How to find what that load rumbling noise when driving is coming from.
Пікірлер: 96
@gaylongraham0774 ай бұрын
She definitely has an insurance policy on him. 😂
@HiFiInsiderАй бұрын
this guy is crazy. no way anyone should do this test.
@saintgtx25 күн бұрын
Completely agree lol I was cringing when he was sticking his hand in there with the wheel spinning at 50 MPH. Your regular Joe Schmo doing this in their driveway will most definitely get hurt doing this
@marvinu_15 күн бұрын
I have a noise that sound like this but not 100% sure. I did the shakedown but no play. I will try to use a stethoscope and run. I agree on the comments about being under the car while doing this test is dangerous in the USA. Not really from a 3rd world country when then do this all the time. You’re a legend man
@J05hFontenot11 ай бұрын
You can just grab the tire at the top and bottom and give it a shake, alternating top in bottom out, top out bottom in. If it moves or it doesn't feel tight, it's going to be play in the bearing. You don't need to do all that lifting it up and putting it in drive. Just jack up one wheel at a time.
11 ай бұрын
Be careful he it's nuts enough to do it while the wheel are running 50 m/hr
@J05hFontenot11 ай бұрын
@ no not while the tires are spinning obviously.
@Pete_Tech_11 ай бұрын
That only works if the bearing is worn to the extent of becoming loose, which is a safety issue. Bearings make noise well before that point. Some people have the radio up too loud so they never hear it, others notice and need it diagnosed 😂
@JJ4207211 ай бұрын
@@J05hFontenotsometimes you need to state the obvious
@J05hFontenot11 ай бұрын
@@Pete_Tech_ they don't always make noise when they aren't loose. I haven't heard a wheel bearing make noise before becoming loose enough to tell with a shakedown. Usually if it's making noise it's because the bearing is worn, and if it's worn, it's usually better the seals have allowed debris or moisture into the race resulting in the play that you feel when you shake it down. I can't think of any other reason that a bearing would make noise. If it's sealed, it's properly lubricated 🤷
@Dawg..... Жыл бұрын
Ya, thinking it's a bearing. Loud noise from front end, louder as you accelerate. Recognize it somewhat from a bearing going in my other car on the highway. Just changed brakes, rotors..think the guy would've noticed it.
@Gserra78 Жыл бұрын
Question i got a 2015 Q50 its got 40,000 miles its making a horrible loud roaring noise when you first start it if its idling not loud when I put it in drive it makes a clucking roaring noise My engine is not overheating it's running normal my gas is normal it hasn't changed gets worst when I accelerate and if I get on interstate And accelerate when I let go I hear a clunk but its a rough drive Took it to infinit told me it was a small leak from the exhaust pipe So I took it to Midas and they did a full exhaust test on it and said there was no leaks they said it could be an internal problem But had my engine and my transmission checked out at infinity and they told me there was no issues with them so I'm wondering what this can be
@Gboogie229 ай бұрын
Thank you so much & great job.
@Pete_Tech_9 ай бұрын
You are welcome!
@greghollinger937014 күн бұрын
Agree, I've seen transmissions completely explode running car on lift.
@williamkeyes31395 ай бұрын
Great Video !!!
@titi7776 Жыл бұрын
Thank you very helpful. I had a vibration noise on a rear tyre and my first thought was rear bearing. Finally it was bad tyre to be changed.
@peterricksugges569812 күн бұрын
Same. Think I have a bad tire. Much cheaper to fix/replace.😊😊😊😊
@docohm507 ай бұрын
Don't do this. You can use a wooden yardstick to stick back and touch the coil and it will pickup the vibration. Ever see a alligator grab a man's arm and roll? One slip and you arm touches that tire going 50 mph and your toast. You can detect a bearing by jacking the car up and shaking the wheel grasping it at the E, W and then N,S grip points. I definitely would not reach in to touch the coil
@Pete_Tech_7 ай бұрын
Tires don’t reach out and bite, but DIYers not paying attention do slip. Happened to me several years back, had road rash on my arm. No it did not send me flying across the shop…slow down with the drama 😂
@matthewcarbone22017 ай бұрын
The average person should NOT reach over the tire while the tire is spinning. Severe injury may result.
@54egg7 ай бұрын
I am almost thinking no one should do that. Could a stick be used to conduct sound / vibration? Microphone..? Great video though.
@Pete_Tech_7 ай бұрын
Yes automotive sethoscopes are by far the best practice, or a very long dense rod like a 24” 3/8 extension. Working around vehicles at all required safety protocols, grabbing the coil spring and avoiding contact with the tire really isn’t an impossible task.
