MORE POWER!!! Chinese Atv Upgrade!

Рет қаралды 30,913

Жыл бұрын

MASSIVE UPGRADE FOR THE ATV! #atv #smallyoutuber #small #offroad #wheelies #torque #wheelie #125 #subscribe #watch #low #crawler #upgrade #diy 125cc Tao Tao Sprocket Change, stock 45 tooth to a aftermarket 60 tooth, major improvements! 10/10 recommend top went from 31mph to 26mph. I got a Front sprocket on the way will make a video with that as well. Here’s the link to the sprocket I got on here remember to hit subscribe! New videos every week! www.amazon.com/gp/aw/d/B079C1... the best chain to use www.amazon.com/gp/aw/d/B07XWP...

Пікірлер: 47

@savoeungkep8506 9 ай бұрын

I love my mustang

@zandylanier646 Жыл бұрын

Da hawgz!!!!

@makarennalacourt8053 Жыл бұрын

i bought the parts you put in the links but besides having to drill holes around it, what did you do with the center holes? Because its smaller than the original. Did you do anything to the center hole? I have an xpro 125cc

@dahawgz Жыл бұрын

The center hole shouldn’t matter! Unless it’s to small where it won’t slide on the axle itself, make sure you get really good drill bits because that sprocket is tough! Also I used vice grips and clamped the 2 sprockets together to creat a guide to drill the holes easier

@gr3513 11 ай бұрын

I definitely gotta try the 60tooth did you lose any clearance?

@dahawgz 11 ай бұрын

I recommend changing the front sprocket first, and yes but it don’t hang up on anything

@LTFT83 6 ай бұрын

are those the factory control arms? if aftermarket what are they come off of?

@dahawgz 6 ай бұрын

Factory

@keithshugars9184 Жыл бұрын

Not sure if you would know but would this sprocket work on a Coleman 125ut ? I believe it’s a tao tao just different badges

@dahawgz Жыл бұрын

Yes you still may have to drill holes though! I would just do a front sprocket change! I have a video on that

@brookcaldwell8816 10 ай бұрын

If I don’t change the front sprocket and only the rear will it still have the torque to pull up hills and stuff better?

@dahawgz 10 ай бұрын

I would recommend changing the front sprocket first, you will notice a much bigger of a difference doing that one! Also it’s way easier and cheaper then doing the rear! Thank you for watching!

@cmany 4 ай бұрын

Did you have to add more links to the chain?

@dahawgz 4 ай бұрын

@cmany 4 ай бұрын

@@dahawgz ok cool wanted to make sure

@twoothemoon Жыл бұрын

Will this work for the Tao Motor 110 Boulder B1 Kids ATV? It has very little torque, literally going up a slight hill makes it stop.

@dahawgz Жыл бұрын

I would change the front sprocket first! Do a 10 tooth front sprocket! It will give you way more torque!

@Jimbolo619 10 ай бұрын

@@dahawgzwill you need a different chain if you go with a smaller front sproket?

@dahawgz 10 ай бұрын

@@Jimbolo619 not if you get a 428 sprocket no

@brycekear7322 Жыл бұрын

What size tires are on it.. my sons are smaller.. thanks man

@dahawgz Жыл бұрын

Those are the stock tires which are 18 inches in the rear and 19’s in the front, smaller tires will make the gearing even lower!

@dahawgz Жыл бұрын

I got videos Will this same fourwheeler on 27’s, 30’s and 32’s haha check them out thanks for the comment!

@brycekear7322 Жыл бұрын

Well dangit lol my sons is the 3 lug may have to do conversion.. so you have the 60 tooth on the rear.. I just ordered an 11 tooth I heard 12 or ten but found 11 in the size bore.. do you think if I did more teeth out back it would mess up the gears.. and what tooth do you think.. he likes to go fast haha I ordered a new card and ignition and that but thought I'd ask bout the rear sprocket and what size you think would work and where to find one at least in the bore I need I know the rear axle is the same 22mm size I'm pretty sure.. but idk what fitment I need.. any help would be great..thx man!

@dahawgz Жыл бұрын

@@brycekear7322 you could still mark and drill out holes on a new sprocket to adapt it to work on yours, and yes they do go to fast! I don’t know why they gear these fourwheelers so high from the factory! It’s crazy, there’s no torque at all! I haven’t have to deal with a 3 lug yet but you should be able to drill holes to make it work, just get some good drill bits! And it all depends what tooth he has on the back now! A 60 on a 110cc is probably over kill lol

@dahawgz Жыл бұрын

@@brycekear7322 I feel like you will get more out of changing the front sprocket then the rear, it will make the motor not have to work as hard to spin that big gear in the back, some of these smaller motors don’t like spinning them bigger rear sprockets, also it will be easier and faster changing the front one out! I have a video on that as well!

@erickcrist6086 2 ай бұрын

What sprocket did you use

@dahawgz 2 ай бұрын

Link in the description

@user-or5xq8zj2m 9 ай бұрын

I like to no how to install a sugared lighter on atv 125cc

@user-tz1jy7cu7f Ай бұрын

It’s know but good question

@derrickthrash4973 7 ай бұрын

I have a 150 4 wheeler and I am trying to make it faster what can I do

@dahawgz 7 ай бұрын

Smaller rear sprocket, or bigger front sprocket

@derrickthrash4973 7 ай бұрын

@@dahawgz got a stupid question where is the front sprocket

@garybrady7245 7 ай бұрын

No it's more teeth on the rear and less teeth on the front

@kar21ol96 6 ай бұрын

@@derrickthrash4973follow the chain🤦

@alfredovelazquez3004 Жыл бұрын

Da hawgs can u help me i have the same atv and when i go fast the chain falls of

@dahawgz Жыл бұрын

There’s a way to tighten your chain on the back, you have to loosen 4 bolts then tighten your 2 chain tensioner in the middle, I’ll have to make a video soon on it! Hope this helps! Thank you for the comment!

@alfredovelazquez3004 Жыл бұрын

@@dahawgz thank u

@garybrady7245 8 ай бұрын

Make sure it's straight with the front sprocket too. Stand back and look down the chain and see if its straight along with the whole rear axle, make sure it looks straight with the vehicle and motor