Mercedes-Benz M274 Engine Diagnostic & Maintenance Guide (Mercedes W204, W205, W211, W212, & More)

Рет қаралды 71,237

Күн бұрын

►The Mercedes-Benz M274 engine is a departure from the straight-six or v8 engines that Mercedes has come to be known for. As with most companies chasing higher output and higher fuel efficiency, Mercedes has joined the likes of VW/Audi in creating a two-liter four-cylinder turbocharged, direct-injected engine.
The Mercedes M274 can be found in models across Mercedes' entire lineup, from the SLK to the E-class, C-class, GLC, and even models with transversely-mounted engines. Some of the most popular models you will find this engine in today are:
Mercedes-Benz C300
Mercedes-Benz E300
Mercedes-Benz GLC300
Mercedes-Benz SLK300
Although not a particularly inspiring engine, it does come with the added benefit of being one that's reliable. With only a handful of potential failure points and fairly basic maintenance necessities, Kyle Bascombe, FCP Euro's Mercedes Catalog Manager, walks you through each, giving you the necessary knowledge to buy or own a Mercedes equipped with the M274 engine.
In this video, FCP Euro's Mercedes Catalog Manager, Kyle Bascombe, covers all of the topics, including:
00:00 - Intro
02:25 - Mercedes M274 Air Filter
02:55 - Mercedes M274 Turbocharger
03:25 - Mercedes M274 Water Pump
03:45 - Mercedes M274 Ignition System
05:12 - Mercedes M274 Injectors
06:40 - Mercedes M274 Drive Belt & Idler
07:00 - Mercedes M274 Cooling System
08:40 - Mercedes M274 PCV System
09:46 - Thanks for Watching!
If you would like to learn more about the Mercedes W205 featured in this video, we have a full Buyer's Guide here: • Mercedes-Benz W205 Buy... or you can visit our W205 hub, here: info.fcpeuro.com/mercedes-w205
If you would like to learn about the suspension that often gets paired with this engine, we have a W205 suspension guide here: • Mercedes-Benz W205 Sus...
#fcpeuro #mercedesw205 #mercedes
SUBSCRIBE: kzfaq.info?sub_c...
Get free parts from FCP Euro:
www.fcpeuro.com/page/lifetime...
Follow FCP Euro on:
/ fcpeuro
/ fcpeuro
/ fcpeuro
www.fcpeuro.com/

Пікірлер: 204

@JeeperZJ 2 жыл бұрын

Wrist pin noise can be detected as the engine is dropping in rpms when revved, almost sounds like a woodpecker. Most common in 2015 models, quite rare for 2016 models. At the dealer level we do a full bottom end rebuild, we replace the pistons, rods and wrist pins for all 4 cylinders. If you're experiencing a squeaky belt and have replaced the idler pulleys and tensioner with no success, back out the alternator bolts most of the way (do not remove them all the way) and give each one a good hit or two with a rubber mallet and retighten....the alternator can be slightly misaligned. No need to replace the engine air filter so frequently either, theres a pre-filter in the intake duct that traps alot of material and the shape of the duct prevents much material from reaching the filter. Mercedes recommended interval is 50k/5yrs and at that interval the filters usually aren't extremely dirty....you can change the filter with your spark plugs. Speaking of plugs, if you want to avoid having the plug boots get stuck in the head, warm the engine up a bit before removal and they'll slide out like butter. No real need to replace coil packs or boots when replacing plugs, only do so when one actually goes bad (easy to diagnose).

@davemerc5852 2 жыл бұрын

I do hear a ticking sound while driving low speed ..aside of that had the car for 4 years and now I have a p052e code, I usually work on cars but I hear I have to lift the left side of the engine to get to the sensor that needs to be replaced is there any other easy ways?

@LynxStarAuto 2 жыл бұрын

The coil boots rarely ever survive disassembly on higher mileage engines. By higher mileage, I mean 60k +. I've tried warming the engine, Heat guns you name it. I disconnect them from the coil body, and the boot is seized in the well real nice! When you pull them out, you will notice the boots are all discolored. Plus MB recommends them as part of a tune up. Also, in dusty ass south Florida, you ain't getting 50k out of an air filter out here. It will be filthy after 20k.

@twoc400s5 2 жыл бұрын

I've found at least a dozen documented cases online of 2016+ m274 engines having piston #1 failure at the ring lands. The wrist pin / piston cracking issues is definitely NOT confined to early motors.

@NotYet8 2 жыл бұрын

Would you recommend keeping a 19' W213 E300 with an m274 engine? Do you think these engines can hit 150k miles without any serious problems?

@twoc400s5 2 жыл бұрын

@@NotYet8 nope

@nasmalekzai1945 Жыл бұрын

2017 E300, purchased with 20k miles on it. Went to Costco for shopping, walked out and car misfire like crazy. The Benz dealership is across the street from the Costco. Literally had them tow it across the street because I shut it off right away and refused to turn it back on. They had the car for 2 weeks. RINGLAND at cylinder 1 had failed. Not wrist pin. PISTON RING BOYS. Motor was removed and disassembled, repaired with new parts and reassembled. All at no cost of course, under warranty. Drove it for two years after that and now at 74k miles. Haven’t had to do anything to it at all aside from oil changes every 5k miles on the dot at the dealer. Very reliable. Oh and btw I am a BMW/Land Rover tech 😅🤣 This engine is GREAT.