@cosmicallyderived2 ай бұрын
Not impossible but not worth the risk of a disabling injury. Stick a contact microphone on the thing.
@herbert66115 ай бұрын
I had to replace both front wheel bearings and recently bought new tires couldn’t find the right size but was told it wouldn’t affect anything if I bought a bigger size, now when I drive down the road over 40 mph it gets very loud! Not sure what’s going on.
@BryanChance9 ай бұрын
You know, it would be safer if you use something like small, hollow aluminum tube or similar and touch it on the coil spring instead of your arm. LOL We don't want to nick name you "Pete The One Arm Tech" lmao LOL Awesome video, too. Thank you
@thomasjohnson20386 ай бұрын
You mean a projectile lol
@8avexpАй бұрын
Or Lefty.
@static_Tricolor_camry5 ай бұрын
I knew it was my Front wheel bearings, both Front wheels are scraping when I turn Left and Right and the Left side is louder it's making a loud pop when I bring the wheels back straight. I'm replacing both inner tie rods because there's a lot of play in the steering wheel it also feels loose and I'm replacing both Front wheel bearings at the same time. I also need to to an alignment on my Front wheels, because the steering wheel is facing towards the Right when I'm driving. But since my Camry is really low, every shop I called refused to do an alignment on my car so I'm gonna do it myself when I put my Aftermarket wheels back on after Winter.
@lorianpage24694 ай бұрын
Ok, heres a question for you from South Africa. I have a Dihatsu Terios 2012, 1.5 4x4 model that has done 200 000 kilometres both on dust and tar roads. It has been regularly serviced and recently had the front propshaft, front shocks and all brakes replaced, front and back. My question is this: if the car stands overnight and I start it in the morning, I then reverse it out of the carport swinging the rear to the left, I then put it into first gear and drive turning right to get out of my driveway and get this horrible grinding noise across both front wheels and which also makes the noise just under the steering wheel and literally feels like it is coming up the steering column. this lasts for literally a few seconds (60 at most), if driving extremely slowly it continues for longer ggggkkk, gggkkk, almost like dry metal on metal noise and then doesnt come back no matter how long the car moves or stands during the day. It only occurs first thing in the morning when the car has stood for around 12 to 13 hours. The steering wheel turns without any problems. I have had new tyres fitted all round as well. Nobody that I have taken the car to can tell me what is wrong, most of the time they dont believe me because a: I am an elderly woman and b: they cant hear anything, I have driven the car to them so of course the noise has stopped. I have had the car lifted off the ground and driven and no noise, put it back down and the noise will sometimes come back for a second or two. I have been told that the wheel bearings are fine, but irrespective, I will be changing them. My thinking, and I know squat diddly about cars is that there is some sort of lubricant/oil/grease problem that once heated up lubricates whatever is causing this grating/grinding noise. Any suggestions, help, advice as to what could be the cause of this elusive noise (and I am not going senile) would be greatly appreciated.
@Pete_Tech_4 ай бұрын
Sounds crazy but I would try new brake pads and rotors on both front and rear first. Sounds like the brake rotor surface could be rusting or severely pitted attracting debris and cause noise until the pads rub it off enough to not hear it. Unfortunately I can’t diagnose it over the internet. Bearings will make noise constantly if they have failed.
@Mike_Hog_A_Nator9 ай бұрын
I have an 02' Blazer ZR2. Just changed my front bearing hubs because i have a loud "low power steering" type sound that gets louder the faster i go & only makes this sound when rolling. Tires are good & quiet. I think it might be my rear diff bearing. Sounds like the front but the noise drones & sounds weird like sometimes its from the front & sometimes from the rear.
@Pete_Tech_9 ай бұрын
Differential bearings will typically make noise when coasting. (No load applied). Use a lift or Jack stands and drive in the air to find out. And automotive sethoscope is very cheap.
@NewIpsOnly2 ай бұрын
does it causes you to lose speed when the noise happens thats whats happining to me right now
@davidgu16994 ай бұрын
I got my rear brakes and rotors done and its making a rumbling sound as if im driving on the side of highway, took it back to mechanic and they said everything is fine, no issues but it happens off and on at high speeds like 65 70, i have to come to a complete stop and it goes away
@BlackHawk4443 ай бұрын
Same here did you find out what it was
@caffeineman9193 ай бұрын
Same, if I'm coasting at high speed it will happen and only goes away if I give it more gas or coast till my speed slows. Braking, throwing it in neutral does nothing. Pls help us
@Pete_Tech_2 ай бұрын
Sounds like a wheel bearing to me.
@pelonrecords11 ай бұрын
How about if it keeps breaking the belts of the tire on same side. It does make rumblings noise. I'm on my second tire..
