Well thank you very much for watching the video my friend! That is so awesome ! simple easy fix!

Thank you for watching 😉👍

dlarremore thank you for watching the video 😊 I’m not sure if you have the same engine as my but I also change my spark plugs every 3 months because I use my boat a lot and man this thing is like a monster that eats spark plugs.. I have hurth transmission on my boat so they start making weird noises where the engine is not running so good so when I can hear my transmission I know it’s time for a tune up 😊 I hope it helps. Thank you again

Thank you for watching 😊

Thank you for watching 🙂

Thank you watching and stay safe! 🙂👍

Check your ignition system. Distributor cap and rotor, spark plugs, spark plug cables. You are probably running short a spark plug or two, from there on, fuel pressure and stuff but easy pease you have her straight in no time! Thank you for watching the video 🙃

Thank you for watching the video bud! Well you are going to right direction.. backfired can happen on a lean mixture to but more often than not the problem resides on the rich side, take your distributor cap off and and check how it looks down there it’s probably time for a new one and check your ignition timing because if it is even a little bit off can cause backfire and spark plugs and wires should be one of the next things to, The last thing on this list would be your fuel pump failing and at that point right there you have done a full service and you probably will have reached the problem, the next thing that would cause backfires will be bad valves and stuff but don’t think that should be a problem, it’s usually something simple

I did switch mine to a fresh water cooled system and I have to say I do sleep better at night LOL but mine is a half system so the engine is cooled by antifreeze but the full exhaust system still gets salt water. I was told that the half system cools a little better than the full close loop but I guess not enough where would actually matter.

Do you have bravos or straight shaft?

Yeah Fort Lauderdale 😊 thank you for watching the video 😀

Cole Diffin thank you for watching the video 😊 the belt only goes backwards on the tensioner quite easy to replace and the load of the belt should be good because I went to west marine and asked for the belts for my engine but again can’t trust anyone 100% 😂

I sometimes do lol ethanol free at marinas here the prices are ridiculous so I usually use normal gas till I find a cheaper marina 😕

Hello my friend thank you for watching the video! If you’re talking about that rubber cap on the front middle bottom of the carburetor , That would be used on a automotive setup, if I’m not wrong that connects to the vacuum port of the transmission or something but on the marine application you don’t use that port that’s why it’s capped! But on that port you can also check your vacuum for the engine, that is probably why you have a 5 inches hose capped on it where you have that spark plug is where you connect a vacuum gauge to check the vacuum on the engine, on the very end of the video I’m checking the vacuum pretty much with the same little bit of a hose like the last owner left on your boat, nothing to worry about but that needs to be capped well so your carb don’t lose vacuum, what carburetor do you have? The carburetor number should be on the bottom front on the carb, The two marine grade ones are the 1410 and 1409, some rebuilders plug that port for the marine application because we don’t use it but the the Delbrock carburetors are pretty much the same casting just different jets and stuff so if you buy a 1409 that has that bib nothing to worry about just cap it ;-)

Cruising the South THANKS SO MUCH, I really appreciate it and love all of your videos!

😊 Anytime my friend! just glad to help!

Hello my friend thank you for watching the video but the first set of butterflies is the automatic choke that opens and closes them so make sure that your choke is working properly. Of course they will only close back up when the engine is fully cold because the choke works as a heat element, when you turn the engine on, 12 V is introduced to the choke warming it up slowly and that triggers the opening effect and when you turn off the engine that will slowly close back up as the heat element cools down, but if your engine is fully cold and and the front butterflies are still open, you need to do a check on your choke assembly, make sure the wires are connected good and a little bit of WD-40 do wonders for these things, and that is assuming that your carburetor has a electric choke, but if not the same thing applies, the mechanical choke is also triggered by heat, I hope this helps. Let me know what you come up with.

@@Cruisingthesouth Tried your recommendation and issue seems to have worked. Can't thank you enough for your advice. Happy boating!!

@@clintperez905 outstanding my friend!! Awesome to hear that

Mike Noneya thank you for stopping by 😊

Thank you for watching 😊 the hard work is definitely worth it 😆

It's better to take advice from someone that's on their boat , showing you the exact same thing you'll be looking at that's already learned by trial and error ,, be safe bro

I try to pass the message that if you get the boat you can fix it lol just get the boat 😆 thank you for watching

Thank you for watching the video my friend and Yep it’s that piece on the very top of the carburetor

Thank you for watching the video my friend and Yep it’s that piece on the very top of the carburetor

😅 thank you for watching I appreciate it, my friend! I wish you all the best I hope you get everything sorted out ;-) once you are down there maybe Slap a new distributor cap too I had a friend of mine‘s boat that his flooding problem was related to his ignition system which wasn’t my case but that does it too. have a great day and good luck bud!