@CarlosFlores-wx9qm 4 ай бұрын

Thank you for the in depth explanation. Have had an M274 in a 16 model sport package, purchased with 34k on odometer currently at 78k stress free miles (knock on wood). So far only had the auxiliary battery changed under warranty, serviced the transmission at dealer at 55k miles, plugs at 48k, all other normal A and B services.

@frankoqhairul3485 7 күн бұрын

Great video, thank you

@johnfox2544 3 жыл бұрын

Yes more on this topic.

@1g2002541 8 ай бұрын

very informative! Great Video

@CorporateJetpilot Ай бұрын

I’ve been religiously running chevron 91 only since i purchased my 2018 E300 4matic at the dealer almost two years ago at 68,000 miles one owner. Now it’s at 110,000 miles and every 5K oil change it’s still running exactly the same way I had bought it. Smooth and quick. Just changed the PCV and thermostat as preventive and done the transmission at 100K and differential front and back. Oil changes makes a difference and so does gas. At 100,000 miles spark plugs changed spotless. Theplugs were not bad at all. Checked top of piston and it was clean

@Boymentation1994 3 жыл бұрын

Nice work! Great production on these videos

@fcpeuro 3 жыл бұрын

Much appreciated!

@jermainesmith4232 2 жыл бұрын

I love your work skills bro

@user-sg9xm6wr2d 3 жыл бұрын

First comment, I love you to follow you ksa🇸🇦

@KMBence 5 ай бұрын

I have an SRS system failure due to the Pre-Safe failure in the drivers seat belt tensioning. I thought my eco drive wasn’t working bc of that but there’s also an engine light and so the thermostat may also be the problem. Thank you for this video. I will be servicing my car soon at the MB dealer, hopefully they won’t charge me an arm and a leg for the servicing of the supplement Restraint System

@lookItsJayden Жыл бұрын

My sprinter van has one of these motors, I haul 1500lbs all day every day and it pulls along just fine.

@the_first_resort940 28 күн бұрын

Got 3 sprinter vans this week with cylinder 1 misfires and cracked pistons

@skakhtar560 2 жыл бұрын

Very nice to bro 😌

@Tony-hx2fj Жыл бұрын

Loved your video. Great job. I have a 2011 ml350 which I love but want the newer lane changing , parking assist. etc and considering a GLE 350 . I only drive 3-4 K miles/yr. Should I get an excellent condition 2016 GLE 350 V6 or 2017 GLE 350. Towing and gas mileage don't matter. Thank you for your time and Consideration, Tony

@chrispowell3227 4 ай бұрын

Video on installing upgraded turbo reinforced pistons and intercooler please!

@23omorales 10 ай бұрын

I would love to see a guide on replacing the crank position sensor on a 4matic model. There’s nothing online and I’m having a bit of trouble figuring it out.

@ralph332 2 жыл бұрын

Could you do a series about the m264 engine?

@trubeats864 2 жыл бұрын

Can you please make a video on replacing the simple crank case valve

@Uniquetransition 3 жыл бұрын

Can you do a buyers review, parts, problems, etc. on the W213? :)

@listferenc2323 2 жыл бұрын

Hello. I like to ask you, where you can see the motor temperature gadge on the 2015 w205 350e hybrid? Thank you.

@philipzigli9740 2 жыл бұрын

Keep the great work going bro. Can you make a video of how to change PCV valve on 2015 C300

@fcpeuro 2 жыл бұрын

It is on our list!

@lou007 3 жыл бұрын

what about a disassembly? 😎 great job guys.........

@derekinhawaii 2 жыл бұрын

Sadly I'm currently into the Oil separator value assembly replacemen that you mentioned in the video... What a pain in my ass....here's what I've has to remove besides a bunch of the sensors... Intercooler, ECM and bracket, starter, engine mount + bracket, a thick rubber shield. I'm 5hrs into it and I've only at the point of being able to see one of the 3 bolts on the lower part of the assembly that connects to the lower part of the engine... I'll say it will take me 8-9hrs to finish this job. Mercedes Benz dealership wanted $1600 for parts and labor. If I were to do it again. I'd give them the money. This job is certainly one of the worst and pain in my ass fixes I've done in a long time. This should be a recall item AND/OR should be covered as part of the extended emissions warranty that comes with the car. TOTAL BS...

@chosenone8875 3 ай бұрын

Hi Kyle. I.find your Mercedes Benz vids clear and informative...i just had the 2 front airmatic suspensions changed in my 2016 Merc C200 amg package by a mechanic..but i noticed on my way home a Malfunction light on the dash and my car is a bit higher on the left side(Car is RHD)..Can you say what could be the cause?. Am frustrated..thx..awaiting your response(i am a female)..God bless you

@shaunmiller3342 6 ай бұрын

What do you think of the 2020 Mercedes GLC300? Is it reliable and can go the distance? I just purchased one and want to know what to look out for

@chriskros8858 2 жыл бұрын

W205 is my first car without low oil pressure red indicator. How can I to check if the pressure is OK and what if not OK? Is there any information on dashboard?

@sukhwang4554 Жыл бұрын

This channel is right on. Very precise. Yes Turbo is bullet proof, but diaphragm goes bad. Yes PCV is big problem which cost 1-1.5K$ to customers. GLA is little different tho, GLA is much worse design it will cost you fortune. Otherwise nice smooth 2.0T engine with least problems and good power.

@RexNathanChan 6 ай бұрын

mmmmthese iridium spark plugs are good for 100-150k kms, hes being over cautious with such short intervals.

@jimyale469 2 жыл бұрын

Nice video, I would definitely like to see more on the M274 engine. My 2016 Metris is throwing the code for the PCV system and I would love to see a video on replacing that.

