For cars, definitely mix some acetone, paint thinner or methanol (old school antifreeze) to make it higher octane. There are even videos of people running petrol engines on reducers. As usual, use a biodigestor or sawdust stove (mine burns for half a day) to save time from refueling during distillation. As a sheet metal man, I could turn sheet metal into a tub or make sawdust stoves as wide as I want them to be. I worked with mechanics next door many times by the way.
@stickyfox Жыл бұрын
Sawdust stove is kinda a new one on me! I've used it to fire pottery but for some reason didn't consider it as a generic heat source. If you have any other related keywords I wouldn't be offended if you shared them. Thanks!
@frankmujik9618 Жыл бұрын
Man i have a question for You, since the oil industry in My country was distroyed, we have access to a very low quality fuel, very low octane, and it's mixed with diesel most of the time. It is destroying our engines. My question is, can i mix it with thinner in order to improve the performance of the fuel.
@yevonsama Жыл бұрын
how about use Solar Cooker instead?
@jasonchristopher297710 ай бұрын
@@frankmujik9618 30 yrs experience. Real experience, not internet experience. yes. There are plenty of videos on how to make urr own fuel easily. Also any 190 proof whiskey will add the lost octane or use racing fuel, JP8 jet fuel etc. Too low causes knock, and knock causes u to spend 1200.00 on a used engine to replace the blown up old 1. The oil n gas hit here in Pa around 2007. I left for Marines and Dad said they was hiring anybody they could find cause there was so much work. Now my beautiful country setting is filled with bad roads from all trucks, rent is sky high, u can't drive anywhere and make time cause u always behind a oil, gas well semi of some kind. And ppl getting cancer so much I don't know any 1 who hasn't lost family to it, is going through it, or has died from it. It's alarming. 2 ppl I know personally wasn't feeling well, went to Dr, 1 was in 40s and died on a week of esophagus cancer, 1 from liver cancer, and my buddy Jake lived 6 months after he got diagnosed. It was a small tumor and then just went wild and he wasted away and died 6 months later. That's a very common case here for everyone. Why? All its done is ruin land, lives and made a few rich. That's it. Gas is high, oil products are high and oils in alot of stuff we use daily, rent and homes are insanely high etc. Sad. Very sad. and not a dam thing we can do but just take it.
@JohnDoe-ji5wg5 ай бұрын
Yes you can, @@frankmujik9618! Mix your fuel with alcohol to increase its octane by a bit, mix your fuel with toluene (paint thinner) to increase it by a lot. Be careful with toluene though, that stuff is highly toxic and your car might fail emissions if you mix too much in. Ethanol has an RON octane rating of 109, toluene has an RON of 121.
@mokhtar_One_u_Key2 жыл бұрын
The irony in this is; you have to burn something to have something to burn.
@GaisaSanktejo2 жыл бұрын
I saw a more advanced version like this before, where the creator used some of the fuel created to reduce the plastics to usable fuel. So, it is doable!
@cristianpopescu782 жыл бұрын
You can use Solar power as well.
@mokhtar_One_u_Key2 жыл бұрын
@@cristianpopescu78 The sun is also a kind of burning thing,don't you think? 😎
@cristianpopescu782 жыл бұрын
@@mokhtar_One_u_Key Sure, but it doesnt burn in the night..So you have to store it somehow..
@freeagent4lyfe2 жыл бұрын
Lmao charcoal
@kvhvtke19355 ай бұрын
This is something to keep in your back pocket in case of hard times ingenious way to make fuel
@denniscompton5800 Жыл бұрын
Best one I have see to demonstrate how simple the process is and on a larger scale the flue gas could replace the wood in the process.
@Yettiattack5 ай бұрын
Yes you could replace the initial firing. But you still burning trash to burn trash 😂
@gnavia744 Жыл бұрын
Simple and useful design , congratulations. Easy to do anywhere , a real positive impact to reuse the fossil fuels locked in plastics.
