Some quick information about skidoo 800 crankshafts and identification. For questions, or if you would like info on getting your crankshaft rebuilt, please email snowxparts@gmail.com Thanks
Пікірлер: 34
@scottybogs68955 жыл бұрын
Great comparison. Nice metal table too!
@blackmasta714 жыл бұрын
Awsome video. Thanks for making it. This is the type of info the average back yard mechanic is missing when building a motor. I am currently rebuilding a 2010 600RS and my crank is a fully oiled bearing crank but the parts fiche calls for ISO flex grease. Im guessing I have a different bottom end.
@chadsmith54402 жыл бұрын
That was helpful and thanks for the help
@xplicitmetal Жыл бұрын
Thank you for this.
@Pneumamechanical5 жыл бұрын
Lets see a how to on rebuilding a crank, true and phase
@wheelieking35516 жыл бұрын
I need some advice on how to tell if my crank bearings are bad, never had a snowmobile apart to know. I assume the crank with cylinders off should spin smooth and free right?!
@Recedinghairline1804 жыл бұрын
"inner sealed bearing seem to work well" LOL
@troypassow98475 жыл бұрын
So i have a 2009 skidoo summit 800 hill climbing edtion. Well i know the ptex cranks suck so i was wondring can i put a etek crank in and if so what do i need to do to make it work. Thanks
@jonellamartinez11825 жыл бұрын
What if you pushed in the little plastic in the crankshaft when try to take off the flywheel need help please??
@snomanz4403 жыл бұрын
Would a 2009 800 crank and pistons work in a 2008 800 engine or would the timing be off like explained on the Etek? I know the flywheel from the 2008 would not work.
@JeremyBrightenburg5 жыл бұрын
Can I change flywheels to update to make work
@michael_j_hopkins3 жыл бұрын
Wanted to buy some rods off you guys. Can’t seem to find a web site. Where could I find that ?
@vailguy99 Жыл бұрын
You can't do the snow x rods on an 850 correct? Cause only brp can rebuild them?
@kenhmful Жыл бұрын
I like the old rotax 583,643 and the 670. Use a rotax 670 in my old yamaha, but i have taken out 4 or 5 conrod bearing on the mag side. Oilpump delite, aprox 1:32 oil mix in the gas, flatslides and short intake, tunnelporting and just a little work to the cylinders, never figuerd out why killing the conrod bearing mag side. Got my hands on one rotax ptek 800, but thats not what i want in my exciter, want a 670 if i figure out what couses t mag problem..
@rockymountainchainsaw Жыл бұрын
Yeah those older 617, 643, and 670 cranks are great. Not sure what is causing your mag side failures. Those Rotax cranks usually take a lot of abuse before they fail.
@brentgoodkey30673 жыл бұрын
well the 1992 mach one had to swap the whole crank none of it was rebuildable coming from the dealer had to exchange the origional crank for a new crank complete. that is interesting that a crank can be pulled apart to repair
@kenhmful Жыл бұрын
Are u shure. I beleve they are rebuldable, looks a lot like the 670 crank, 670 can be rebuilt, they even put 2 cranks together and make a 4syl out of 2 rotax 670 side by side. Dont knowe for shure witch type off crank cranckshops tripple rotax 670 based race engine has, also has 4syl race engine. One 4syl crankshop race engines has been in norway aprox 15years, 2000cc 2t engine, ive prepped the race track for em to do their first testruns, it blew 1drivebelt each 1/8 run
@actZR9003 жыл бұрын
Looking at an 03 mxz800 renegade (pre rev chassis) is this motor known to fail crank bearings?
@kadenreynolds31373 жыл бұрын
no
@otahu265 жыл бұрын
Who makes the better Crank. Polaris, Cat or Doo? Whats the advantage of each and Cons?
@dirtyfacegeorge99384 жыл бұрын
Polaris 850 best crank in the biz
@mikeversluis1347 Жыл бұрын
Yamaha makes the best crank
@lesbouma96662 жыл бұрын
So what’s the life span of these 800s. I’m hearing 4000 miles is about it, then 5K to rebuild them ?
@257Tony Жыл бұрын
I had an 800 HO rebuilt last year, cost me $1800, complete from crank to piston. I pulled the motor, and dropped it off.
@bunsdad4530 Жыл бұрын
When did the isoflex go? Garbage When did they go back to oil?
@aaronmcfee5062 жыл бұрын
Funny how many rebuilds those doo's get
@stuartsanders69493 жыл бұрын
27 bearings
@agfunk11245 жыл бұрын
But what is the reason that those wont keep straight and balanced? I have second 800 etec now with 2600km in it and that f**kin engine is already wobling and jumping around.🤬 They are really nice engines from other parts but that crank..
@Pneumamechanical5 жыл бұрын
Will true & welding keep them straight?
@billwolfe32073 жыл бұрын
just get your crankshaft rebuilt by a professional crank rebuilder and make sure their good cheaper than buying a new one and safer than ordering one on line! or if you have a press and know what your doing rebuild your own!
@mikeversluis1347 Жыл бұрын
They're all the same all those cranks blow out at 2500 miles they finally got rid of isoflex grease they should have been all oil bearings from the start
@rockymountainchainsaw Жыл бұрын
Yes they should have been. Isoflex is a pain. Now we are dealing with 850 crank problems and issues. I have about 50 of the 850 non turbo cranks to rebuild atm.
@canadaplace2be1764 жыл бұрын
Lets not talk. Thats what u do best. Talk us to death. Ok ok yep yep cam ok cam ok yep do that ok. Get s class room
@toddgrant61035 жыл бұрын
Some good info here, but U forgot to mention they are all Junk! Arctic Cat puts real cranks in their engines not disposable crap like BRP. Do a video showing how robust the Cat crank is in comparison. If U know for one that is out of the engine for repair!