Get the specs on our new engine for commercial applications, the Cat C7.1 as well as key features of the C7.1 for high performance applications. Learn more: bit.ly/C7_1
Пікірлер: 113
@AdvancedUSA4 жыл бұрын
The world misses Cat engines for medium to large trucks.
@dwightlooi4 жыл бұрын
The C7.1's power density and torque is great for the displacement (7.0L), but it is somewhat on the heavy side. The C7.1 HP is about 750 kg. For comparison, a similar displacement and output GM Duramax L5P (6.6L, 445 bhp / 910 lb-ft) is about 400 kg. The same can be said of its Cummins and Ford 6.7L competition in the same power class (400~450 bhp). This may not matter in marine applications, but it matters quite a bit in heavy duty trucks. This largely explains why you don't see Catepillar engines in light trucks. I am sure CAT is more than capable of producing a lighter engine, but it is a saturated market and there may simply not be the financial incentive to enter the fray.
@5.43v4 жыл бұрын
@@dwightlooi it's not a saturated as it used to be because Navistar is gone
@dwightlooi4 жыл бұрын
@@5.43v That in itself was kinda sad because Adv EGR worked in the end... but reliability issues and lawsuits from its the premature introduction forced by the environmental extremism of the Obama Administration destroyed Maxxforce as a brand and eliminated an American engine manufacturer while creating an opening for MAN. The point remains though that for CAT to have a 7 liter offering targeted at trucks, it is going to have to weigh like a Maxxforce DT (or whatever Cummins or GM alternative). It can,t be a 1600 lbs engine.
@TATEXPRESSINC4 жыл бұрын
Shoutout from TAT Express out of Hutchins, TX
@delonthomas27726 жыл бұрын
Wish I could get out of my country to travel to these places where these great teachers of technology live
@DuckSongFan2 жыл бұрын
What country do you live in?
@dubblpumper6 жыл бұрын
What can you sat, CAT engineering at its finest! Germany`s MDU also makes some fine diesel engines!
@bongmerced58425 жыл бұрын
MTU or MDU are very expensive to operate specially after sales parts needed during overhauling . its good for military marine special application . compare to CAT engine are design for many purposes , either military, comercial fishing , pilot boat and fast craft. Both are continueos running engines .
@nof-bdybs69486 жыл бұрын
Gear drive EVERYTHING!
@Ollitopay6 жыл бұрын
I'm sure they're worried about stuff locking up, but yes I agree. Even phenolic materials can take a lot of torque and break if they need to.
@emiles55495 жыл бұрын
This guy has probably the best job on earth
@fahemhamou6170 Жыл бұрын
تحياتي الخالصة شكراجزيلا من الجزاءر thank you very much
@Seankamrath4 жыл бұрын
makes me want to go back to school and become a marine diesel technician. I absolutely love these engines.
@richardrcgoncalves27206 жыл бұрын
O motor c7 tem problemas com o tacho, eu já fiz 3 serviço aonde o cliente teve de substituir o bloco do motor devido essa falha
@Darkmatter21346 жыл бұрын
So when this coming to the Truck Market?
@_chevyavalancheG3 жыл бұрын
I wish they made cat engines for heavy duty truck's
@salvatorebasile70565 жыл бұрын
Proud owner of 3126 Cat very realiable and easy to maintain. 6000 hrs of operation and still going strong.
@thevikingwolfpack8366 жыл бұрын
How bout you guys work on putting them back in trucks.
@Rob_Moilanen6 жыл бұрын
CAT shouldn't have ever gotten out of OEM powering commercial OTR trucks, it'll be tough for them to get back in, they've lost too much market share to Cummins and Detroit!
@tommyw.94245 жыл бұрын
Well of course they lost market share, they left the market. Detroit isn't much to worry about, since they're Daimler only now. The only competition is Cummins and all of the new OEM brands. I hate the new vertical integration of trucks. Used to be you could pick a truck you want and then get it set up with the engine you want, transmission you want, and so on. Now every single truck update brings more proprietary bs.
@michaelpuente33524 жыл бұрын
George Ashing even if they do come back it’s not gonna be the same they’ll probably gonna have the dpf system which makes them junk
@paulpence88954 жыл бұрын
Gov juice, ruined the entire farm and trucking industries.... Why the F do farm tractors need to be T4F... I quit farming 20 years ago, but every one I still know that has a truck with a 3406, it's their favorite truck...lol...
