Learn how to master ROKR Marble Night City: Step-by-step Assembly Part 2

Рет қаралды 1,589

6 ай бұрын

#marblerun #rokr #assembly #robotime
Learn how to master ROKR Marble Night City: Step-by-step Assembly Part 2.
Welcome back to my channel and let’s continue the journey of assembling this incredible ‪@Robotime‬ Marble Night City step by step.
This is part 2 as this marble run will take quite a while and a few parts to build as it’s intricate and requires a lot of attention to detail.
We are going to continue with the assembly of 2 runs and then the biggest mechanical part of the whole model.
Also always remember to sand every joint and burr you see as this will allow the model to function as intended, and it will also look and feel much better.
Don’t forget to follow my channel for Part 3 of this marble night city run assembly by subscribing and ringing the bell for video notifications here: / @martinsdoeswoodenmodels
And if you fancy adding one of these amazing wooden models marble runs to your own collection, you can find it right here: www.robotimeonline.com/uk/pro... and happy assembly everyone 🙂

Пікірлер: 26

@MartinsAssemblyHaven Ай бұрын

Some great news everybody, the ROKR Marble Spaceport and Night City Link-Up is finally out on Pre-Sale: shareasale.com/r.cfm?b=2573239&u=4069976&m=106192&urllink=&afftrack= I’m rubbing my hand as I can’t wait for it. And make sure you grab yours from the affiliate link above and thank you all and enjoy 😊

@tenderquasar3789 Ай бұрын

dude thank you so much i didnt even realize the tool had a ruler in it

@MartinsAssemblyHaven Ай бұрын

Aahh you’re more than welcome 😃

@telracs747 Ай бұрын

Florida, USA

@MartinsAssemblyHaven Ай бұрын

Love it, Florida looks incredible fun 🙌

@pigno56 13 күн бұрын

Italy 👋

@MartinsAssemblyHaven 13 күн бұрын

Aahh that’s amazing 😃 Went on a skiing holiday 2 years ago and it was absolutely incredible ⛷️

@MartinsAssemblyHaven 5 ай бұрын

How many sleeves did I lose? 😅 Don’t forget to check out Part 1 if you haven’t already seen it: kzfaq.info/get/bejne/m6yPgdVnq82soGg.html and enjoy 😊

@bobb17g 4 ай бұрын

Bob from Scottsdale, Arizona USA

@MartinsAssemblyHaven 4 ай бұрын

Aahh that’s amazing, I hope you’re doing great Bob 😃

@TimeIsTickingBS 5 ай бұрын

We all have a dark hole in the house where the sleeves just disappear in haha

@MartinsAssemblyHaven 5 ай бұрын

You are definitely correct 😂

@lawrenceelliott350 Ай бұрын

Hi. Update. I ordered several new parts and all was well once again. HOWEVER, I'm about to give up on the model. I cannot, cannot, cannot get A11, A12, and A17. You're working on yours at 39:15 in your video. I can get one or two of the three in. It keeps falling apart so I tried supergluing two parts together, but no luck. I'm either going to quit the model or just glue the parts in and see if it works. Thanks for your support.

@MartinsAssemblyHaven Ай бұрын

Hey Lawrence, Ah don’t give up on it as you’ll get it done. And I would just glue the pieces in, but only if you’re 100% sure that the pieces you’re gluing in go in the correct places 😊

@alysia431 5 ай бұрын

Did you finish it? Is rhere a part 3?

@MartinsAssemblyHaven 5 ай бұрын

Hey Alysia, no not just yet, but it should be out this week at some point as I’ve been really busy with work for the past week 😊

@alysia431 5 ай бұрын

@@MartinsAssemblyHaven ok thanks. I'm pretty much finished now. There was an almost impossible part that I wanted to see how it was done. I figured it out 😅 will definitely watch you build it!

@MartinsAssemblyHaven 5 ай бұрын

Aaw that’s excellent, I’m really glad you managed to build it and thank you very much for that, it’s much appreciated 😊

@lawrenceelliott350 2 ай бұрын

Oh, no! I broke my A13, p. 14, section 18.

@MartinsAssemblyHaven 2 ай бұрын

Oh no, that’s unfortunate. It should be an easy fix with some superglue 🤞

@lawrenceelliott350 2 ай бұрын

I have met my Waterloo! Parts A11, A12, and A17 were the beginning of my failure. I had the devils own time fitting them into their slots. Then I broke one of the arms off A13. I fiddle and fiddle and fiddle with these parts when I tried to add the next layer on, they kept falling out of place. I decided I would glue them into place and that turned out to be a very difficult thing to do. In the process, I broke the arm off my A13 once again. I got some into alignment with D3 but they flip-flopped all around and came out every two seconds. As if that wasn’t enough, it all almost fiddling around with them I broke one of the legs off F10. I could glue it back on, but I don’t know its function so I don’t know whether a repair would hold. Is there a way to get replacement parts from someone?

@MartinsAssemblyHaven 2 ай бұрын

Oohh no, I’m so sorry it’s not going that well, fingers crossed it will get better for you Lawrence 🤞 And yes ROKR has parts replacement form that you can fill in and send away, here’s their link: www.rokronline.com/pages/part-replacement So just go to the link and access the form 🙂

@lawrenceelliott350 2 ай бұрын

Thanks. I've placed my order!!! All I have to do now is wait 2 weeks!

@MartinsAssemblyHaven 2 ай бұрын

No problem at all 🙂 That’s a bit of a wait but it will be worth it.

@lawrenceelliott350 2 ай бұрын

@@MartinsAssemblyHaven My first thought was to buy another kit for spares! I didn't.

@MartinsAssemblyHaven 2 ай бұрын

I’m glad you didn’t, that would of cost you a lot more 😬