@fcpeuro 2 жыл бұрын

Sounds good, Jim!

@gwindy6439 2 жыл бұрын

Bro thats pain to replace it, it takes 6-8 hours to replace that pcv system. And its gonna cost arround 1500 to 2000$.

@Baruchashem32 4 ай бұрын

Mercedes extended the warranty on the part to 150,000 Miles P052E should be the code

@ang5738 Жыл бұрын

Could you please do a guide on M264 and which years to avoid?

@dimmacommunication Жыл бұрын

In my family m270 engine the oil is getting diluted with gas, is this a common problem to 274 too ?

@okolieemeka5552 Жыл бұрын

Can I get the pin out description for the ignition coil on this m274?

@RKingsEng 11 ай бұрын

Are the camshaft phaser plate adjustable?

@rashidafandiyev 2 жыл бұрын

I have also W205 2015 . I want to know how can i change fuel filter? Because our country fuels is not clean

@LynxStarAuto 2 жыл бұрын

Those water pumps fail all the time too. They seize and take the belt and anything in the belt's way with it. Also, some versions use a dual stage pump that routinely fails as well. Causes the engine to run hot at speed. Routinely misdiagnosed. And unless I missed something, the turbo had to come out, as the pump lives under the turbo. That means you'll be doing all the seals and gaskets on the turbo as well. Egregious water pump design for sure.

@wr2630 3 жыл бұрын

Very useful video thanks for it and more of it is absolutely welcome ;) It is a little bit more noisy than a normal gasoline engine, I asked MB dealership they said thats because this engine has a very high feul pressure about 200bar which make that extra more noise by idling

@JeeperZJ 2 жыл бұрын

The injectors, by their nature, are also louder since they're the piezo design which is basically vibrating crystals that create a current to open the injector nozzle when commanded.

@JrBetancourtcom 2 жыл бұрын

That’s what many people were told but if you listen to this video at 5:50 he talks about the piston slap… that’s the noise I heard when my car was sounding like a mini diesel . It wasn’t because of the high fuel pressure or anything else , it was the sound of the piston slapping the inside of the cylinder wall which would later lead to it cracking as mine did at only 51k miles. The newer models are a lot quieter btw - they fixed the wrist pin issue

@edwardhung6432 2 жыл бұрын

Does anyone know where the throttle body is? Many thx!

@garylim6486 2 жыл бұрын

how serious with P219C, P0301and misfire...had replaced spark plugs, ignition coil , air filter, fuel injector in cylinder #1....but engine still shakes and chk engine light came back on

@mericok5569 3 ай бұрын

What is the socket size of oil filter remove?

@shadisaadi1173 3 ай бұрын

Which engine is have more reliability rating . Mercedes m274 or bmw b48.

@farairangai2893 2 жыл бұрын

I have an issue with my m274 on w212 it has a hard start issue and a fault code p0016

@philipinem5503 Жыл бұрын

What do I do if my crankshaft position sensor is faulty

@shamalanon-time4209 2 жыл бұрын

Thank you for the video. Our 2014 Japan spec 1.6 M 274 has developed a noticeable ticking sound. The sound came up immediately after starting the engine one morning and has since not gone away. Sent her in to Merc specialist here in Malaysia who after a day of servicing (e.o. Change) and checking says it is the CGI pump and a very normal sound. Having driven this car for 3" years, decided to start and listen closely. On idle, you There is duration that comes and goes where the ticking sound gets faster after what sounds like a snap over, then back to the slower ticking sound within a brief period of about 30-40 seconds. From the bit I have read, it sounds more like cam chain or cam lobe or cam gear there about. Any guesses would be greatly appreciated. TIA

@shamalanon-time4209 2 жыл бұрын

Forgot to mention it has approximately 45 K Kms on / 26k miles and there were 2 incidents of strong fuel smell for few seconds upon starting in the weeks before but not after. Mechanic checked hoses to and from the CGI with no leaks or cracks detected.

@str8ballin297 2 жыл бұрын

@@shamalanon-time4209 it is a broken piston

@muhammedmekec4663 8 ай бұрын

1.6 lt motormu var

@vozhoga 6 ай бұрын

have same sound every cold start. I think its normal, just when engine heats up injectors works lil bit different, trying to heatup as quickly as poss..

@cristianisnardi6066 10 ай бұрын

Very interesting your video and very useful! Honestly, I was very intrigued when you talked about the common issue that this engine has with the piston. You described some exact sounds that my M274 makes in the mornings when the engine is cold. I have a 2018 C300. You mentioned that this is common in the 2015 and 2016 models. I hope that this is already resolved for the 2018 model. However, your description of the issue matches what's happening with my engine, but only when it's cold. After about 15 minutes, it works perfectly. The car has 36,000 miles and is very well maintained. Should I be worried?

@fcpeuro 10 ай бұрын

Hey there Cristian! Your C300 should have an M264 engine, which is a bit different from the M274 that Kyle is diving into in this video. While Mercedes has acknowledged some valve seat issues on the M260 and M264 twins with an extended recall (fairly unlikely given your description, but may be worth looking into), they haven't noted any of the wristpin issues present on the early M270 and M274 engines carrying over to the newer family. The clattering of the direct-injection fuel delivery system on your engine is generally pretty noisy when functioning tip-top, which could be a part of what you're hearing. This being said, if you're hearing a noise that concerns you, swing by a dealer or independent shop to be sure it isn't a cause for concern!