@Tyler-xe1es4 жыл бұрын
They left because they dident want to put all that Def Dpf shit on there engines ! They left as #1 for a reason.
@usmanrai12446 жыл бұрын
Will this fit in my honda?
@youssoufjimraou99644 жыл бұрын
Thanks soo mush
@mtgwdefender5 жыл бұрын
Hey guys! I have a C7 engine family 5CPXH0442HBK with the cylinder head off and the walls on cylinder #3 with some scratches, if not gouges. The original symptoms were huge blowby coming out and blue smoke / oil coming out of the tail pipe. What is weird is that cylinder and head area for cylinder #3 are dry and we found oil on top of the other cylinder / head area. Also, only cylinder #3 exhaust manifold hole is wet of oil and the other ones are dry. Please let me know what are the chances that this engine can be rebuilt, maybe by cutting the walls and putting bigger pistons. Or, what are the margens /specs / limit for cutting the walls. Thank you for your time and effort
@CatMarine5 жыл бұрын
Hi Lorenzo! Your Cat dealer can help! To find a dealer near you visit bit.ly/2VEZnfZ.
@dwightlooi4 жыл бұрын
Power density and torque for the displacement (7.0L), but somewhat on the heavy side. The C7.1 HP is about 750 kg. For comparison, a similar displacement and output GM Duramax L5P (6.6L, 445 bhp / 910 lb-ft) is about 400 kg. The same can be said of its Cummins and Ford 6.7L competition in the same power class (400~450 bhp). This may not matter in marine applications, but it matters quite a bit in heavy duty trucks. This largely explains why you don't see Catepillar engines in light trucks. I am sure CAT is more than capable of producing a lighter engine, but it is a saturated market and there may simply not be the financial incentive to enter the fray.
@justanotheraviator2357 Жыл бұрын
Cat quit on highway engines because of emissions
@atulkrpandey19292 жыл бұрын
tnx
@Yasserflehan197010 ай бұрын
What kind of heat exchanger is install on it
@jamesshanks26146 жыл бұрын
There is an owner/operator I know who has owned and run a 1944 Cat D-8 cable dozer since he bought it surplus for $300.00. Cat has tried many times to sell him a new dozer and he keeps refusing because they went to electric start. His has the donkey starter on it and he loves it as in the winter when it's not uncommon to see -40 or lower temperatures his never fails to start as long as he brings an extra Gerry can of gas with him. The company he's contracted to sent him to level out a new parking lot 12 years ago and while he was finishing up the new to the company 140 grader showed up with the computerized leveling gps system on it and after three passes on the gravel that had been leveled by the dozer operator called the owner and told him he was wasting his time out here as the dozer operator had leveled the new parking lot dead on spec simply by back dragging the blade on his dozer. The operator of that old D-8 is still working today at 87 years old and says why should I retire? I enjoy running a dozer. One morning someone will show up on a job and find him dead at the controls on his D-8. He's a cranky cigar smoking grumpy old bastard who has more than once shoved a caterpillar salesmans pickup truck right off the job site if he felt it was in the way. The local Cat dealer generally send their new salesman out to visit him to " break then in properly ". Only one salesman ever returned not with an order for a new dozer but an order for 8 cases of oil filters, fuel filters, and air filters and everybody at the Cat dealer wanted to know how he did it. He refused to tell them. Every time he visited the old timer he came out with two boxes of cigars, the type the old timer smoked, parked the company pickup next to the old timers pickup and carried both boxes under his arm while smoking his own cigar. He and the old timer got along like they grew up together because he never tried to sell the guy anything. Just two boxes of cigars and fresh hot coffee a loaf of bread and four different types of deli meats, mayonnaise and other condiments and showed up on the job just before lunch. Opened up the ice cooler in the back of his truck and started making a big fat sandwich, after making his sandwich he look at whoever he was visiting and say be my guest, make a sandwich I got plenty of fixing. His wife suggested it after two weeks of no sales so he decided to try out her way. You win them over with food and they will buy stuff from you when you refuse their cash for the food. He did this at every job he visited and always got decent sized orders for supplies or parts and occasionally new machines when other salesmen had visited the same companies and got nothing except we'll call ya if we need something. That salesman retired last year