Hello my friend thank you for watching the video! here’s a link of a video of mine of how I choose my carburetor there is a little math included on the video that you can calculate how much CFM do you need it’s related with your cubic inch and your top RPM, I stepped down from a 750 as I was to run to rich on a 454 but I only cruise at 3200 RPMs so you need to consider that ;-) kzfaq.info/get/bejne/jpN2qNpp1cDFm6s.html

Rochester 2 Barrel

Hey German! Could be your fuel pump failing! If it has more then 100 hours on it put a new one and as you at it take a good look of your fuel lines on the vacuum side (before the pump) for any possible air leaks also good chance to do spark plugs and wires and distributor cap and rotor for good measure lol right there you good for the season on my opinion 🙂

Is this what was happening? kzfaq.info/get/bejne/ipeGasSZ3c65hWw.html

Megan Perry thank you for watching the video but no mods have been done like for starter it’s a 1406 eldelbrock carburetor on top of a mercruiser 454 so nothing is going south there and serpentine belts require serpentine setup and that’s not how mercruiser set it up on this engine on this year. go to west marine with my vin number and that’s the belt you will get. But thank you for you expertises

Megan Perry You had me questioning my parts guy really good LOL I had to look it up but yeah I stand not corrected, on the 1994 Mercruiser 7.4 L they did not use serpentine belts back then so I do have the correct belt. Just figured I would post this here in case anyone else goes through this situation to. But thank you for your input to me and I really appreciate it and I’ll most likely take your advice and upgrade my carburetors to the marine grade which I really don’t see the difference but I guess it must be one but like I said before I am not a experienced mechanic But I had boats my entire life and the point of the channel is that if I can do it anyone can do it and I’m out on the boat every weekend and because of my preventative work I never have problems out there. These Mercruiser’s engines take a lot of maintenance but if you do maintenance them they run so good for a very long time. Once again thank you my friend

@@Cruisingthesouth OK, so the edelbrock 1406 is not for marine use, it's a 600 cfm automotive only, the equivalent in marine is the 1409. On a big block I would go with a 1410, it's 750 cfm. Just looking out for the safety of you and your passengers. I think the seawater pump belt should also rout over the motor circulation pump pulley, they look to be in correct orientation, the idler pulley looks like it's from a serpentine setup. I would check with a mercury dealer and or the mercury parts web sit. Safe boating

Megan Perry Thank you for your input but without any Disrespect you must be looking at it wrong because I have the full service manual and the engine is set up to the T how it’s supposed to be.. The 1994 454 Mercruiser DID NOT have a serpentine belts. I get these engines serviced over and over again all following the service manuals this just must be a different engine that you were thinking of.. subscribe to the channel I’ll make a video of the way it’s set up and I’ll show it on the manual ;)

@@Cruisingthesouth megan is right about the carbs. The 1409 and 1410 are the only coast guard approved edelbrock carbs. They look similar to the automotive models but the marine carbs have several safety features built in, like often a return fuel line, sealed off vacume ports and corrosion resistant finish to name a few. Its certainly worth the investment. Automotive carbs can malfunction and flood, spilling fuel into your bilge and cause an explosion. Here is an brief article that really explains the differences well. www.cpperformance.com/t-carburetor_selection.aspx

Hey Bryce thank you for watching the video 👍 well my friend I do this as a hobby not as a job but I will be glad to give you my two cents 🙂 what is going on with your engine?

@@Cruisingthesouth I have twin full inboards. I just bought the boat with one engine working and the other one isn't connected ant all. And it's missing the carburetor fuel lines and the spark plugs aren't connected. I just need someone to tell me what parts I need to buy and then somebody to hook it up for me

Hit up ( Bills marine parts ) by state road 84! These guys can get you anything you want also they will provide you some help! Go there with tons of videos and pictures show him what you need he will put you on the right path

@@Cruisingthesouth thanks I'll check that place out. I'm in South Beach so it's close by.

Thank you for watching the video :-) I know right it must’ve been a old stock item or something because since I replaced it I have had no more problems

@@Cruisingthesouth you should keep extra belts or a adjustable belt that will fit any size

Thank you for watching the video 🙂 yep Brazilian lol Minas Gerais

@@Cruisingthesouth LOL o sotaque nao engana mas vc ja tem alguns momentos que soa que nem americano. Parabens pelo canal e tambem pelo conhecimento que vc tem. Aprendi bastante com os teus videos. Abracao de Brisbane ;-D

Obrigado a você por ver os vídeos meu amigo! Se você precisar de qualquer coisa diz aí tamo na área! Abração!