@cristianisnardi6066 10 ай бұрын

@@fcpeuro Thanks for the response. Unfortunately, the M274 is in the c-class, W205 from the 2015 to 2018 models. The M264 engine is from 2019 onwards in the c-class. When you mentioned that my engine was different, you made me doubt and I investigated. Besides, it's the same engine as in the video, as far as it looks. I'm very worried because I have the exact symptoms. I live in NYC. When I took the car to Mercedes Benz for maintenance, they said everything was fine. But no, I'm sure that this engine has the exact symptoms described in this video. Only when it's cold. So I started researching more deeply and found out that several owners of this engine had problems with the piston at any mileage - 16,000, 30,000, 100,000 miles. It breaks out of nowhere without warning. I also found out that there's an ongoing lawsuit in California for this issue. I also want to think that it might be false information. But when I saw this video, my doubts are present again. Honestly, I don't know what to do. I take very good care of the car and always use the remote start before using the car to warm up the engine. Thank you for your time.

@Y-Kay 9 ай бұрын

Can you keep us updated on your journey with this issue? Thank you for your time 🙏

@cristianisnardi6066 9 ай бұрын

The car continues to run perfectly, only the noise in the mornings described in this video. At 4 minutes when it's fully warmed up, it stops. It's the same description, like metals rubbing together and a slight knocking. I maintain it very well. I have all the maintenance documented, the car has only 36k miles. Everything has been changed, including the coolant and brake fluids. Everything is very well controlled. So far, the car runs like a dream. But I'm always worried about that noise. I'm already considering selling it.

@ninevahkeith 2 жыл бұрын

Hi I have a 2017 infiniti q50 2.0t and on mine the ecu is on the very top of the engine, not like the one in the vid, are there any significant differences between the ones nissan gets, and the ones mercedes uses? If so what are they

@arturpytel9940 Жыл бұрын

Hi, what about reliability of your M274 on that Q50S? I was thinking about such car but after deep diving into M274 tech issues, I gave up on it. Too risky in my opinion, compared to Nissan's engines mounted on Q50 series.

@johnpier3026 22 күн бұрын

2017 E300 suffered #1 piston failure at about 110K miles, always well maintained and fed on Costco premium fuel. No help from Mercedes corporate. Had block replaced by my local mechanic. Still waiting to see if a class action suit comes forth. MB should have a recall on this engine. Also as everyone else, I have had numerous problems, but I was lucky enough to have them serviced through an extended warranty that I had purchased thru MB. Latest is a P0299 code...MB recommends replacing the entire turbo assembly...turns out the waste-gate vacuum actuator was bad, found one on Amazon, fixed problem. $40 dollars vs $4000.

@fcpeuro 15 күн бұрын

Sorry to hear this has happened to you :(

@james__wilson Жыл бұрын

My 2016 Metris has the "Low Boost" code and surges boost before going to full limp/zero boost mode. No matter whether it's 3psi, 11psi, or 18psi it will not allow for more than one second of boost before opening the wastegate. No boost leaks, smoke test is clear. Replaced turbo, intake manifold, boost solenoid, boost sensors, intake temp sensor, water pump. Showing P0420 also for cat but it has two new OEM O2 sensors. Magnaflow cat has been on order for months, wondering if for some reason it is limiting boost for that? Cat visually inspected when turbo was replaced, but only from the front site. A few other Metris guys are having this very same issue so I'm the lead dummy spending $ with the parts cannon to see what sticks to the wall. Mercedes/Sprinter dealers won't work on them anymore in my area, so we are out of luck. We order all of our parts for our Metris, BMWs, Minis, and VW's from FCP Euro to keep this family fleet running!

@james__wilson Жыл бұрын

161K miles on it, it's a work van that we'd like to retire to a road trip/van life rig. Bilsteins, Sumo Springs, and some other upfitted items so we are not a Dump-and-Run type...we want it to work and live! Sending off used oil analysis to Blackstone Labs from this last oil change.

@vaskoma4o Жыл бұрын

I've read that also a lot of people (also me) have gasoline smell, which happens to be from the hoses before and after the high-pressure fuel pump. this happens only in the cold, when hoses are hard, when its warm, they get softer and they do not smell. this is no joke, this issue is not addressed by mercedes, its left to do it yourself

@ninevahkeith Жыл бұрын

I'm not sure what version of this engine is in my q50 bit I'm hoping I lucked out, I use mobile 10w40 and change every 5k and spark plugs every 40k miles I drive that car very hard and I'm at 83k with no issues whatsoever

@sourabhsangale3952 3 жыл бұрын

Please post a video on s class .

@fcpeuro 3 жыл бұрын

we'll definitely add it to the list!

@corynrobinson 2 жыл бұрын

I’ve had the PCB code a couple of times. Apparently MB is working on a new design. It would be nice to see a video on replacing that system.

@JeeperZJ 2 жыл бұрын

It's a relatively complex repair. Intercooler has to be moved, lf motor mount has to come out, you're gonna want a few more specialized tools. It can easily eat up a good portion of your day if you really don't know what you're doing....not recommended for someone who isn't familiar with the engine.

@derekinhawaii 2 жыл бұрын

@@JeeperZJ Agreed. I'm currently on 5hrs and I'm just able to see 1 off the 3 bolts to the assembly on the lower portion go the motor. This job in no joke. WHAT A PAIN IN MY ARSE!.. Personally just for the headaches, I would recommend to give Merc Benz the 1400-1500 they want to do this repair. In my opinion it's not worth your time. But I digress...