and figures he spent $ 100 bucks a weeks to keep the deli cooler stocked for one week but made far more than that in commissions. His wife stacked the cooler every morning with whatever she had just cooked in the kitchen, she cooked about 30 pounds of fresh chicken with potato salad and four large bags of potato chips and the second stop of the day was handed an order for more equipment than he ever sold at one time in his entire career. Just over $2,000,000 worth of loaders, dozers, rollers two water trucks and dozens of other pieces. The contractor while he they were making sandwiches that morning from his cooler got word he won the biggest contract he ever bid on and decided then and there that the kid salesman from Cat never bothered or tried to sell him anything he didn't need was the one to order the equipment with. His commission paid for a new house for him and his wife. The Cat dealer almost had a heart attack when he handed in his orders at the end of the day. He refused a raise because he told the owner why give mea raise when you know my weekly commission will exceed my basic pay but thank you for the thought. He said the following weeks paycheck was double what his basic pay was and the owner refused to take it back. Only for three weeks after he started as a traveling salesman did he collect just a basic paycheck with no commissions then started hauling the ice cooler stuffed by his wife, the cigars were his idea as everybody when he started smoked cigars. There are ways to sell and service grumpy customers. You simply figure out the easiest way to their heart. And don't try to sell them a thing. Old school ways are the best.
@doc.voltold42326 жыл бұрын
James Shanks that's an amazing story. Thanks for sharing!
@bongmerced58425 жыл бұрын
What a story . Old school rocks , D8 dozer with a Petrol feed starting engine on the side is very rare to find now a days . But its good to know you friend still using it .
@18wheels19664 жыл бұрын
Nice story.
@Pythnn4 жыл бұрын
@Ken Sometimes sales doesn't mean pushing to sell, it means working out how the person ticks
@alforgeron1049 Жыл бұрын
Great improvements. I design hulls for fast, fuel efficient, comfortable rough sea operation, and as an engineer. I liked your presentation very much since all your improvements build on the old where possible. Here is why I write. I have another further improved design, for rough sea even greater safety and comfort, and at this time I need engine dimensions, allowing the engine to be lowered further into the run of the hull. I checked the CAT site, but found no dimensions included anywhere. You do wise designs, I notice, so below the drive shaft, where the hull run is, any needless engine feature which if rediced in width would allow mounting deeper. Any change in the mounting rails which can be narrowed closer than your present 28.9" shown with needed vibration absorbing pads, would be a further help. You may know that hulls in rough seas are harder to turn over when the center of gravity is lowered. My hull is really good in bad weather, but I want to try to improve it even more, since it may be used for Search and Rescue. My present 39' design i am working on will allow +40 MPH with your 500 HP C7.1. My 36' fishboat with 270 HP gas Olds 403 marine, pushed the hull to 35 MPH, so my 39' should get +40 with your 7.1. These are real workboats, not runabout hulls. I am located in Bedford, Nova Scotia, Canada. One other reason for mounting lower into the run, is to reduce the height of the engine box and working floor. Your competitor QSB-6 has the drive shaft below the mounts? Your is well abov the shaft. One final thing, my hulls do not have that forward lifte bow but has an attitude of 2-3 degrees at speed, so I tend to have the prop shaft at the same angle as your drive shaft. Your 12 series seem to be aimed in my direction more ? For your info, my 6' hull model of my 36' full hull, was tested smoothly and perfectly stable without exponential power increasing, but almost linear up to +70 MPH. I saw no need to go beyond that speed , but would allow more. I'm getting older, so my present hull design may not be built? Just confirming the urgency. Be safe and keep up the fine work.
@tharungopi537 Жыл бұрын
How to do valves lash for C7.1 marine genset, how much-interval to do valve lash.
@CatMarine Жыл бұрын
Hi Tharun. Your local dealer can assist you. Their technicians are experts with the engines and can understand your specific application and how best to answer your questions. If you need to find your local dealer, you can use this link. www.cat.com/en_US/support/dealer-locator.html? - Cruz
@rosewhite---6 жыл бұрын
Is that Slovenian alternator reliable?
