Mitsubishi Colt 1.1i Water Pump Swap incl. V-belt
Рет қаралды 10,538
3 жыл бұрынTerrible noise after cold start came out of the engine. The root cause is in my opinion after multiple v-belt tesioning procedures worn out v-belt and water pump that turns kind of hardly, even though seals. The belt pulley is also trenched in from the v-belt. We can see at the beginning of the video, that the belt was sliding around the pulley, not able to drag it with the same speed.
TOOLS:
set of normal sockets
5/16 torx socket
small & big ratchet
drain box for coolant
jack up
jack stand
sand paper
paper towels
gloves
MATERIAL:
new water pump + new gasket
G12 ethylene glycol based coolant concentrate
demineralized water
new V-Belt recommended
OTHER VIDEOS ON COLT:
Alternator swap
• Mitsubishi Colt 1.1i -...
Spare wheel change very fast:
• Mitsubishi Colt 1.1i S...
Air filter change:
• Mitsubishi Colt 1.1i A...
Headlight change:
• Mitsubishi Colt 1.1i H...
Pollen filter change:
• Mitsubishi Colt 1.1i -...
Spark plugs change:
• Mitsubishi Colt 1.1i S...
Rear shock absorber change:
• Mitsubishi Colt 1.1i -...
@walter_texas 8 күн бұрын
We still need more videos about Colt
@REBUILDLab 8 күн бұрын
Hi, something is comming. Clutch, valve clearances etc. But it takes time. What do you need? Thank you
@zgabeartzaiftodie8615 3 жыл бұрын
Big like mate and thank you for sharing the pump replacement procedure ,my little monster started squeaking just like yours
@REBUILDLab 3 жыл бұрын
Yes, it is bad. But what I thought about that noise is, that it came really because the belt was sliding over the water pump pulley...so what could be possible is to roughen the pulley, i is all polished from the belt, maybe with a file first...no idea if that will work, but it might :)
@klemson84--92 3 жыл бұрын
More videos from the repair Mitsubishi Colt :)
@REBUILDLab 3 жыл бұрын
Hi, something about stabilizer will follow :)
@xinwenhe1177 11 ай бұрын
Thank you for charing. You did good job. We need more about colt vidéo.
@REBUILDLab 11 ай бұрын
Thank you very much!
@modi4363 3 жыл бұрын
We want more videos please! (Fuel filter,obd location,gear knob replacement,dash clock removal....Great job sir Big Like and subscribe!!!
@REBUILDLab 3 жыл бұрын
Interesting ideas, thank you for that, I will try to find time also for these. What is bothering me now is that this engine has no hydraulic valve clearance adjusters and noone looked over the valve clearances for 160.000 km. So I think I have to check that first.
@modi4363 3 жыл бұрын
@@REBUILDLab wow sounds good! Good luck continue doing this great job! Thank you for helping us
@thierrypetitniot5603 Жыл бұрын
Super bon tuto et bien expliqué un grand merci je m'abonne
@REBUILDLab Жыл бұрын
thank you very much thierry
@sebastian31182 9 ай бұрын
Super gemacht danke
@REBUILDLab 9 ай бұрын
Gerne! Bin froh, dass es gefällt 👍
@sebastian31182 9 ай бұрын
@@REBUILDLab ja super das bekomme ich auch hin. Solche Videos sind sehr viel Wert
@calibra66 Жыл бұрын
Tnx for the share...i fixt it also...
@REBUILDLab Жыл бұрын
Glad to hear that, You are welcome
@denaldobrakaj6846 Жыл бұрын
Hi, thank you for sharing great content. Could you please tell as what is the size of the socket that you use? it doesn't show good on camera.
@REBUILDLab Жыл бұрын
13 for the alternator I think, 16 for the journal bolt, 5/16 torx for the pulley
@Frillar 2 жыл бұрын
do you know, on the 2010 cz1 1.1 does it have a timing belt or timing chain? there is conflicting information when i search online.
@REBUILDLab 2 жыл бұрын
Fu, the 1.1i that I have has a timing chain. Don't think that it changed till 2010...
@johndoe4920 2 жыл бұрын
Nice i wonder where is the termostat i cant figure .
@REBUILDLab 2 жыл бұрын
Hi, you can see it at the alternator swap at approx. 5:30
@MadiliaSarwary Жыл бұрын
my mitsubishi colt rmp go high to 2500 when cold start and after 5 minutes or 10 in gos down to 850.. Do you maybe now whats the problem>?
@REBUILDLab Жыл бұрын
Hi, tricky, you have to probably chceck the mass airflow sensor, also clean the throttle body and check for vacuum leaks/broken suction hose etc. But the real problem really I don't know, you have to go for diag, it could be also some faulty sensor that makes the engine think it has to tev up so much. Sorry and good luck
@MadiliaSarwary Жыл бұрын
@@REBUILDLab Thank you really much for response i will try to check everuthing step by step!
Braincatchers
Рет қаралды 14 МЛН
АвтоСтронг-М
Рет қаралды 107 М.
Dynodaze Honda Tuners
Рет қаралды 14 М.
ВаньОк Ворона
Рет қаралды 6 М.
Андрей Флорида
Рет қаралды 14 М.