Maddog GY6 Amazon Electric Fuel Pump Install Vacuum System Delete. 150cc or 50cc

No video

Maddog GY6 Amazon Electric Fuel Pump Install Vacuum System Delete. 150cc or 50cc

Рет қаралды 7,696

Mini Me

Күн бұрын

2 to 3.5 gal 28gph pump
a.co/d/aO6iB8s
Rolling Wrench Pump Test • Maddog 150 Mod #7 (Rol...

Пікірлер: 85

@claudeward1693 4 ай бұрын

Been watching you'r content for a while now and learning more about my Gen 1 150cc Maddog , Last night I removed the Makuni vacuum pump , Rolling Wrench is way to pricey on all his stuff and i wont order from them. but thanks to you my Maddog is running better than ever. thank you so much and keep up the great work i really apricate it .

@GhettoWrench 4 ай бұрын

Great to hear and thanks so much.

@nicskeptic 25 күн бұрын

Thanks for saving us so much Time and Money... If the Men in Black show up on maddog scooters then you know who to blame lol.

@dbrhdwk1239 4 ай бұрын

That's a great video. A four-cylinder motorcycle pure fuel pump costs $250 and I'm going to install an electric fuel pump. Great information, detailed explanation, very much appreciated.

@GhettoWrench 4 ай бұрын

Ya these Chinese pumps are still going strong. I would trust one on my car no problem.

@dbrhdwk1239 4 ай бұрын

@@GhettoWrench I live in Korea. Thank you so much for your good intentions.

@christophercraftery8369 4 ай бұрын

Soon as I heard it was being tested in a Floridian meth lab, I subscribed 👍

@GhettoWrench 4 ай бұрын

LMAO

@wesmadebuilds681 8 ай бұрын

Wanted to pass on some info on the pump. The ideal situation would be to have a return system that send back excess fuel to the tank. This would be hard to do without performing major surgery or adding a lot of extra pieces. When the float bowl is full your pump is dead heading against the float needle. On pumps this can be bad cause it will make seals fail and add extra heat. I assume the pump you have is a canned motor pump, which means no traditional seal. Only issue you may have is a little excess heat and possible premature failure of the pump. However, with as cheap as they are that’s not a big deal. In the end no comment to change just wanted to pass this info along. Hope you don’t mind the long winded explanation.

@GhettoWrench 8 ай бұрын

Thanks and I agree 100%. So I would like to make a vacuum pump with it going to a small supply tank and the supply tank would gravity feed the carb. This would solve the issues of vacuum system and be cheap and east. And if you have dead battery you can still get home.

@wesmadebuilds681 8 ай бұрын

Oh, and it says oil but believe it’s a bad translation for fuel.

@GhettoWrench 8 ай бұрын

@wesmadebuilds681 I am seeing that fuel is referred to as oil more and more in "asian" culture. Weird

@ZCRAIZED1 9 ай бұрын

It would be nice to find a pressure switch that could be adjusted to the pressure you want. That way the pump doesn't have to run all the time. Get up to pressure and shut off.

@GhettoWrench 5 ай бұрын

Ya this is weird. first thing I done with no return line

@ZCRAIZED1 9 ай бұрын

I love the idea of a hidden switch also. Someone steals the bike they get down the road as far as the carburetor bowl full will take them. Too funny when it stops running and the owner is beating someone's ass!

@amyhazelvang7198 8 ай бұрын

Sounds like a ghetto wrench sting operation

@androidken 10 ай бұрын

I just threw a 1-way valve on mine and never had this issue since. But great info. RW is a rip off. He claims his stuff is better but he just gets stuff off Amazon and slaps his sticker on it.

@GhettoWrench 10 ай бұрын

I have been pretty happy with everything I have got from rolling wrench. I use NCY Store, RW and other places. Who ever is cheapest after shipping. LOL. I know the 1 way valve is a good fix, but they run so much better with that pump. These things really should be gravity fed.

@ManuelGutierrez-be1ci 9 ай бұрын

So just put the electric fuel pump above the carburetor and it should be fine without any issues correct?

@GhettoWrench 9 ай бұрын

@@ManuelGutierrez-be1ci should be

@seanmayo206 Ай бұрын

Could u reply back Link me to the fuel pump. Not rolling wrench

@jeffkrauss5582 10 ай бұрын

Run a one way check valve and two pumps inline and that helps with fuel to carb

@ZCRAIZED1 9 ай бұрын

Why two pumps?