@assibeyenoch5385 2 жыл бұрын

Am having this noise in my car 274 and I don't know if is bring

@alicitak1352 24 күн бұрын

Greetings, I have a W212 e180 1.6 2015 274 engine vehicle, the tachometer is constant at idle, but there is shaking when you give gas at constant speed, the authorized service changed the spark plug, the problem continues, there is no fault code other than thermostat failure, authorized service, injector, tank fuel. pump, high pressure pump, it says let's change the coil, but this change requires a lot of money, first of all, where do you think I should look for this shaking failure, shaking does not always happen, it does it for 10 minutes in 1 hour of use, in total, the tachometer is hovering between 1500 and 2500 rpm, sports You don't feel much shaking during use, regards.

@1paulwang1 2 жыл бұрын

I have the extended geico warranty 7 yr/100k mile for mechanical breakdown. Ill see whether i keep 2017 infiniti q50 2.0 which has the m274 engine. So far 72k miles and not one issue

@arturpytel9940 Жыл бұрын

Hi, you posted it 6 months ago, what about reliability of your M274 on that Q50S? I was thinking about such car but after deep diving into M274 tech issues, I gave up on it. Too risky in my opinion, compared to Nissan's engines mounted on Q50 series.

@ShowMeWhatINeedToKnow Ай бұрын

No mention of the cracked pistons?

@petadamon 2 жыл бұрын

Yea please post the diy for the PCV. I've got a P052E code currently :(

@Baruchashem32 4 ай бұрын

Mercedes extended warranty on it up to 150,000 p052e

@Kenny23384 Жыл бұрын

anyone know if a tune can kill the reliability on these engines? I have a 2017 e300 and would love more power but have always kept my cars stock since i didn't want to play with the reliability

@DaPopeOfDope101 Жыл бұрын

I know that AMR makes various tunes for it, they’re pretty expensive unfortunately, $1,300-$1,500 for a C300, but I hear they can give 50-70bhp depending on what kind of bolt on’s you’re working with. Hope this helps!

@depeapa22 Жыл бұрын

Por favor le puedes poner al video traducción al Español ? O subtitulado al español

@exoprasta 2 жыл бұрын

Mine’s got clanking sound on cold start and sometimes triggers the fan to start, but after coming to temp it seems to disappear…any idea why?

@gazathug876 2 жыл бұрын

Probably was using the wrong fuel

@rajvindermudhar1011 2 жыл бұрын

Can the water pump start making noise? My c300 makes this noise as the RPMs change, sounds like valve tapping. Please advise

@fcpeuro 2 жыл бұрын

Water pumps can definitely make noise as they start to go bad. Valve tapping noise can be anything, unfortunately. You can have noisy lifters, a bad bearing on an accessory or pulley, low oil ect.

@cupompa 3 жыл бұрын

I owned the 2017 C205 with the M274 engine for 3 years. Put 27,000 miles on it. I would love to see you guys do a DIY on replacing the rubber fuel hose near the steering shaft that causes the A/C to smell like gas/fuel. Also diagnosing for a brake squeal fix on cold rainy mornings! From experience of course 😁

@cupompa 2 жыл бұрын

@Michael Lee Oh it did not need new fuel lines. I read on the W205 forums that the solution to the fuel smell from the A/C is just a tighter clamp on the rubber fuel line near the steering shaft. You can see my ownership thread here. Not bad reliability at all. I sold it after 4 years because my boss gave me her husband's BMW for free! And I didn't need 2 cars during the pandemic: mbworld.org/forums/c-class-coupe-c205/768895-el-nino-ownership-thread.html www.e90post.com/forums/showthread.php?p=27506300#post27506300 As for long term reliability after 5 years, check this video out also on the M274 motor! (Since you clicked on this maintenance video). Magic Mike was a Mercedes-Benz dealership tech for 6 years~ and actually responded to my question on his thoughts of this engine. He replied and told me, "I personally wouldn't buy a vehicle with the 270 or 274 engine, but I know there's folks out there that have had good results. ": kzfaq.info/get/bejne/pr6og8uq3czdkqM.html

@andreializeu93 2 жыл бұрын

@@cupompa I have the same problem with the gas smell. It might be the rubber fuel hose. Was it a hard fix? I currently own a w204 1.6 petrol engine for Europe. M274 engine.

@DroneBluez 2 жыл бұрын

@@andreializeu93 mbworld.org/forums/c-class-w205/737303-dealer-says-fuel-smell-leak-w205-2015-c300-base.html

@bmwlane8834 2 жыл бұрын

George, check with the dealer....there was a recall on this engine to replace a defective fuel line. Should be no cost to you.

@JeeperZJ 2 жыл бұрын

It's an easy fix, we replace the soft hose and the clamps. Remove the cover that sits over the hpfp to gain access up top, access is easy with the transmission underpanel removed when below. My advice is to attach a shoestring to the old clamp up top and tie it to the top of the engine and remove the hose from below pulling downward. When you install the new hose go in the reverse and you'll have a much easier time with the routing of the hose.

@HappyFeet-cc1jc 2 жыл бұрын

I own a 2015 E200 coupe with M274 engine right now and it's show code out of nowhere P217800(Mixture failure, rich fuel in bank 1), which part should I be concern or where should I check first? does it urgent to fix?

@amilcar5772 2 жыл бұрын

How many km?

@twoc400s5 2 жыл бұрын

Saying that Piston issues were only present on very early cars/engines is absolutely incorrect. There are dozens of cases with USDM and ADM models of this motor from 2017 onward with catastrophic piston failure in Piston 1 and some with multiple pistons. Failure mode ranges from cracked ring lands to completely cracked piston crowns. I can't believe MB USA hasn't been forced to recall these motors or had a class action law suit brought against them as they often fail JUST outside the factory warranty period. I know some owners in CA have gotten MBUSA to pay for replacement because CA makes pistons covered under the 80k mile smog equipment warranty.