@Pete_Tech_11 ай бұрын
That’s not normal, sounds like very cheap tires or an out-of-round wheel.
@yourdentalspa61059 ай бұрын
Can bad upper ball joints on a pick up truck cause a rumbling sound?
@Pete_Tech_9 ай бұрын
No typically it would be a knocking noise 👍🏻
@thesetruths140410 ай бұрын
I had a wheel only make the noise after 25mph. Also had play when grabbing tire at 12 and 6 o'clock and shaking, about 1/16th" play. No noise when braking.
@Pete_Tech_10 ай бұрын
Loose suspension component or potentially the bearing. Would need diagnosis
@thesetruths14049 ай бұрын
@Pete_Tech_ it was the wheel bearing. When I got the assembly out of the knuckle (eventually, was very stuck) it was dry and seemed to be the problem. All other components are tight.
@JTAITSINGER4 ай бұрын
Nope, not putting my hand near the inside of the tire. Got my finger jammed before, and now I think I have PTSD, lol. I’ll just listen for the sound.
@princety-king6827 Жыл бұрын
What happen to the hr type 2 motor ?
@Pete_Tech_ Жыл бұрын
Coming back this winter. Car has been sitting in mt garage torn apart. Been busy with the building construction lol
@RodanX217 ай бұрын
Suspension shot from driving over pot holes..
@A.Loppstirr10 ай бұрын
Around 45/to 50 mph I get a roaring type noise that can only be described by me as the sound of being in an airplane. Making me think it’s just the way the air hits the car… however at higher speeds 70-80 my drivers side tire vibrates and I can feel it in my left foot when it’s resting in that little chill spot (automatic) idk, obviously needs a diagnosis but if anyones knows what that would be let me know pls😅🙏🏻
@shannons.a67299 ай бұрын
I'm having the same issue, did you ever find out what it was?
@A.Loppstirr9 ай бұрын
@@shannons.a6729 still haven’t had time to take it to the shop honestly. I’ll come back to this and let you know when I get it checked out🙏🏻 I gotchu
@pbassassinz80979 ай бұрын
Replace tires first then do the wheel bearing. You can test this by rotating the tires to see if the noise moves.
@longman30499 ай бұрын
Alloy may be out of shape
@kansaswolf8655 ай бұрын
Wheel bearing
@andyb8219Ай бұрын
Hate to see what would happen to my vehicle and garage if the vehicle falls off the jack stands at 110 km/hour speeds.😢
@itsyanielxo Жыл бұрын
Came here to check for the noise in my car but was swept away by his gorgeous face
@Pete_Tech_ Жыл бұрын
🤣 thanks(!)(?)
@A92_ Жыл бұрын
😑
@Antonio-qm3bi11 ай бұрын
What?
@ronald51611 ай бұрын
⏸️
@skabii20411 ай бұрын
Bombastic Side eye
@billyburnett186 ай бұрын
Make sure your windows are down made that mistake b4 the doors auto lock. 😢
@Pete_Tech_6 ай бұрын
Always 😂
@vonniofdoom559010 ай бұрын
That means u got a blown head gasket
@allyesastewart13965 ай бұрын
What if I took my car to a mechanic, they fixed the wheel bearing, and it still makes the noise 😅
@hitpoint37 ай бұрын
Front left tyre on my car, noise only over maybe 100 kmph and the sound is a constant brrrrrrrrrrrr :) coming down under 100 it just dissapears
@allison48107 ай бұрын
No sleeves please!, you may get wrapped up in the tire!!
@Pete_Tech_7 ай бұрын
😂
@steventorres26285 ай бұрын
I don't have that noise I have a whistling noise
@Iwrenchanddetail5 ай бұрын
😂careful where ur sticking those fingers and arms ,making my anxiety go crazy don’t try this who puts a car in drive then starts sticking his fingers and arms all in the wheel now if someone try’s this and gets hurt is it ur fault for showing them this stupid ass shit dude shake the wheel with it off the ground in park no need to do all that shit or take the tire off and check ?😂
@Pete_Tech_5 ай бұрын
I can tell your an experienced technician Forsure 😅
@HASHIRAMA1000Ай бұрын
This guy.....
@Pete_Tech_Ай бұрын
😊
@annaup3733Ай бұрын
OMG..... roflmao
@russellgilbert34538 ай бұрын
Got to get me one of those Hot wives! 😂
@Pete_Tech_8 ай бұрын
😂👍🏻
@madonnarairigh23502 ай бұрын
This is a dumb idea. Don't do what this guy says. Go check out how to really diagnose a bad wheel bearing. This guy is dangerous!