@badchefi Жыл бұрын
After poisoning himself he burns it all for nothing -
@gameyord718211 ай бұрын
@@badchefi lol
@ivarmay36095 ай бұрын
im a plastic manufacturer owner... we dont do this for recycle because of the toxic gases it emits and the contaminating residual that it produce. This is called pirolisis and its very bad. Most plastics can be recycle up to 7 times without loosing much of its carecteristics. Then you disolve them in acid. Not good, but more clean, much more clean
@mzatichilambe3450 Жыл бұрын
I wish there was a way for him to carry out a test that shows if it's gasoline, diesel or paraffin etc and percentages. So far, it's good, but a bit risky to put it in an internal combustion engine! External one it would definitely work all the time. Keep it up, man!
@mahlonkarpaiya25211 ай бұрын
No one would but that on a modern day engine. How ever if fuel from waste. Can't beat that
@wakeupcanadians11 ай бұрын
is it not called biogas or something like that?
@gameyord718211 ай бұрын
it´s made of........ *yes.* (it has all of those things, to separate them you could boil it on a long tube with diffrent metal sheets every meter or so)
@A2J_Tim11 ай бұрын
I dont think he had diesel there, you cant light diesel with a match like that.
@vasterasjonas111 ай бұрын
Cansergas@@wakeupcanadians
@intellectus2826 Жыл бұрын
Loved when the 3rd pot caught🔥on its own 😍
@GrassPossum Жыл бұрын
Being the last one, it contained the lowest boiling point, highest vapor pressure hydrocarbon. No surprise, I was waiting to see which one was volatile enough to have enough gas to catch the flame next door
@giggling_boatswain2 жыл бұрын
This man made pyrolysis (fuel) from all sorts of things - rubber, plastic, nuts, fish, coal, computer radio boards, sugar, Vinyl records, charcoal, sunflower seeds, bird feathers, tangerine peel, cigarette butts and much more. Сhannel - Inventor Adventure.
@mynyasabut Жыл бұрын
wow!!!!!!!
@silviamagni3148 Жыл бұрын
Ñ
@joefather9651 Жыл бұрын
if you’re reading this please don’t use rubber or tires! it make’s extremely dangerous and cancer causing chemicals such as bromine that is very bad for the environment and makes acid rain
@k94536 Жыл бұрын
WOW Doc BROWN
@user-hc2bm9bj7q5 ай бұрын
резина тут не очень подходит так как содержит много серы.
@Theoverthinker81 Жыл бұрын
The process produces about 10% gas which can be used in a feedback loop so no wood needed to burn. You cannot use this fuel (naphtha) directly as petrol because the octane ratio is incorrect. It's needs to be reformed first and ideally additives mixed in with it.
@lepef32 Жыл бұрын
Could this Naphta be used raw but mixed with regular gasoline, like 25% naphta + 75% gasoline ?
@Theoverthinker81 Жыл бұрын
@@lepef32 technically yes only for very old engines and about 10%. However, any mixing would dilute octane and create engine knocking. Old engine without computer control (carburettor) are able use less clean fuels but produce more toxic emissions.
@LogitechXibanga Жыл бұрын
@@Theoverthinker81 yea nobody cares about that, does it work on diesel engines thats what is important screw gasoline those are unrealiable and not very efficient!
@Theoverthinker81 Жыл бұрын
@@LogitechXibanga no, the molecules would be too small for diesel. Car tires would produce diesel using that process.
@lazarusramaube8291 Жыл бұрын
@@Theoverthinker81Dankie Oom,I have lots of tyres
@mietekvictor4218 Жыл бұрын
It's amazing how you refine three different fuels in one process👍
@frenzzie1061 Жыл бұрын
you know difference between the three different fuels?
@danielgattoricci1729 Жыл бұрын
@@frenzzie1061 explicarlo....
@burdock44196 ай бұрын
@@frenzzie1061elaborate
@aznative_2 жыл бұрын
That was a great all-around video. The content was excellent and so was the editing and production. Thank you.