@JrBetancourtcom Жыл бұрын

Hi, I sent a petition to the administrator of the NHTSA to investigate this piston issue as I was affected and after months and months of pushing the issue they were finally kind enough to start an investigation . If you look at the open investigations for 2015 c300s there are now three and the wrist pin / cracked piston engine failure is one of them . This started about two weeks ago, so let’s have faith in our government to make Mercedes do what is right and take responsibility for this problem. It is totally unsafe for someone to be driving on the road and have this unexpectedly happen, it’s only a matter of time before someone gets hurt and the NHTSA has the power to force Mercedes into recalling this engine .

@ezekilla123 2 жыл бұрын

My check engine came on. Read the code it was a cylinder 2 misfire. Replaced the spark plugs and changed the ignition coil. But after 500 miles of driving another misfire occurred in cylinder 2. Any help or suggestion what can be causing this ?

@tylerboulware902 2 жыл бұрын

i work at a mercedes dealership and we have been replacing cylinder heads due to this problem

@onefabricio 3 жыл бұрын

Can you do a video like this on the M276

@fcpeuro 3 жыл бұрын

we'll have the team add it to the list!

@Ben-wq4zf 2 жыл бұрын

What is the reservoir behind the air filter and what is it for?????

@madmike9696 2 жыл бұрын

intercooler circut

@Remzijarrah 2 жыл бұрын

is there a power steering reservoir on this engine? if so where can I locate it?

@ayoogbeide6637 2 жыл бұрын

It’s uses electronic steering

@moauedemar4243 2 жыл бұрын

Hello, I have a problem with the engine. A suspicious sign appears in the car, and the car’s torque is weak. Oil rises on the surface of the engine

@spoon16clubsport73 2 жыл бұрын

Thank you really nice video 👍. Mine just got fuel leak at low side pipe of high pressure pump got it fix yesterday. Not sure state model has this problem in mine country has this issue a lots.

@fcpeuro 2 жыл бұрын

This seems to be a common theme. We just filmed a quick tech tip mentioning that on the M274 engine!

@kfirlogasi6651 Жыл бұрын

Is the M274 engine reliable? im looking to buy SLC 1.6T with 156HP. need your help!

@RexNathanChan 6 ай бұрын

Yes, if driven often. My mechanic has had to replace thermostat (3 way valve $400AUD OE MB part) on cars driven short trips.

@ansonchan6835 2 жыл бұрын

Has anyone replaced their POLY-V Belt yet? There isn't a designated interval but looking to see what is common practice as I wouldn't want it to snap before replacement.

@RexNathanChan 6 ай бұрын

I think visual check is ok, I think I did mine at 150k kms? Got to 290k kms (2014 A180) before car was written off by rear end crash

@lupsabogdan4158 Жыл бұрын

I have a c200 w205 petrol ... the check engine came on, I took the car to Mercedes and they changed my NoX sensor.. after 3 months the check engine appeared again .. the same problem again, the NoX sensor was changed ... after 3 weeks the same problem check engine with NoX sensor error ... what could be the problem?

@RexNathanChan 6 ай бұрын

There's a NOx sensor? you mean oxygen O2 sensor or knock sensor??

@maticsorn2784 2 жыл бұрын

Is there any cases on excessive oil consumption c300 only 30k milles?

@twoc400s5 2 жыл бұрын

Yes, usually related to oil control ring failure on piston 1.

@lotanmineslm Жыл бұрын

Hello, I am interested in purchasing such an engine, exactly perfect and new, fully equipped, how can you help me purchase such an engine for my vehicle, I am the owner of a Mercedes Benz C-Class C 300 2.0 turbo M274 engine 245 horsepower

@aiden5538 Жыл бұрын

I have an m274 with the start stop not working but its not throwing any codes and temperature seems fine

@RexNathanChan 6 ай бұрын

Usually Aux battery is dead.

@shenalsmith8555 3 жыл бұрын

Can u do a engine tuning in this car

@fcpeuro 3 жыл бұрын

in general, its likely possible, but we here at FCP Euro do not

@yuusifmusahamadu5540 2 жыл бұрын

Please is this engine 2.0 L4? How many oxygen sensors this engine have?

@fcpeuro 2 жыл бұрын

Hi Yuusif, you will have one upstream and one downstream for this model.

@moesawat7974 2 жыл бұрын

What do you think cause the fuel smell inside the car?

@fcpeuro 2 жыл бұрын

Hi Moe, sometimes the fuel like coming off the HPFP cracks, and causes a small leak. We have this kit in place for that. Mercedes Fuel Hose Kit - Genuine Mercedes 2740703500

@cebompiko8923 Жыл бұрын

On my M274 it has a tendency of cutting power under heavy acceleration. What could be cause?

@fcpeuro Жыл бұрын

Hi Cebo! A good first step would be scanning the ECU for any stored or existing code. This could indicate if you're experiencing a misfire condition or something a bit more involved.

@user-lo5ib4kt9r 2 ай бұрын

I had the same problem, changed the spark plugs and crankshaft position sensor and this fixed the issue.

@teopeiling1912 11 ай бұрын

Would you know where the Camsahft position sensor is for this M274 Engine? As we are seeing the engine light sign and would like to fix it by replacing the sensor

@SorinMiron 3 жыл бұрын

"terrible but not too terrible m274 engine" - can you add more details to why you believe this to be a terrible engine?

