@WilliamAlanPhoto 7 жыл бұрын
What keeps the racks from falling over when you aren't totally concentrated on pulling the tool out, and you pull it out half way, and walk away... and then everything is on the floor. Oh... I'm the only one who does that? OK.
@dsquires16 7 жыл бұрын
no, you are not the only one...
@JAvery2781 7 жыл бұрын
4:17 he screws them in place.
@WilliamAlanPhoto 7 жыл бұрын
+Jonathan Avery Thanks for spotting that! I totally missed it!
@MaxMakerChannel 7 жыл бұрын
Having a router piece come lose happend a few times to me. What causes this? How can you avoid it? How common is it?
@skags83 7 жыл бұрын
By leaving little tabs uncut between the work piece and the scrap which you simply cut away with a knife after the CNC is done.
@MaxMakerChannel 7 жыл бұрын
Isaac Holmlund you answered to the wrong comment : D
@richardfarwell6759 7 жыл бұрын
Did you mean "router bit"? Isaac answered for the flying piece of loose routed disk. A router bit comes loose because: it wasn't tightened properly in the collet; the bit is out of round or undersized; the collet is deformed from use or poor manufacturing; the bit isn't fully seated in the collet. I've had this happen to me only once and it was the bit being undersized. Many routers (including the Dewalt that Frank is using) have a collet that pinches unevenly around the bit because it only has a couple of slots cut into it. Take a look at a standard CNC spindle collet or a collet from a more expensive router (Porter Cable 3hp for example) and you will see the difference.
@MaxMakerChannel 7 жыл бұрын
Yes, router bit.
Family Games Media
Рет қаралды 31 МЛН
wortheffort
Рет қаралды 9 М.
Jung DIY
Рет қаралды 59 М.
Handmade Extreme
Рет қаралды 39 М.