@GhettoWrench 5 ай бұрын

Only 1 pump. Electric.

@jeffkrauss5582 10 ай бұрын

Great idea I like it❤

@frednetherlands887 2 ай бұрын

Nice!

@trucker132 26 күн бұрын

I just bought a 2 pin "ruckus" fuel pump off amazon. Im hoping that it will work just fine. My biggest concern was it over flowing something. I still dont understand how your pump didnt overflow your glass bowl? The bowl has no lid, so wouldnt the pump keep filling it up and overflowing?? Great video though. Im gonna try and wire mine up and see what happens lol

@GhettoWrench 24 күн бұрын

@trucker132 the floats hanging down from the carb into the glass float up as the glass fills. Those floats are connected to a rubber tipped needle looking thing that blocks the hole the fuel comes in. When the fuel is burned and the floats drop down the hole opens up.

@grudzien9784 5 ай бұрын

Oh I’m going to install it on a predator 212 in my sons go kart.

@baxdesign 4 ай бұрын

Good vid; Can I assume that has been working fine for the 5 months since it was installed, eg no flooding, overflowing, etc issues?

@GhettoWrench 4 ай бұрын

No issues at all. Everyone runs them. All those quirks and issues seem to go away. Makes the bike way more reliable

@baxdesign 4 ай бұрын

@@GhettoWrench Great to hear :) :)

@christophersherratt7299 4 ай бұрын

Petrol electric pumps all perish think the one's that last longer are with seals made of Neoprene that's why they like using vacuum pumps I would fit a one way valve would work better leaving carburettor full then when bike running plenty time for vacuum what do you think 🤔

@GhettoWrench 4 ай бұрын

Ya I never even thought of the valve until it was too late. LOL. I still have 1 bike on vacuum and have no issues with it. I had to put electric on the nitrous one as it is a wet system and needs to spray fuel. But reliability... so far so good. I have hundreds of thousands of miles on my car electric pump but it don't cost $20. LOL

@christophersherratt7299 4 ай бұрын

Wouldn't a decent jet wash car pump give the carburetor enough fuel???

@GhettoWrench 4 ай бұрын

Prob too much fuel and not sure they would withstand solvents and fuel. These pumps are super slow.

@christophersherratt7299 4 ай бұрын

One that supplies clean water for windows

@GhettoWrench 4 ай бұрын

I think fuel may eat up the pump

@ManuelGutierrez-be1ci 9 ай бұрын

Have you had any issues with the electric fuel pump since installing it on the bike? Someone said that it might pump too much fuel into the carb while riding the bike. I just bought the 17303 Edelbrock fuel pump and plan installing it on my maddog scooter

@GhettoWrench 9 ай бұрын

I have 600 miles on the rolling wrench one and about 300 miles on the one in the video with no issues

@geraldlinnearii3357 7 ай бұрын

@@GhettoWrenchmonth later, is the ghetto rig still working?

@GhettoWrench 7 ай бұрын

@geraldlinnearii3357 both the rolling wrench pump and the two Ghetto pumps are still going strong. No issues.

@geraldlinnearii3357 7 ай бұрын

@@GhettoWrench well I'm going to try this ghetto joint first before I drop over $100 on the rolling wrench.

@vincentnavea6999 3 ай бұрын

Is it ok to add a fuel pump if the gas tank is above the carb?

@GhettoWrench 3 ай бұрын

Should be no need for it. Gravity is way faster than electric. But the answer is yes. The pump has no clue where the fuel is coming from. It would still work fine.

@kaochang8401 2 ай бұрын

Its been 8 months now, hows it holding up?

@GhettoWrench 2 ай бұрын

Awesome. Not a single glitch. Except I stole his pump for the 50 to make a video cause I didn't have one. Put a vacuum pump on his. Stupid thing would not start 2 says ago. Finally got it started and went riding then got stuck cause his starter was burned up. That electric pump saves starters. It seems like every time I have brought one of these back in a truck it was because that damn vacuum pump.

@headwaystudio Ай бұрын

My summer semester is finally done and the first thing on the list is getting the chuckus on the road again. I already have under-glow wired into my tail lights, could I still branch another wire off that and run it to the pump? or should I find another spot?

@GhettoWrench Ай бұрын

@@headwaystudio you have a Gen 5? With 12v going to the tail? Should work. Make sure the wire you tap into is about the size of the wire on the pump.

