Hummer H3 Water Pump Replacement - How to - Water Pump Replacement Hummer H3

Рет қаралды 3,179

7 ай бұрын

#mikesmancave #hummer #hummerh3 #generalmotors #howto #howtovideo #toledo #toledotools
Hummer H3 Water Pump Replacement - How to - Water Pump Replacement Hummer H3
Contact me at : mikesreviewvideos@gmail.com
Other Hummer Videos :
H3 Viscous Fan Removal : • Viscous Fan Removal - ...
Hummer H3 Fuel Economy : • Hummer H3 Fuel Economy...
Hummer H3 Battery Upgrade : • Hummer H3 Battery Upgr...
Why I Drive a H3 Hummer : • Why I Drive a H3 Hummer
Hummer H3 Service Indicator Reset : • Hummer H3 Service Indi...
Hummer H3 Stereo Panel Removal : • Hummer H3 Stereo Panel...

Пікірлер: 29

@joshuawiggins6637 4 ай бұрын

Helped me out a lot I know what to do now instead of going in blind

@MikesManCave 4 ай бұрын

IT's not that hard, as long as you have the correct tools I have mentioned. 👍👍

@CanadaLifeVlogs Ай бұрын

Very good video

@MikesManCave Ай бұрын

Thanks for the comment, much appreciated, I was not even going to make a video on this, but then saw how bad the others were one literally showed the old water pump in position and the flipped to the new one installed.

@bluesteel5841 6 ай бұрын

Very good thank you. I needed this info. Best one I seen on KZfaq..

@MikesManCave 6 ай бұрын

Thanks for the feed back, I wasn't even going to make this video till I saw how bad some of the other were. 🤣🤣

@hugeslacker 7 ай бұрын

Thanks for making this video! I am ordering my water pump right now and wanted to make sure I had everything I needed.

@MikesManCave 7 ай бұрын

Yeah you will need the fan spanner. The rest is pretty basic.

@hugeslacker 7 ай бұрын

@@MikesManCave I ordered a 36mm spanner. Hopefully it's long enough. Otherwise I'll have to weld something to it haha

@MikesManCave 7 ай бұрын

You will probably have to grind it down, I had a 36mm spanner, but it would not fit into the gap, and it was too expensive to grind down, but some are more slim line. See how you go. @@hugeslacker

@hugeslacker 7 ай бұрын

@@MikesManCave This one is the thickness of a bicycle pedal wrench... It was off amazon labeled as a viscous fan clutch wrench. I have a grinder though if I need it!

@MikesManCave 7 ай бұрын

@@hugeslacker That one should be fine.

@bridgetrobertson7134 5 ай бұрын

I love Aussie car repairs. Don't let them replace you.

@MikesManCave 5 ай бұрын

Ok.

@TheRopenNetwork 4 ай бұрын

Good vid, but the belt was difficult to follow. Do you remove it completely? We have a couple of H3T's in our fleet. Same process but very difficult.

@MikesManCave 4 ай бұрын

check 14:30 minute mark

@ajsalazar82 Ай бұрын

My fan moves when I try to loosen.

@MikesManCave Ай бұрын

Need the right tool and do it exactly as I show it. Make sure you are turning it the right way. There is no other way really that I can think of.

@thedealkingz2606 3 ай бұрын

32 are 36

@MikesManCave 2 ай бұрын

Sorry I have no idea what that is supposed to mean.

@thedealkingz2606 2 ай бұрын

@@MikesManCave Is was the size of wrench you used

@thedealkingz2606 2 ай бұрын

@@MikesManCave I got the 36mm on the way

@MikesManCave 2 ай бұрын

@@thedealkingz2606 Yes, you need 36mm.

@MikesManCave 2 ай бұрын

@@thedealkingz2606 That's the one you will need, it's not a hard job, and well worth doing.

@MrPhlypc Ай бұрын

Wrong coolant should have dexcool

@MikesManCave 22 күн бұрын

Interesting, I will look into that.