Cutting & bending tricks angle bar | angle iron to 90 degrees with round corner. Simple bending tricks with out using cutting disc and paper template. Click & Support: bit.ly/3usOgIw #angleirontricks #welding #manualbending
Пікірлер: 40
@brightspark1961 Жыл бұрын
Excellent precise work
@conradoluisalcantara92862 жыл бұрын
Welder/ Structural Fabricator👌👍Napanuod ko Sir,naka proper PPE ka at malinis maayos ang work mo.👍👌😷☺
@metalworksph2 жыл бұрын
Maraming salamat sir, god bless po sa inyo.
@jorisArt8 ай бұрын
Great video! Thanks
@johnambro7181 Жыл бұрын
Always learning, now a new technique for angle stock ninety bends- impressed, cheers.
@scottcates Жыл бұрын
That's impressive accuracy with the cutoff wheel. Decent welding too👍
@sumitjalan49052 жыл бұрын
Good one sir just😀😀😀 Plz Make more ideas
@paulthomson2375 Жыл бұрын
Excellent work 😊
@buffalo41274 ай бұрын
Beautiful!!!
@chrisabraham87932 жыл бұрын
For a more accurate cut on the circumference i would use a jigsaw with metal blade.
@metalworksph2 жыл бұрын
That's way better. But I dont have that tools to do it.
@lazio7495 Жыл бұрын
Awesome 👍
@duybui1789 Жыл бұрын
Thanks
@dattakamthane2232 жыл бұрын
Sir sheet beding idea
@trinhthang30207 ай бұрын
Good
@caracarametal2 жыл бұрын
what type of grinding wheel did you use to grind down the welds?
@metalworksph2 жыл бұрын
I used 3M flap disc.
@caracarametal2 жыл бұрын
@@metalworksph thanks!!
@alexp5249 Жыл бұрын
👍👍
@royweldingtv2 жыл бұрын
Ayos yan boss buboy
@metalworksph2 жыл бұрын
Thank you boss roy. Daghang salamat boss roy sa supporta.
@royweldingtv2 жыл бұрын
@@metalworksph bisaya ka boss buboy?
@metalworksph2 жыл бұрын
@@royweldingtv tumira kasi ako CDO boss roy 6yrs.
@royweldingtv2 жыл бұрын
@@metalworksph ayos yan boss at may natutunan ka kunti sa salita namin mga bisaya
@laodetea6577 Жыл бұрын
Kelamaan bro
@metalworkweldingfabricator52302 жыл бұрын
Where did you get 3.14 ?
@metalworksph2 жыл бұрын
Value of pi= 3.14
@metalworkweldingfabricator52302 жыл бұрын
@@metalworksph thank you
@user-on6yr2xk1z Жыл бұрын
🤝🤲✍🙌
@robbysamosir61132 жыл бұрын
oke up
@jacklyn8 Жыл бұрын
Sir. Pwede po magtanong? Pag po sa 3mm na kapal ng angle bar. Ano pong welding rod ang ginamit nyo? Salamat po
@metalworksph Жыл бұрын
6013 po maam gamit ko sa video n ito.
@jacklyn8 Жыл бұрын
@@metalworksph pag po ba 3mm na kapal angle bar. 3mm din po na welding rod? O pwede din po ba 2.5mm? Gusto ko po kasi mag diy, mag self study po mag welding. Hehe
@metalworksph Жыл бұрын
@@jacklyn8 pede po maam mas ok 2.5 gamitn pag magumpisa ka magwelding tapos 3mm base plate pag ok ka na. Try nyo na sa mas manipis na tubular. Kayang kaya mo yan.. Goodluck
@jacklyn8 Жыл бұрын
@@metalworksph maraming salamat po sir. Godbless ❤
@CoBugs Жыл бұрын
Why such a complex formula? can be easier. The circumference is L=π*D where D=2*R from these formulas the desired length will be equal to l=(2*π*R)/4. And this is not the limit, you can still simplify the formula l \u003d (π * R) / 2. Because π=3.14159 let's simplify l=1.57*R. In total we have l=1.57*44=69.08mm.
@non1503 Жыл бұрын
Math is cool. but I'd just eyeball it and make it work.
@mladenlazovic3830 Жыл бұрын
what are you advertising!!!!! Music or something else???
@lesbussing7588 Жыл бұрын
The problem with these British videos is the use of metric measurements, we use inches in the US.
@thardyryll Жыл бұрын
The “inch” system is the problem. I am in the states and have been using the metric system for more than 50 of my 68 years. It is simple, accurate and vastly easier to select the next larger or smaller wrench. This would be for car repair, of course. Unfortunately, even though an increasing number of materials, such as plywood, are actually at least partially metric, the construction industry is light years behind. That said, conversion of the numbers in this vid is super easy, as that angle iron is basically 2-inch, 1/8-inch thick.