@rearspeaker63645 жыл бұрын
NO,ITS NOT.
@bongmerced58425 жыл бұрын
Its intended to charge the battery and supply 12 or 24 volts to EFI fuel servo valves since this is common rail engine . Starting up also.
@alialalialialali-me9ez5 жыл бұрын
مرحبا ارجو نشر دارة حقن الوقود وكيفية عمل محرك كاتر بيلر في المعدات مثل البلدوزر
@CatMarine5 жыл бұрын
مرحباً ، بإمكان وكيل Cat مساعدتك! للعثور على وكيل بالقرب منك ، قم بزيارة bit.ly/2xQO8an
@juan41303 жыл бұрын
Que belleza
@hectormiguel92014 жыл бұрын
Si hablaste en terminologia de cilindrada, pero no dijiste nada del motor ni de sus componentes. ¿Como interactuan entre si?
@CatMarine4 жыл бұрын
¡Hola Héctor! ¡Su distribuidor Cat puede ayudar! Para encontrar un distribuidor cercano visite: www.cat.com/es_MX/support/dealer-locator.html? - Pablo
@georgegeorgepht4 жыл бұрын
One day they will make these guys wear football shoulder pads and welder helmets along with some deep sea diver suit to make sure they do what OSHA wants.
@robertdivany16273 жыл бұрын
George George..i would like to say that you are exaggeratin a bit but I think that day will come before you know
@johnwolf75234 жыл бұрын
I remember when the marine engines were built in PeoriaIllinois, but maybe these are Perkins in disguise. I could be wrong but you never know.
@electric74873 жыл бұрын
The small engines (4.4L and smaller) are the rebadged Perkins engines (Cat bought Perkins for those engines IIRC). The C7.1 and larger, at least, are true Cat engines.
@MississippiMudMX6 жыл бұрын
I miss the 3408
@Yasserflehan197010 ай бұрын
What is the difference between C18 and the this model
@CatMarine10 ай бұрын
Hi Yasser! Your local Cat dealer can help you with your inquiry. Could you send us a direct message with your name, email, phone and location? We'll reply and connect you with your local dealer. You can also use our online dealer locator: www.cat.com/en_US/support/dealer-locator.html?. Thanks! - Luis
@18wheels19664 жыл бұрын
Not overly impressed by those torque/ rpm numbers. With that displacement and possible re-rate options, may advertise something a little more attractive.
@drozangue17983 жыл бұрын
how much?
@orlandokelly4184 жыл бұрын
I new some help geting an engen running
@CatMarine4 жыл бұрын
Hi Orlando! Your Cat dealer can help with the engine! To find a dealer near you visit bit.ly/3efyNEX - Adrian
@theaveragejoestinkeringand44074 жыл бұрын
How about the next video being meet the new c15 truck engine! If they can make a marine engine why not a truck engine?
@paulbonn90084 жыл бұрын
Different emissions ratings. Truck engines must meet Tier4 FINAL ratings and CAT can't meet it, but so far CUMMINS, PERKINS, KUBOTA & MTU can.
@Tyler-xe1es4 жыл бұрын
@@paulbonn9008 CAT dont wanna make it. They dont want there name slandered by all this DEF DPF bullshit.
@paulbonn90084 жыл бұрын
@@Tyler-xe1es All the DEF components are manufactured by BOSCH. It's cheaper to just buy a company and put the CAT emblem on it.
@5.43v4 жыл бұрын
@@paulbonn9008 how come cat has a C15 tier 4 final website www.cat.com/en_US/products/new/power-systems/oil-and-gas/well-service-engines/18437586.html C15 ACERT™ (Tier 4 FINAL) | Cat | Caterpillar
@paulbonn90084 жыл бұрын
@@5.43v Ahhhhhh yes, true. Seen a bunch in the industrial side in the form of Perkins. Seen generator sets with Volvo with DEF but I haven't seen anything else yet.
@christopherclarke24936 жыл бұрын
why is he wearing gloves and glasses to point at an engine?
@blake-green6 жыл бұрын
That's OSHA for you.
@ch.roughhabit50025 жыл бұрын
don’t know mate.
@robertdivany16275 жыл бұрын
Osha bullshit regulation
@miltonjunior785 жыл бұрын
Safety culture!