@MD-vf7rs 2 жыл бұрын

my experience, sounds like a diesel engine, two different mercedes enthusiasts one of them is a car repair shop owner and a mechanic told me it’s not reliable for pushy drivers, he also sent me vid of very damaged piston of an engine driven 29,000 kms only!

@LynxStarAuto 2 жыл бұрын

I work on these cars for a living. 20+ years now. The M274, like the M270 (transverse mounted) 4 cylinders are basically boat anchor motors developed in conjunction with Renault. These clunkers get all types of issues. One of the worst water pump designs ever (lives under the turbocharger)! Also the breather system is complete junk. Has a breather hose which breaks a lot, that requires intake manifold removal just to replace. Pays about 5 hours of labor to replace. The coolant tanks are always leaking, horrendous ignition coil/boot design. Rarely do the coil boots survive disassembly. And the fuel injectors are known to fail as well. They are pricey, and require unnecessary special tools to replace the seals in the fuel rail. All of that for an engine that doesn't make that much power, and isn't exactly winning any fuel economy awards either. V6/V8 or bust when it comes to MB.

@JrBetancourtcom 2 жыл бұрын

My piston cracked at 51k miles . Diesel sound is piston slapping against cylinder wall

@ronjohnson8119 Жыл бұрын

@@LynxStarAuto same.

@thomasy3464 Жыл бұрын

Please share the part number for the PCV valve

@VanquishMediaDE 2 жыл бұрын

In April of last year (2021) I was driving my 2017 C300 (W205), piston 1 cylinder 1 had failure (ejected through the engine block) with 86737 KM (53,896 M) on the odometer, I was about 3,896 miles over my factory warranty. Due to my engine block being damaged (the piston went through the block and ejected onto the highway) the repair cost was going to be 12,000EURO. Mercedes Corporate refused to offer any support (good will warranty or otherwise). Mercedes has terrible customer service, I had every oil & oil filter change (at 5,000 mile intervals) performed at the dealership. My car had excellent MB dealership service records and MB still refused to help me. I did not owe anything on the car (thank God I paid it off) so I had to scrap it for pennies on the dollar of what I paid for it. I will NEVER drive a MB again. I have since replaced the car with a BMW 330i and I have been very blessed to not have any issues with it. For me it is not about the money, it is about the principle, one does not buy or lease a Mercedes Benz only to have the engine blow up with only 87,737KM on the odometer! And for the repair cost of the total engine replacement I could have just bought a new car with that (which I did). Please do not buy a C300 (W205) or any MB with the M274 engine.

@fcpeuro 2 жыл бұрын

So sorry to hear that!

@VanquishMediaDE 2 жыл бұрын

@@fcpeuro It sucks but I made the best out of a terrible situation, now I have a very well maintained BMW 3 series (330i) and it has been very reliable and dependable. I always get more oil change kits and parts from you guys at FCP Euro :)

@juchou2983 Жыл бұрын

You jumped from one hot frypan to another hot frypan. BMW/Mercedes and Audi builds very poor quality cars (but fun to drive and good looking) and does not care at all about customers. You would be much better of with a Lexus/Acura or Infiniti ... Less fun but you will not need a new engine every 3-4 years.. Also Lexus dealers have excellent service. I got a free dashboard on my GX as a good will replacement 10 years after the warranty was expired...

@soILLitsADVISED Жыл бұрын

@@juchou2983it’s not a valid argument to write off an entire brand. You sound like an unreasonable un-researched alarmist. Just as there are black sheep engines within a brand, as there are ol’reliables. I have an ‘06 BMW 325xi w/an NA (naturally aspirated) N52 engine that I bought in 2012 with 73,XXX miles. I still have it today with 240,XXX miles. My maintenance wasn’t the stuff of legends either. Hasn’t cost me a fortune. Has been in the shop a few times over the years. Cars are all complex puzzles. Even the simple ones. Something is bound to break.

@juchou2983 Жыл бұрын

@@soILLitsADVISED it is an well established fact that post 90s BMW-mercedes-audi are very unreliable and high maintenance cars. You sound like one of those fanboys who bought something and starts claiming how great it is.. BMWs almost always have gasket issues, water pump failures, hard to diagnose random misfire issues, oil burning and so many other major problems. BMWs need reprogramming after just a battery change!! Your anecdotal evidence does not really mean anything.. How many BMW can you show that has more than 200k and still runs properly? I don't understand this blind loyalty that people have for some brands. Yes they are fun.. I have owned a couple of them.. But it's just silly to claim they are reliable. What do you think is the reason you can buy a 2010-12 7-series for 10-15 grand?

@emmanuellukhanda3556 2 жыл бұрын

I have the fault code PO304

@averagedev7768 2 жыл бұрын

Well in USA you might see V8s, here where i live tax is high for big displacemnet engines so you are very rich if you drive a V6 diesel. This engine is 1991cc and that is very improtnat if you have this kind of tax. This engine with LPG migh be the best go to before all the cab drivers grab these cars. For example here you cant find a good M271 engine anymore from the overuse as taxis or kids who think they are cool in there W203 manual with a straight pipe

@jupapri 3 жыл бұрын

M276 engine please

@fcpeuro 3 жыл бұрын

we'll add it to the list!

@ericn7698 3 жыл бұрын

@@fcpeuro Didn't you already make a video on the M276 titled "W212 Engine Diagnostic & Maintenance Guide?"

@aasastephenson1538 3 жыл бұрын

Ecu tuning options?