@headwaystudio 26 күн бұрын

@@GhettoWrench yeh, gen 5 with 12v on the tail light. Is that uncommon?

@GhettoWrench 24 күн бұрын

@headwaystudio that's normal. My Gen 5 has 12v DC going to the tail light, but the Gen 1 and 4 do not. They have AC going back.

@grudzien9784 5 ай бұрын

Subscribed. I love shit like this :)) I’m getting a 12v pump as well. I’m glad I didn’t get the pulse one, cuz they are shit and cost about the same.

@ironhead320 2 ай бұрын

You got the fuel filter backwards

@GhettoWrench 2 ай бұрын

I sure did. LOL. Good eye

@ZCRAIZED1 9 ай бұрын

Do you not care for the slide type of carburetor? I see that one has a diaphragm type. I'm sure you know far more than I do so I figured I would ask. Are the slide type not good? I always thought they werre the best option.

@GhettoWrench 9 ай бұрын

No I love my slide type carb. The red bike is not mine. A 28mm flat slide is his next MOD though. I did a video on the 28mm and it made my black bike way better

@ZCRAIZED1 17 күн бұрын

@GhettoWrench Is this one the factory red or burgundy?

@GhettoWrench 15 күн бұрын

@ZCRAIZED1 it's red, but like a 2017 when the red was gloss.

@ZCRAIZED1 15 күн бұрын

@@GhettoWrench Thank you. I just ordered a white one from the Cajun Maddog place. I want a gloss red one also but none are available. I'm building a Honda Ruckus also. So much more that can be done to these frames.

@seanmayo206 9 ай бұрын

Mine starts really with no problem. Its nee but

@denniscongello1908 7 ай бұрын

I have a 50cc QY6 engine. Can I just clean the vacuum line.

@GhettoWrench 7 ай бұрын

Not sure what you mean. If you have a vacuum fuel pump you need those vacuum lines

@default2735 Ай бұрын

Do you have experience using an electric fuel pump on a pwk carb? Mine overflows with a 3-6 psi pump

@GhettoWrench Ай бұрын

@default2735 I have electric pumps on all my PWKs. The pumps are 2 to 3.5 PSI though.

@default2735 Ай бұрын

@@GhettoWrench which pump do you use thats 2 to 3.5 psi?

@GhettoWrench Ай бұрын

@default2735 @seanmayo206 CarBole Gasoline Pump Electric Fuel Pump Universal 5/16 Inch Inlet and Outlet Inline 12V 1-2A 28GPH 2-3.5P.S.I. Operating Fuel Pressure a.co/d/6kqCBO0

@calvinmorris4188 6 ай бұрын

Filter should be before the pump will keep trash out the pump

@GhettoWrench 6 ай бұрын

Ya you caught that. LOL. I put one before and after in case the pump comes apart.

@nicolewolcott 3 ай бұрын

Do you think this would work for my old Intruder 750?

@GhettoWrench 3 ай бұрын

It should.... are you removing your tank? Nothing beats gravity.

@nicolewolcott 3 ай бұрын

@@GhettoWrench I cant gravity feed, seems like the upper carb doesnt get fuel when I try that =(

@GhettoWrench 3 ай бұрын

@nicolewolcott my buddy had the 800. Can't remember if that tank was fake or real and gas was under the seat. Did the bike come with a fuel pump stock?

@headwaystudio Ай бұрын

What size is that red hose?

@headwaystudio Ай бұрын

If its 5/16, did you have to alter the fuel tank port?

@GhettoWrench Ай бұрын

I think it is 5/16" I use those fuel filters that take multiple size hoses in a step down fashion as adapters to go from different size hoses. There is no standard on these maddog hoses and when they get hot and harden over time they start leaking at the areas where the hose is too big for the barb.

@GhettoWrench Ай бұрын

I think the fuel tank takes the bigger hose than the carb. The fuel pump takes even a bigger hose. I use armorall or soap and force the smaller hose on those.

@headwaystudio Ай бұрын

@@GhettoWrench So I'm all hooked up but I can't get these air bubbles out of my line. My keihin doesnt have a drain screw like the stock cvk did

@GhettoWrench Ай бұрын

@headwaystudio the keihin had those tube's coming out the too for overflow and those are to holes in top of the float bowl. The pump should push fuel in the bowl and the air should go out those tubes. So it shoukd work. My lines never look full of gas and always appear empty.

@grudzien9784 5 ай бұрын

Hey brother AWESOME video