I believe he has a 5.8 final drive and the clutch is 5,5"

@@andyc3080 you mean the the final drive-pinion? That only works when the machine is moving.

There is one on my channel :)

Thanks mate really appreciate it :) Sounds like a good idea the r3 looks so good.

@@snowsaysahhh3037 i do like the r3, its a bit of an upgrade to the standard model, but there are some nice bodykits available. question for you, are you mapping the ecu your self or do you have a tuner do it for you ?

Yes look on my channel i do all the ecu mapping myself with verstuner.

200 ci catalytic converter + TRC Exhaust

Yes it is :D

2,2kgs without the friction plate 2,4 with it

Its in the discription of the video :)

No there is a specific counterweight for it

@@snowsaysahhh3037 I thing that it is just a waste of money and a thing to make you pay for. The flywheel has to have nothing to the engine internals balance, the engine combined with the counterweight has to be balanced itself without any use of a flywheel. Thus I mean the stock counterweight soud by used with any type of a flywheel. I know there are companies selling flywheels with a "special" counterweight for their type. In other words that would mean that the original flywheel is ouf of balance and with use of a specific counterbalance you get it balanced. And that would be the same with the new setup. Why would they make ouf of balance parts, combining them together to be balanced? Even those iron flywheels must be out of balance when made, each one is different, balancing them additionally. None of them would be the same, to fit random counterweight. They are just balanced at the time of their make. Then imagine revving engine without flywheel, will it be vibrating and destroying itself ? :D

@@mato424 the rotors are cast balanced, the eccentric shaft is machine balanced, there is a front counter weight, and on the manuals the stock flywheel is thicker on one side (meaning the balancing is cast into the flywheel and machined by hand after to perfect) taking away the counterbalance in the rear greatly upsets things, hence why you need a rear counter balance if you go lightweight flywheel

This is with lightweight pulleys lol haha i didn't post the modlist tho

@@snowsaysahhh3037 okay, that's impressive then ;) I have just purchased the pulleys and since I'm not using the AC, I have cut one half of the main pulley off. This way the weight was reduced by another 160g and all pulleys weight together 380g :)

@@mato424 yeah. I wilm post you the video where i wrote the mods i have in the discription :) or ill change the discription of this video when im home :D

Probably the same as before maybe a bit better since the engine has to work less but nothing major. I'll give you an Update next time i fill up.

and i have 04 port with 5 gears does it work on my mazda??

@@alanalmeleji125 Nope doesn't work on 5 speed

​@@snowsaysahhh3037natürlich, wieso auch nicht?

I will make one.

you should really take a look at my yt saves quite a bit of time

nah they are fine, i spoke to them just recently and they said it's healthy to give them a spin :D

@@snowsaysahhh3037 Hello! I am interested in tuning my own rx8 with versatuner, and I was seeking to learn as much as I can from the reflash process and all. I will watch absolutely all your videos and thought that if you wouldn’t mind me reaching out to you if I have further questions🤣😅

@@adrielaquino521 Sure just contact me under snowsaysahhh@gmail.com Ask me anything you want imma try my best to help ya i can also give you my discord if you don't like e-mail delay.

Whatchu mean? Without the clutch?

@@snowsaysahhh3037 just the flywheel with no race clutch.

@@snowsaysahhh3037 stock clutch

@@nicopartell8631 I don't understand why i mean why would that matter? You need a clutch to drive. It would rev faster than with the clutch ofcourse. I showed what happens if you disengage the clutch and that's plenty fast. Only upgrades to do to make it faster is remove the ac compressor and lighten the rotating assebly. But at this point you spend a lot of money just to rev fast and high.

@@snowsaysahhh3037 no its because ive seen lots of other videos with a simillar flywheel but they rev much slower.. So i was wondering if it changes with the race clutch

I really wish i could understand what that comment means but unfortunatly i don't

он поставил легкий маховик и диск сцепления + как и положено поправил карты в ECU. теперь обороты набираются быстро, но так же быстро они падают при отпускании педали акселератора. Другими словами это чисто гоночный сетап.

My own

@@snowsaysahhh3037 Can i ask what ECU did u have?

@@neloangelo808 stock ecu look at the videos i made bro :)

@@snowsaysahhh3037 Sorry bro i dindt get that XD

@@neloangelo808 All good :)

Still NA

nope. guess again

Fuel cut. All 8s do it but the speed this guys does is nuts

Oh you tested that? Or just a guess?

@@snowsaysahhh3037 yeah my first ever rotary flooded and effed the seals coz i drove it like a wally bouncing of the limiter i learnt after that and now i get long life from my rotarys

@@snowsaysahhh3037 the lightened flywheel and twin plate clutch are a great idea though and really help the engines rotational balance which reduces bearing stress. This youtube'r just needs control his right foot a bit better 😄

@@jameshoath83 First of all i don't drive my car all the time till it bounces of the rev limit that was for video purposes only and second of all i have so much oil in my gastank i could open an oilfarm haha don't worry about my seals.

@@jameshoath83 Thanks thanks i came up with the idea myself :D Downshifts are a breeze and 1st gear really pulls hard now.

The Clutch is a "Quarter Master V-Drive 5.5 inch Twin Disc Clutch" and the flywheel is from mazdatrix "race flywheel for 5.5" clutch turbo + rx8" i got mine not from mazdatrix tho. i got mine from a friend of mine who owns a rotary shop so that's all the info i can give you. if you need help maybe add me on discod and i will send you the specific links and i can help you with software since you can't run that combo on a stock rx8.

@@snowsaysahhh3037 Whats the input shaft specs?

@@azure3182 It should be 1x23 spline

@@snowsaysahhh3037 I can’t find one with that input, do you have a link?

@@azure3182 www.mazdatrix.com/product/clutch-race-5-5-5-5-v-drive-turbo/

Yes it is

@@snowsaysahhh3037 rx8 forever 😁

The flywheel you mention is almost double the weight of mine lol I have a lot of mods but none of them affect idle. Also my Clutch is twin disc and is like 3,5 kilos I don't get what you mean yours doesn't do that.

@@snowsaysahhh3037 my rpm gage does not move that quickly across the rev range. I am curious to see the power you are putting down to the wheels. Great video I subscribed to your channel.

@@Alpha_Marketing_Boss Ah i see i thought you mean it in like in a bad way because my idle is now kinda trash :D I will post a dyno video soon and i'll do a few accelerations aswell. Thanks for the sub really appreciate it :)