This channel is so under rated, you guys do so much for the racing community. I look forward to the day when Motion Raceworks is as big as Summit or Jegs.
@MotionRaceworksOfficial3 жыл бұрын
super appreciate that man.
@Hitycooking3 жыл бұрын
kzfaq.info/get/bejne/mch2draarM2rpmin.htmlui
@danielpotts96222 жыл бұрын
FACTS.. Absolutely awesome group of guys
@enermaxstephens105110 ай бұрын
@@MotionRaceworksOfficial It would be really cool if the catch can had a way to see in. Like a line down the side, similar to an oil jug where you can tell how much oil is left in the jug. Even just a sight glass may be enough, if it was placed midway between the top and bottom of your can. You could check every once in awhile with a light or something. Then if you saw oil you'd know you had some kind of problem since the catch cans don't usually fill up.
@jasonpatterson9473 жыл бұрын
I have 0% of needing to know this. But, I enjoy learning and hearing Doug talk. 🤣😂🤣😂
@franknbeans36513 жыл бұрын
When we first started to run Methanol through the big block in our drag car, our crank case ventilation was inadequate. We found out that it can be very dangerous. Driver side valve cover (cast aluminum) exploded sending pieces into the fender and fiberglass hood. Could have been a bad deal had someone been leaning over the fender with the hood up. By the next weekend we had a crank case pump never had a problem after that. This was well before Motion Raceworks came along. But lesson learned is that Doug is right and that crank case ventilation is very important and to make sure you have a good system in place.
@laa0fa5022 жыл бұрын
Running a PCV valve?
@rancherodave8 ай бұрын
Probably a vacuum pump system that is driven by the drive belts. Just put one on my 410 ford cleveland stroker.
@gregcombs15733 жыл бұрын
Vacuum pumps- how they work and how they attach. (I know that's more of a full-on racecar deal, but it would help guys tremendously)
@crfrider20052 жыл бұрын
This
@ltsnotspill68462 жыл бұрын
I whole heartedly second this! Please!
@danielkohler3458 Жыл бұрын
This
@normenderle5502 жыл бұрын
These tech tips are dynamite for us guys that are getting back into the performance scene, thanks for the clear explanations.
@TokenTombstone2 жыл бұрын
Just a couple days ago Cleetus told us to put the catch can vents toward the front of the engine because of the G force during acceleration tends to push oil out the back of the covers. You guys need to get on the same page about this stuff.
@GorhamWorks2 ай бұрын
The air/oil film finding a way out, 100% can confirm. I have a baby 700 hp BBC 540 thats NA and had the PCV vented to the intake. Idling, around town driving nothing and not a big deal. But when giving it the go pedal, oil was pushing out the filler cap then running off the back of the engine and making a mess. I'd also get puffs of white smoke too from it being burned in the engine. First build I've done at this power level, learning as I go, and solving problems as they come up. I ordered one of these cans because the baffling and am excited. My first Motion Raceworks product. Love that you sent an email with how to setup and the video was full of great information. I didn't even think about if you're venting to the intake how it could throw more air in, mess with your AFR and need tuning to adjust the top in. Cheers!
@mdtransmissionspecialties Жыл бұрын
Made one at work about 8 months and did some nice baffling in it. Man the difference in the cleanliness in the intake when I did injector change for my mass air swap. in my 96 351w powered f250 the milky yummyness and my dry filter tells me I did a good job 😁 thank you for another good video.
@boostnhoe3 жыл бұрын
I was so interested in the this tech Tuesday and my wife says "is that the guy from guardians of the galaxy". I said who she said "kraglin" from guardians of the galaxy 2. I looked it up and compared your voice to his..... now I can't unhear it. Great tech Tuesday. Ahmad
@beatersnbondo20972 жыл бұрын
I'm just starting out in no prep. I love how I can watch Doug's videos and then feel confident in what I'm doing. Very good way of explaining things so we can understand. Great job guys!
@trentongulley66413 жыл бұрын
Many people have small oil leaks they cant figure out because they aren't letting their engines properly breathe and have bad crankcase pressure making the oil push out anywhere it can. I have a supercharged Camaro that made 753whp but I had large amounts of oil bubbling and fumes coming out of the little breathers I had for each stock LS3 valve cover. I also had oil coming out of front main seal multiple times. Found out that I needed to allow engine to breathe better by plugging up the little pcv ports on both stock heads and getting bigger breather lines on each valve cover to reduce pressure. My oil leaks were fixed after that and now that I learned that I bought 2 Motion Raceworks breathable oil catch cans with a -12an setup for my new engine.
@redneck_ridge_reptiles3 жыл бұрын
Can't wait to see you guys on race week 2.0!!
@chrisobrien93343 жыл бұрын
Great episode Doug. As I’m now going Turbo LS Is very good to have this type of information. Thanks m8. Support from Australia 🇦🇺
@MotionRaceworksOfficial3 жыл бұрын
Thanks Chris! If you ever want our catch cans Warspeed in Sydney, Australia carries them on the shelf!