@brandinconroy3489 Жыл бұрын

these things are still eating pistons, we "at my shop" have seen 3 in the last year... newer ones too, just saw a 2017 or 2018 only 39k on the clock, it's sad but they're just trying to get too much out of these engines and making them as cheaply as possible... actually there is a class action lawsuit going on currently over this engine specially, good luck and don't buy one of these cars that come with a M274, Mercedes is usually very good with engine development, this one must have been on a Friday at 4:30pm...

@skakhtar560 2 жыл бұрын

👍

@jamaicaz89 3 жыл бұрын

So pcv can only be fixed by replacing

@derekinhawaii 2 жыл бұрын

yes. it doesn't come separate from the assembly... trust me... this job is horrible and a pain in the ass. 5-8hrs from start to finish depending on you experience. possibly even longer. pay the dealer. it might be the one time it's worth it.

@andreializeu93 2 жыл бұрын

Drive belt? This thing doesn’t have a chain ? I’m confused sorry.

@JeeperZJ 2 жыл бұрын

The belt runs the engine accessories

@ronjohnson8119 Жыл бұрын

A drive belt runs the accessories (alternator, a/c compressor, water pump, etc) whereas a timing belt (or chain which this engine uses) is what connects the crankshaft to the camshaft (s).

@muhammedmekec4663 8 ай бұрын

videodaki araç kaç motor .lt ..hb

@fcpeuro 7 ай бұрын

Hi Muhammed, this is an M274 focused video!

@gary8853 3 жыл бұрын

I’m dreading the day when my ‘19 Metris van’s PCV fails. Driver’s side ECU and engine mount need to be removed to access the PCV assembly. Ppl who had it say it’s about a $3k job at the dealer 😐

@derekinhawaii 2 жыл бұрын

My dealer wanted $1400 to do it on my 2017 E300. I elected to do it myself... NEVER AGAIN... After 5hrs and I'm about 60% from done. Next time I'll pay the $1600. Not worth 8-9hrs of my time...

@jameswan670 3 жыл бұрын

One major defect is poor quality of cam shaft.

@arturpytel9940 Жыл бұрын

Yup, you can read about it here, there are pictures as well: ezoteriker.ru/en/opisanie-dvigatelya-m-274-de-20-al-opisanie-dvigatelya-m274/

@eevelyn19 3 жыл бұрын

He acts like Mercedes has never made a 4 cylinder before

@gilsonrogeriolimaoliveira2807 3 жыл бұрын

In the USA they weren't available until not long ago. We in the poorer parts of the world are used to it, though. And this version of the M274 is the strongest one, here in Brazil the most common is an 1.6 liter with 156cv.

@mzee5533 3 жыл бұрын

@@gilsonrogeriolimaoliveira2807 Americans love big engines V6, 8, 10 or 12

@gilsonrogeriolimaoliveira2807 3 жыл бұрын

@@mzee5533 everyone loves a big engine, but nowhere in the world gas is so cheap as in the USA.

@twoc400s5 2 жыл бұрын

@@gilsonrogeriolimaoliveira2807 the Mercedes 16v Cosworth motor is both well loved and highly desired. It was introduced in 1986 to the US market.

@povilasmarveloustv3810 3 жыл бұрын

the engine itself might be small as it's a 4 cylinder, but that engine bay looks absolutely cluttered with shit. Great video as always though.

@badkid73 2 жыл бұрын

Cluttered is relative, and that engine bay looks so much easier to work on than a modern BMW

@lukewessels2242 2 жыл бұрын

Doesn't the W204 use the M271... really curious about the differences in the engines

@kudzitsuro6448 2 жыл бұрын

It also uses the M274 1,6 engine only last ones made jus before w205

@ronjohnson8119 Жыл бұрын

271 is a decent engine, the 274 is a complete steaming pile.

@next24 8 ай бұрын

@@kudzitsuro6448 Does the 1.6 m274 in w204 have problems with pistons?

@bradwilliams1213 23 күн бұрын

I have a 2019 E300. Garbage! 57k miles, and the intake adjuster broke. A $7,300 repair. The service advisor said it's a Nissan motor. He said it's not worth keeping but with a trade-in value of $20k that's negative $11.5k from what i owe. That's why you never buy a Mercedes.

@Coolmanvideo Жыл бұрын

So sensitive and so much issue with this engine and its only producing 211HP . That is 0-100 in 7.2 secs . Not superfast at all. Really not worth it buying a merc with this engine. It needs too much care and maintenance while not giving a very good performance.

@RexNathanChan 6 ай бұрын

I did 290k kms in 8yrs on this with just oil/filter chnages...

@ronjohnson8119 Жыл бұрын

Absolute piece of garbage engine. I am working on one right now and I just can’t believe how bad it is.

@jameswan670 2 жыл бұрын

Worst Mercedes engine ever - M274, M276

@wadesautoresto1450 2 жыл бұрын

Curious what makes you say that about the M276. Thanks.

@ronjohnson8119 Жыл бұрын

The 274 is a COMPLETE piece of garbage but overall the 276 hasn’t been too bad.

@jameswan670 Жыл бұрын

@@ronjohnson8119 Timing chain part is peice of real shit.

@RexNathanChan 6 ай бұрын

cylinder bore scoring? @@wadesautoresto1450

@invest7050 10 ай бұрын

what is this error P13C523

@fcpeuro 10 ай бұрын

Hello! Mercedes notes this code as referencing a "short-term torque limitation as detected by knock control." We'd also recommend checking if there are any codes relating specifically to the knock sensors that may indicate replacement is worthwhile.