@jean-rosnybelizaire4058 Жыл бұрын
Yes yes brugh
@iuli3244 Жыл бұрын
Great video, You can use the flammable gases to increase burning under the drum
@panchovillaz8004 Жыл бұрын
Is gas
@rogerpouseman25026 ай бұрын
You close the cycle. Nothing is created, it is only transformed and the result is carbon dioxide to contribute to the greenhouse effect! cierras el ciclo .nada se crea solo se transforma y el resultado es dioxido de carbono para contribuir al efecto invernadero¡¡
@alexmacias8658 Жыл бұрын
Que buen video, muy bien explicado para hacer gas y diésel a partir del plástico, saludos desde Colombia 👍🇨🇴
@braydenhardcastle9425 Жыл бұрын
Great video, just learning about this process and you do very well teaching without even having to speak words
@vlaramconnamoryАй бұрын
You are a brilliant guy i like it thank you for posting.🤔😗
@alienwizards32462 жыл бұрын
wow the amount of time and money we have wasted trying to go green while we could all just be doing this instead
@rckc.1719 Жыл бұрын
exactly on point if we go total green what will we do with the tons of waste plastic, ? also i think fuels derived from waste plastic may burn cleaner.!!??
@aidenspooner8893 Жыл бұрын
Well yes but technically no, Upon burning plastic a gas is released that produces sulfur dioxide which is very harmful to both yourself and to the environment. An absence of oxygen must be created to prevent the sulfur dioxide from being created, however after this many other harmful gasses are made. I think lime is used to counteract the acidic gasses made but im not entirely sure.
@finicindustries2787 Жыл бұрын
Great idea. However, please be aware of explosion risks. Highly risky to cut barrels with angle grinder without water in those drums at least quarter full.
@baskelder2650 Жыл бұрын
If you fill a drum to the top with water en let it overflow for a bit you dont have any oil left in the drum
@gangleweed Жыл бұрын
@@baskelder2650 Oil residue coating the inside of the drum even after flushing with water will vaporize with the heat of the angle grinder and a 2:1 ratio is an explosive mixture.....many people have been injured and killed by cutting oil drums with angle grinders.
@danielgattoricci1729 Жыл бұрын
Excelentemente explicado ,a veces lo más simple es lo más exacto....
@marcusjames6425 Жыл бұрын
Awesome video. Note: it's important to wrap thread tape in the same direction you're going to screw the fitting on otherwise when you screw the fitting on it will unwrap the tape like it didn't this video that's why it's sagging. He'll be lucky if any of those fittings hold or seal, I don't think you want what's inside the pipe to leak out onto the fire, big boom.
@davidsexton_904 Жыл бұрын
That was painful to watch after you said something! 😂
@evanreid8653 Жыл бұрын
And it WILL back itself out eventually lol
@ManiacRacing10 ай бұрын
Excellent tutorial on how to make a big mess.
@Rincon00910 ай бұрын
YO!!! YOU explain with no words!! -I understand!! Thank You!!!!
@mynyasabut Жыл бұрын
If you feed back some of the gass to the flame that heats the tank you'll need less wood
@chargermopar Жыл бұрын
That's what I do.
@gilsonoliveiradealmeida5647 Жыл бұрын
O nordeste fechou-se com Bolsonaro
@IshaqIbrahim3 Жыл бұрын
@@chargermopar If you take 100 litters of petrol to heat the plastics how many litters of petrol will the plastics produce?
@chargermopar Жыл бұрын
@@IshaqIbrahim3 It's pretty similar as to weight. I get about 1/2 of polyetylenes as a Diesel and maybe 1/4 as a gasoline like fuel. The rest is waxy paraffins or light gases
@IshaqIbrahim3 Жыл бұрын
@@chargermopar The reason I am asking is to see if there is energy profit. That is if I use 100 liters of petrol. Will I get more than 100 liters of petrol out (profitable) or less than 100 liters which is less profitable?
@earlschultz7880 Жыл бұрын
Love the idea, great video. Question, what is left in the drum? Is it easy to get out? thanks
@fragnicht1734 Жыл бұрын
A dark and crispy Carbon layer, should be easy to Get out
@joefather9651 Жыл бұрын
you won’t have as much if you flush the chamber with co2 before starting the process.
@davidrojasramirez165912 күн бұрын
Excelente video sencillo pero entendible, solo es mejorar el proceso y pasarlo a mayor escala reutilizando el gas final.