@trentongulley66413 жыл бұрын
@@MotionRaceworksOfficial Make sure you guys start sending out mass quantities of parts to them as I heard their out of country mail system is being shut down for covid reasons.
@jamestone2652 жыл бұрын
Catch can are good for ALL engines. I’ve had a Ford Performance on my 5.0 F-150 since new in 2018 and a Moroso on my wife’s 2015 Honda Civic since since 2017. There is ALWAYS oil in them when checked. My LSR engine has had a vacuum pump for 25 years and because the engine has close to zero leak down the container has only had water condensate in it.
@SixOhhGeeTeeOhh3 жыл бұрын
Just installed your billet catch can and valve covers, high quality parts for sure
@kygator13 жыл бұрын
Well after talking to you guys last week about this exact product I guess I'll be ordering soon for my 21 camaro... 😎👍
@cecilsabourin9462 Жыл бұрын
Just fantastic guy. So well explaned and understood. just purchased a catch can system for me '92 chev. 1500. this is exactly what i needed,thanks for this expert info. I,m ,now ,a subscriber.
@maximusvonce13818 ай бұрын
Exactly how i do it on my 68 mustang fuel injected 438windsor street strip car. Run 2 Moroso baffled open breathers to a catch can with filter on top. I still occasionally see oil sneak out between breather and valve cover seal, but nothing major. Both my moroso breathers have a filter inside of them and they are baffled. Best breather design i have yet to see. My AFR valve covers have a small baffle over opening but nothing like the valve cover baffles in video. I see steam coming from catch can filter so the system works well. Its a borderline race motor on the street.
@m.pietro90877 ай бұрын
Thank you for the video, it was very informative. My car has 440 engine with a mild cam, it has a PCV valve, in order to use a catch can should I delete the PCV valve? Thank you.
@stevemacdaddy99092 жыл бұрын
Great video guys. I love the information. When I build something. You guys are the ones. MOTION RACEWORKS
@ryanwells20803 жыл бұрын
Thee most badass company right here!!!!!
@NUT84G2 жыл бұрын
Appreciate these videos Doug, Doing LSA Swap here in Australia, buying your parts direct from Troy at Warspeed, this video has answered a question for me... now to order some parts!! thanks mate
@jasonstrester Жыл бұрын
What happens if you forget to empty your can? Will it damage your engine? Or just leak out the vent or blow a seal?
@dougbeckwith7683 жыл бұрын
I know this is probably overkill, but it's my line of work, and I see things a bit different. For instance it would be nice if you could incorporate a flow rate indication on your catch can for a visual reference. It could be used for an indication of clogged/pinched line or an over pressure issue. I imagine one day, if it is accurate enough, a bench racing conversation comparing the CFM created on a stock motor to a more enhanced version of said motor. Let me know if you need a hand with the instrumentation side of it.....
@KCadbyRacing3 жыл бұрын
Since there's a ton of variables it would be easier/better to monitor crankcase pressure and many racers already do that.
@dougbeckwith7682 жыл бұрын
I was just trying to kill two birds with a single stone.
@TheReinoPaasonen15 күн бұрын
How about running small line from bottom of the catch can to back in the oil pan?
@BlackOpsGarage27 күн бұрын
Could you please send me a pic of how your lsa's vacuums are either plugged or utilized?
@katemcswan76273 жыл бұрын
Love the product but just wondering about volume of the tank, in Australia we have to run a 3 litre can for circuit/track applications. Do you have a bigger one? I’m having trouble with my my new LS putting about 2 litre into my can over the course of a weekend.
@HemispheresWines4 ай бұрын
I was running a line from the PCV to the catch can and then other from the vacuum back of carb. Sounds like I don't need a PCV and to plug the vacuum on the back of the carb? Thank you!
@r.arabian3056 Жыл бұрын
Nice product and video. Just ordered one.
@robhatezit50562 ай бұрын
Hey mate im from Australia 🇦🇺 and currently running a worked 6ltr v8 in my Holden commodore and im constantly getting fumes coming in to the cabin and was wondering if this catch can will fix the issue thanks
@Canadianchucknorris692 жыл бұрын
Another great Video Doug, I might have to upgrade at Raceweek!
@aserrao434 ай бұрын
Does the filter need to be oiled or are they dry filters?
@stranglehold99910 ай бұрын
I've heard the L8T and other Gen V engines need the additional vacuum from the intake connection with a more traditional catch can to effectively evacuate the vapors from the engine. Thoughts?
@burneswhitehead3020 Жыл бұрын
Thank you for the info. Just got my first supercharged ride. Mabe i can save the motor it was not set up right when i purchased it
@genemounce83022 жыл бұрын
I can't wait until I have a nice enough engine to add one of these. lol
@kariannestudeman19093 жыл бұрын
I was hoping you would say something about PCV valves on OME? cars to explain at an even more basic level, I hear people say "the engine lights on be cause they want you to change the pcv valve, but their just trying to make money" Is this at least kinda on that same though line, or am I wrong? Oh by the way you guys rock!