@konradcomrade48455 жыл бұрын
dumb rules , when there is no risk. When it gets dangerous, You are on Your own!
@ronaldstephens17924 жыл бұрын
I'd like a C7.1 in a BIG RIG😳
@mohmedhosny60942 жыл бұрын
I ask you if CAT make engine for lawn tractor
@CatMarine2 жыл бұрын
Hi Mohmed. Your Cat dealer can help! To find a dealer near you visit www.cat.com/en_US/support/dealer-locator.html?. - Daniela
@kittycatspecialist Жыл бұрын
Perkins Diesel labelled as CAT since 1998 CAT owns Perkins.
@scottbaker10186 жыл бұрын
yada..yada...Put CAT back in the on-highway market...OMG had to edit.The C-7 is a throw-away block..One bore job depending on wear that's it....Tread very lightly take it from a CAT certified tech for many years .Gen-set engine is its safest app.
@tommyw.94245 жыл бұрын
Isn't the C7.1 a completely different engine though? I can't find ANY info on all the new Cat engines, they really like to keep people in the dark.
@javierg.a48885 жыл бұрын
lo siento no entiendo nada
@rashid4u096 жыл бұрын
😱😱😱
@rodleypumpkins41746 жыл бұрын
You guys are fuckin animals. Keep it up.
@christopherclarke24936 жыл бұрын
is this engine that bad that it will explode while not running?
@ghalebserhal62705 жыл бұрын
Uuu
@18wheels19664 жыл бұрын
Mmmmmmay be. We'll see.
@kannanravikumar25322 жыл бұрын
Price
@CatMarine2 жыл бұрын
Hello KANNAN! Your Cat dealer can help! To find a dealer near you visit www.cat.com/en_US/support/dealer-locator.html?. - Brad
@viltermewendy5 жыл бұрын
Je veux apprendre la bas !
@timtaylor16256 жыл бұрын
All this new tech but still cant figure out today's emission standards. Haha
@46rambo49 Жыл бұрын
hope to hell the C7.1 fixed all the major problems the C7 engine.
@jamesmackinlay44774 жыл бұрын
OK we want them for trucks just make it so we can take off the epa crap easily without going to the dealer or buying a kit of some sort let us deal with the rest.
@asgrides44994 жыл бұрын
Not one engine was started this day
@cesarsirino6456 жыл бұрын
J
@ernestrhoades51474 жыл бұрын
There are way to many hose connections on those engines ,this will make it a knight mare for engineer's on boats ,ever try to change a short coupled hose in in the bottom of a boat?
@alvarogeorgenobregeorge694 жыл бұрын
I think this engine it's a perkins rebadged as cat.
@electric74873 жыл бұрын
That's the 4.4L and smaller Cats. Cat brought Perkins for the small engines.
@gailyoung99115 жыл бұрын
Definitely not running a garbage k&n air filter on a 50k dollar cat engine. Thing would be dusted in no time.
@prevost86865 жыл бұрын
There is no dust in the marine environment. They are marine engines not off road earth movers.
@5.43v4 жыл бұрын
@@prevost8686 salt
@BeingMe236 жыл бұрын
It too bad they got cheap and didn't use a electric water pump. It would reduce parasitic drag which reduces fuel use, increases hp and torque. Gear driven does the opposite.
@raymond80hr6 жыл бұрын
i would say that gear drive is 10x the cost as electric pump and 10x the life electric pump are fine on a car not a big boat.
@02Franxx5 жыл бұрын
Cheap is the opposite, It costs cat more to put a gear drive pump in rather than electric, the parasitic drag is extremely little but what you get is much higher life and reliability
@papabits57216 жыл бұрын
lobby fishing are you sure?
@gw499522 күн бұрын
i have this engine in my boat new in 2022 it Sucks i would advise anyone not to buy this engine !
@aaronarmstrong48443 жыл бұрын
If you're wondering whether you should repower an older CAT engine with this, don't. Rebuild what you have, the C7.1 is an unreliable POS
@electric74873 жыл бұрын
What problems have you seen on the 7.1?
@imbatman9176 Жыл бұрын
Yea what kind of problems are you running into..? I'm thinking of changing my 3208 with 25000 hrs on it with the 7.1