@dominicmogridge392011 ай бұрын
thank you kindly for sharing my friend.May a hundred thousand blessings be upon you and yours.mad dog,off grid,West cork.ireland
@workphone421011 ай бұрын
SEEMS TO ME A GREAT WAY TO GET RID OF ALL THE PLASTIC BEING DUMPED EVERYWHERE & MAKE SOMEBODY REALLY RICH, PROVIDE JOBS & TAXABLE INCOME. WIN WIN
@wesamalwesam6895 Жыл бұрын
good job My question is, the first basin collects kerosene, so what does the second and third basin collect? Thank you
@MorningstarNightgod5 ай бұрын
higher octane fuels notice third 1 caught fire from 2nd
@CharlesNewkirk-lb6uh Жыл бұрын
And when you're done you have fresh cook bread excellent
@glywnniswells9480 Жыл бұрын
On a large scale this will be even better.
@mikeconnery4652 Жыл бұрын
Use a rocket stove for heat also add wood enclosed in a container same as the plastic. This will also give you wood gas and charcoal. One more container with wood with a steam inlet and you can have activated charcoal for clean water.
@johnkramer7018 Жыл бұрын
I just hope this can be done on a large scale. There is no doubt that it is possible to turn all kinds of plastic into all kind of liquid fuel. This is the thing of the future. It's not far fetched at all.
@kevinfromalberta Жыл бұрын
It is happening already in Alberta Canada. I think they are close to or already in production.
@johnkramer7018 Жыл бұрын
@@kevinfromalberta! That's a real great sign there. Are you from Aberta Canada? This is very interesting. I wish it was happening a lot all over Canada and the United States.
@kevinfromalberta Жыл бұрын
@@johnkramer7018 yes I am.
@johnkramer7018 Жыл бұрын
@@kevinfromalberta! That's great. Thank you for sharing your story. Thank you for telling me that. I am very happy to hear that.
@jimmatrix7244 Жыл бұрын
You need to clear forests to burn those plastic into fuel using this method!!
@toddlong867210 ай бұрын
I bet your car will love it
@constitutionalrepublican16116 ай бұрын
mine will burn it no problem.
@constitutionalrepublican16116 ай бұрын
id even put it in my international tractor too.....
@toddlong86726 ай бұрын
I like your handle
@billhayward26688 ай бұрын
I think the idea is to put less in landfills and harvest something from garbage. I saw a video doing something similar with tires. I have 400 tires to get rid of and at 10 bucks a tire to dispose of them is more than I care to spend. Great video, thanks for sharing.
@babajaaniloveindia5057Ай бұрын
मुझे लगता है भाई आपने देशद्रोही वाला काम किया है सरकार आपको जिने नहीं देगी,,, लेकिन जो भाई को भारतीय भाई पर फ़क्र गर्व है वो लोग ईस भाई के शान में शानदार सलामी,, दीजिए क्योंकि ऐसे लोग हमारे भारत मां के भविष्य को बहेतर बना सकते है लेकिन अफसोस है आपकी क़ीमत और अहेमीयत कोई नहीं करेंगे,, जल्द ही कोई कंपनी आपको लालच देकर फार्मुला लें लेंगे लेकिन आप बहुत बड़े दील वाले है सरे आम प्राकटीकल करके देखिए
@antoniocarlosmcd Жыл бұрын
muito bom .....caso seja possível faz um vídeo mais explicativo .... sobre a queima da gasolina no motor ..... outra coisa .... ao cortar o latão tomar muito cuidado esse não era deposito de gasolina ou algum outro tipo de solvente .... a pouco tempo um vizinho morreu ai tentar abrir da mesma forma que você fez ,,,, foi um enorme explosão .... só uma dica ...obrigado amigo
@shyamsundarbhadage5419 Жыл бұрын
very good. Calculation of total cost is needed
@homloklebenyterapia97905 ай бұрын
anyone who is even a bit of a pyromaniac knows that plastic smoke is flammable, but burns very sooty.
@travismoore78492 жыл бұрын
I wonder if you can use hydrothermal cracking at 180 degrees C at 100psi in an industrial pressure cooker.
@GrassPossum Жыл бұрын
Even just removing the oxygen, the seals were woeful, will make a big difference, but I was thinking of increasing pressure too. I love the simple proof of concept video though. How far you take it depends on your fabrication skills and industrial chemistry knowledge, but a troglodyte could manage this much so it's encouraging.
@shanesouthard7111 Жыл бұрын
Its important to note that using a grinder on any enclosed container that previously carried a combustible product is extremely dangerous if your container has not been completely drained, and the fumes have not been fully evaporated. Always exercise caution when cutting open a barrel with a grinder. I know for some this is common sense but for somebody who lacks experience this is how you end up on an episode of Ridiculousness.
@doodlegassum6959 Жыл бұрын
Interesting experiment. Thanks
@RashedRashed-786 ай бұрын
Alhamdullah JajajakaAllah for the good presentation
@madscientist39876 ай бұрын
PET fecomposes without liquid. The main product is acetaldehyde. Citation:PET pyrolysis led to a high yield of gas fraction, a low amount of liquids, a significant yield of solid fraction, and a solid residue that remained in the reactor coating sand particles. The main products obtained are carbon monoxide, carbon dioxide, benzoic acid, and acetaldehyde
@garyrock2356 Жыл бұрын
Clever stuff. The residue left in the drum, obviously a lot less material, but does it work out less toxic/harmful than the plastic waste itself? Obviously a lot of wood was burnt to heat the drum to produce a small amount of fuel. You always need to look at the pros and cons of anything.
@TGnM Жыл бұрын
wood can found in the wild technically for free
@Gen_Kael Жыл бұрын
He got a lot of residue because he didn’t flush the tank with CO2. Could have been way more efficient if he did.
@joefather9651 Жыл бұрын
if you use insulated material like ceramic brick and ceramic thread it will hold heat and will energy longer so you don’t need as much material.
@alainvosselman9960 Жыл бұрын
@@TGnM That would be at the expense of nature.. so it still is costly. This heat can be reached with Afghan mirror 'system'. Like an dish antenna covered with mosaic mirrors pointing at one point where a kettle can be placed. The sunlight is reflected by the mirrors and heats the kettle. kzfaq.info/get/bejne/rNyca6l4uK-9ZmQ.html
@garyrock2356 Жыл бұрын
@@jonahcollie8821 Unless you use a steam engine or wood gas.
@mzagasaater8964Ай бұрын
This innovation is highly commendable as it will reduce plastic from the waste stream. However, using fuel wood as a source of energy to heat the plastic and convert it to oil entails going through the deforestation process to acquire the fuel wood. Fuel wood combustion will again emits carbon into the environment.
@got2kittys Жыл бұрын
You can also seal a moonshine still with dough.🍸🍹🍾
@marcosvaleriociencia1021 Жыл бұрын
Maravilhoso!! Brasil!!! Eu fiz rsta experiencia em meu canal!👏👏👏👏👏👏❤❤❤❤😃😃😃😃😃Congratulations of Brasil!!!!
@shadreckchidambo39752 жыл бұрын
Ooh men l like you're short and well explained video probably will do this
@TheOliveboy937 ай бұрын
Too much heat will produce too much pressure and you end up losing fuel and igniting the contents of the barrel. Best way is a controlled source of heat and not a huge fire like this. I would replace the wood with a wick and fuel. Also need to condense the vapour as it passes through the hose. Reduces losses.
@RayS-zh5we Жыл бұрын
Great video thanks for sharing my friend...God bless 🙌
@captainreapergaming8911 Жыл бұрын
Thats really cool, but how do you get the clay off afterwards?
@mardinirm2 жыл бұрын
It is OK., but if you can seal the barrel better will get more liters and decrease pollution.
@krisbergin86285 ай бұрын
Strap one of these to chimney that would already be in use and get double use from the firewood. You could also use a secondary burner under the burn chamber that utilities the gas byproduct with a burner to increase efficiency and decreases the emissions . A Fresnel lens could work well as a heat source too!
@RandomHuman11039 ай бұрын
Interesting idea,but we need to do more testing
@RandomHuman11039 ай бұрын
@Pyrolysis_Tashkent Interesting,but why aren`t we using this in mass production,its soo efficient(we can turn waste plastic into fuel)
@ozgurozan324 Жыл бұрын
Good job ! What are those three liquids you've seperated ?
@GrassPossum Жыл бұрын
Hydrocarbons. Petrol is variations of hydrocarbons. These range from benzene, toluene and various mineral spirits. They'll be mixtures of a few. You can mix and match once you have a few details easily measured with each fraction. Such a simple system isn't really cracking the various fractions though. Something more approximating a fractionating column could be employed on a scale though. The water cooling was hardly worthy of the name. I'd have cooling jackets and running water at least. Also some better seal. The best part of this is the concept is demonstrated at its most basic level. People with the knowledge can improve on this manifold and increase efficiency maybe ten times over without too much effort. Not that much by volume, but some, but above all in separating different BP hydrocarbons at least.
@landrytalom6997 Жыл бұрын
@@GrassPossum ok
@Kristoffceyssens Жыл бұрын
Strawberry, vanilla and chocolate.
@humbertomonteiro67422 жыл бұрын
A good idea, now we need to remove plastic from the oceans, he still has value...
@gustavobalmaceda23462 жыл бұрын
It is not a good idea at all, the amount of energy that must be applied for the reaction to occur is not compensated at all with the gasoline that was created. its always best to melt the plastic and mold it into another object. because either you end up using a lot of fuel either firewood gas or electricity for the conversion. In addition, when you burn you are generating carbon monoxide and dioxide, which pollutes more than the plastic itself.
@GodSpeaksInMath11 ай бұрын
Excellent.. i wonder how fresnel lenses and the sun would work for heating up the drum?
@GodSpeaksInMath11 ай бұрын
I like how you sealed all the byproducts in the drum...
@stevenroberts970 Жыл бұрын
Wot a brilliant way to reverse global warming if only all petrol stations like esso had this plastic recycling facility think thr climate wud be solved
@01Autentic Жыл бұрын
You can put theblast under the barel to recuperate the gas goood video!!
@cybertroncoreas98889 ай бұрын
I strongly believe that anything is possible I would say creating a big steel tank and find a way to use electrical heat by the use of solar pannels , the biggest benefit in this case is that , almost every country around the world has this problem, it would be a very good way of facing this polution problem , and you would generate income by selling the oil for a much cheaper price . Of course this would be an industrial investment unfortunately governments aren't interested on fixing the global plastic proble we face !!!!
@blakestorey481611 ай бұрын
This is cleverly built ❤
@emil.honganmaki54619 ай бұрын
Easier to fill up at the meter. but good video.
@Jamal-Ahmed7863 ай бұрын
The reason why this works is because plastic is made from what petrol and diesel is made from
@szebike5 ай бұрын
Sure lets create some toxic chemicals in the open in the woods without any protection or safety measurements for humans and nature what a good and ecologic idea .....
@rogerpouseman25026 ай бұрын
good contribution to pollution, and release of carbon dioxide in all phases to produce a CO2 concentrate to burn and multiply it even more! buena contribucion a la polucion , y liberacion de dioxido de carbono en todas las fases para producir un concentrado de co2 para quemar y multiplicarlo aun mas ¡¡¡
@85cactus Жыл бұрын
Could you please kindly show an engine running on this fuel? 🤔 The whole concept is interesting but not every flammable liquid is a petrol....
@hayatel2557 Жыл бұрын
I would be more effective if the barrel was place horizontally and the top of the barrel is shaped like a cone with 2 separate hose. One with a gas membrane to power the barrel fire and the other hose with a small diameter to collect the fuel. Increase the water level and add a constant cold water flow to get a cleaner fuel. It uses same process to extract gas petrol and diesel from heavy oil. Plastic is a petroleum product except for bio plastic.
@EvergonPro2 жыл бұрын
What's left in the barrel?
@bradmadisonmitchell37337 ай бұрын
Would be very interesting to know what came out of each container.
@dragan3290 Жыл бұрын
Excellent job 👍👍👍
@vlatkicute9622 Жыл бұрын
For learning the process great video. From economic point of view??? How many wood You burn for 3litters gas? However Great Video. Thanks.
@Zqppy Жыл бұрын
Who measures Gas in Liters?
@schumispecial16 ай бұрын
How would you add wood to your existing gasoline tank?
@stephenalfred30087 ай бұрын
I'm currently working on this project for my BSC program
@thobanijoji5906 ай бұрын
Where can we follow it up or be taught progress
@luciankristov6436 Жыл бұрын
Maintain temps in the pyro reactor is pretty critical or youll produce parfin based naptha. If done correctly you can make diesel fuel after refining the fuel oil produced.
@thobanijoji5906 ай бұрын
do you know how to refine?
@MORE-onProductions5 ай бұрын
Add copper to the last tube. Run it back to the barrel. Let it boil itself
@sethfrazier8287 ай бұрын
I feel like the fumes is what you should really be trying to capture because that is in essence the most pure gas ⛽️ and then those layers should have multiple filters
@mohammadhasn3661 Жыл бұрын
من سورية اقول لكم كل شيئ في هذا الكون هو عبارة عن عملية تضاد زائد وناقص بارد وحار اي بمعنى هذه العملية هي عبارة عن تسخين تبريد وأضف إلى ذلك ليس فقط من البلاستيك نستخرج النفط بل من الأشجار من فحم الأشجار الطبيعي نستخرج الغاز وهو جودة أكثر من الغاز الطبيعي لان احتراق الأشجار طبعا احتراق مع التراب وعملية تخمير ينتج غاز كل شيئ موجود في الطبيعة هو مكمل لنا في احتياجات الحياة حتى الأعشاب..والحديث يطول وشكرا
@KORZDAKRA2 жыл бұрын
very nice 👍 great work 👍 my friend
@rodolfomasiero6677 Жыл бұрын
Complimenti, molto ingegnoso.
@hermanedestinmichel3560 Жыл бұрын
Good job my brother!!
@_Reviewer5 ай бұрын
It is not petrol as such. It is some another polyster oil. Never try it in your car or bike 😄😂😂
@WheresTheFun9 ай бұрын
Cooling at diffrent temps will yeild diffrent fuels. If the 1st one wasent cooled by water it would give a more non combustable fuel. The cooler you have the gasses the more flamable they are. Once cooling gets difficult compressing the gasses would work perfectly and give things like propane and butane
@jadmanjulie8187 Жыл бұрын
what to do with the waste in the barrel?
@aivisabele Жыл бұрын
Just throw it out somewhere. It's India mate :D
@captainreapergaming8911 Жыл бұрын
whats ironic you burn something to have something to burn
@tomhubbard3532 жыл бұрын
I have been looking into this a lot lately, you put a bunch of PETE in your reactor. PETE is supposed to NOT work for pyrolisis, HPDE, PP are types that can be used. Also the door you put into the reactor does not seal so it is letting air in which is not supposed to work IE the plastic burns instead of reducing to fuel.
@bitsofeverything83852 жыл бұрын
I guess you didn't see he did seal it before starting it up, i think PETE generates gas but i'm not certain. I would rather think about refining.
@tomhubbard3532 жыл бұрын
@@bitsofeverything8385 Yeah I saw him seal it up but if you look at it at around 5:44 you can see it is no longer sealed and flames are coming out of the barrel at the "hatch" leak. Im not saying that you wont get a distillate with a leak, just that it will not be as pure or clean. From my research, PETE turns into a caustic gas and a sulfur like substance, it does not pyrolize. I am assuming you are referring to "refining" as in distilling the crude fuel produced down into it's distillates IE gasoline, kerosene, diesel etc.? I am in the process of building a reactor as I write this, it is about 90% done now and I am almost ready for my first run, then refine my design.
@bitsofeverything83852 жыл бұрын
@@tomhubbard353 You right there, you refreshed my memory, i expected the catalizers at the end of the process (and yes that's what i was referring to) should take care of the sulphur, i'll have to google caustic gas. I seen quite a nice video of a enterprise trying to sell their product, if the specifications correct and one wouldn't want to mess with it seems as an acceptable option, however at long term one would need to build it's own i agree. My point with this last part is that they detailed quite well the way their apparatus work.
@davidwillard73342 жыл бұрын
Forty four Gallon Rusty ! Drum ! The Reactor ! Won't LAST ! That ! Long ! Anyway !!
@tomhubbard3532 жыл бұрын
@@davidwillard7334 True, mine is made of SS, considerably smaller, probably five maybe seven gallon capacity. Even it has a life expectancy. I am currently "pre-melting" IE flattening and condensing my consumables, plan is to build a shredder after I get the kinks worked out of the reactor/condenser/distillery.
@johnarendse1288 Жыл бұрын
hi this is very interesting .my qeustion is what fuel is in the thrree cans and in what order does it escape from the reactor.
@Twogreenfeet9 ай бұрын
The thickest most viscous come out 1st.
@yevonsama Жыл бұрын
i think you can combine this system with a Solar Cooker. You will not need to use wood to burn anymore.
@ilgiusto688510 ай бұрын
O ,come nel mio caso, si può usare la corrente gratis del mio impianto fotovoltaico, di giorno,dopo due ,tre ore le batterie sono cariche, per altre 4 o 5 ore ho 400 wh gratis !
@Twogreenfeet9 ай бұрын
Whats the highest temp you have achieved with your solar cooker?
@ilgiusto68859 ай бұрын
@@Twogreenfeet difficult to answer....I speak in principle, burning wood to obtain fuel which will then be burned seems very inefficient and polluting to me, at least if we eliminate a harmful part of the process it is better...👋👋
@Twogreenfeet5 ай бұрын
@@ilgiusto6885low power fresnel lens
@stjepanmatanovic2555 Жыл бұрын
Most useful video on the internet
@sciencetribune6355 Жыл бұрын
Great job done brother , owo.................go ahead
@shakesmarley47548 ай бұрын
You still need to put it through a catalytic cracking unit and then fractionally distill it id even pyrolyse it a few time over and same with catalytic unit till there’s no tar at all then you can split the longer chain carbons(diesel) and shorter chain carbons(petroleum) usually you you would add some other additives as per your gas type but it’s not as simple but also not all too impossible
@thobanijoji5906 ай бұрын
Do you have a book or link or video, anything that can teach me that process
@bryanst.martin7134 Жыл бұрын
Sri Lanka needs this.
@sbusisosthembiso5797 Жыл бұрын
We need this in south africa 🇿🇦🇿🇦🇿🇦🇿🇦🇿🇦
@maurerdavidji007 Жыл бұрын
Be careful you need wood
@joefather9651 Жыл бұрын
@@maurerdavidji007 not necessarily, just any source of significant heat. if you insulated it you wouldn’t need as much fuel
@lamiaalamiaa398010 ай бұрын
What is the paste that is applied to the barrel opening?
@GradeGuru-8 ай бұрын
Looks like flour
@hunting.123411 ай бұрын
How much plastic is needed for 1 liter of fuel?
@Twogreenfeet9 ай бұрын
It looks like about 40 gallons of uncrushed or shredded plastic soda bottles made about 1 litter.
@gameyord7182 Жыл бұрын
is better to use ice to condense everything rather than only water....
@ericgrajeda26714 ай бұрын
Can you make plastic into Ethanol Gas or E85 or just Bio Diseal ?
@refinersoduro8186 Жыл бұрын
can you use this for a car?
@GrassPossum Жыл бұрын
Depends on the engine. Then you'd experiment with various mixtures of the different fractions, maybe a bit of some additive and no reason why not. It would take a little experimenting. I used to run a work van I used for photocopier services in the liquid copier days and the developer, which was isooctane would run the van when I ran of fuel on those outback roads and long trips as happened sometimes. Engines are more finicky now. Older engines with carburetors that can easily be adjusted for the mixture of air and fuel.
@panchovillaz8004 Жыл бұрын
Yes plastic cam fron petroleum gasolina cam fron petroleum. Is same
@bradlys497810 ай бұрын
Your Teflon tape is not working because you wrapped it in the wrong direction. need to wrap it so it tightens as it threads in, not loosens as you thread it.
@pattwidale4045 Жыл бұрын
KA - BOOM!!!
@khalaffzihni6657 Жыл бұрын
IM HERE TO GIVE SOME FREEDOM🦅🦅🦅🦅
@mirza-sons Жыл бұрын
Nice idea 💡
@quinton39975 ай бұрын
Are are you stopping it from turning back into a solid after cooled off