@howabouthetruth21572 жыл бұрын
I think ya meant "OEM" ( not "OME" )........or am I mistaken? OEM stands for "original equipment manufacturer". When you buy replacement parts for your factory original vehicle, certain parts available at auto parts stores are listed as "OEM" parts, meaning they are satisfactory parts with the same spec's as the original part. ( at least they are suppose to be ) On factory original engines, it is very important to replace a PCV valve once it has become all gunked up after a long period of use. Because once a PCV valve becomes dirty & clogged up ( even partially clogged ), your valves, intake, and combustion chambers will start getting all sludged up, resulting in poor performance & economy, and shorten engine life.
@Steve828642 жыл бұрын
keep up the good work !!!
@alfenner3309 Жыл бұрын
Best video on this I have seen- I have an 06 mustang 4.0 v6 that has been supercharged (root style) off of a 04 lightning. In order to mount that sc on the intake, one had to be fabricated to do that. So saying that. The passenger side pcv and drivers side, I think is is called a ccv are both not connected with hoses as they normally would be in stock form. So, I'm looking for a scenario that would best work for this set up I have, please. Other info. - egr has been deleted -no intercooler or heat exchanger -no meth. I'm working on this -car dynoed at 380 rwhp I also have a 2015 chevy Silverado 1500 LT 5.3 flex fuel. I'd like to add a catch can to this as well. I live in cold MTvand I have heard running these can be an issue in colder weather. Is the something additional I can do in the colder months? Your help would be greatly appreciated. Thanks
@DirtySideGetsDown2 жыл бұрын
I'd like to see a tech tip video on running functions on switches. ECU's these days have the ability to control multiple fuel pumps, electric water pumps, intercooler fluid pumps, etc. Why are people still running all of that stuff on manual switches that can be forgotten?
@hunterallen12802 жыл бұрын
I’ve got your billet valve covers and two of your single loader catch cans, one venting to each valve cover on my boosted 416” that seem to smoke a little more than my liking, any suggestions or live with it with that kind of cubic inches
@ScoutYa-cg5sd7 ай бұрын
So this same setup applys to 6 cyl aswell yes? Wanting/needing to put a catch can on my is200 was wondering if all was needed to be done was attach a hose to my pcv valve and the other hose to the exhaust side ventilation correct?
@MichaelNowell7246 ай бұрын
Is it normal for the catch can to smoke a lot at idle?
@alundrasrt25 күн бұрын
Hi, same problem mate. Do you solve it?
@djrednitro4116 Жыл бұрын
When I installed the catch can with the filter, there was a stiffing sound and vacuum leak, I had to remove that filter on top of the catch can but I don't understand why it was provided
@jacobschillig72902 жыл бұрын
Would you recommend one on a stock 6.0 Silverado that tows a lot? Would baffled valve covers be needed in this situation?
@M3MPH1SM0J02 жыл бұрын
For longevity purposes any engine can benefit from a catch can. It helps prevent oil from being recirculated back into the engine in places that oil doesnt need to be. There are different kinds, such as those that dont actually vent the pressure, but simply collect the oil and send the pressurized air back into the manifold, which maintains your factory emissions system.
@duasobA Жыл бұрын
great informative vid, 1 question. would the vented catch can decrease the engine pressure? thanks
@JohnRoberts713 жыл бұрын
Great content thanks for sharing, very informative
@jasgap Жыл бұрын
For straight 6, do you block 1 of the ports? Or is there another version of the product?
@megamanmojo3 жыл бұрын
i used a pcv style catch can on my 402 pro procharger gto it blew the front crank seal off the front cover, switch your billet valve covers and catch can and problem solved!
@MotionRaceworksOfficial3 жыл бұрын
Dude that’s great feedback! Mind sending us those details in an email to socialmedia@motionraceworks.com
@megamanmojo3 жыл бұрын
@@MotionRaceworksOfficialof course
@damiangabiola2609 Жыл бұрын
Dunno about you guys but I'm just baffled after this video.. jk really great informative video series!
@joshwynn18369 ай бұрын
What's the best way to pull a line off of stock valve covers? I'll be right around a thousand whp. I don't want to pay 400 for a set of cheap valve covers..at least not quite yet!lol but, I do want to add a can in my boosted 99 Camaro!
@super10797 ай бұрын
Do you have a video for a sbc not LS motor and how would you run it ?
@408dodgeram Жыл бұрын
I've been running an header evap system but my new setup doesn't really allow for it. Could I run this instead
@antoniobarrientos1230 Жыл бұрын
First God bless you, where I get a catch can like that, thanks.
@Justls1v8parts4 ай бұрын
Thanks for video
@Justls1v8parts4 ай бұрын
With valve covers is this from oil can filling points
@alundrasrt Жыл бұрын
So oil vapour pass through by the filter too?
@adeptpeasant61613 жыл бұрын
Would it be possible to create a vacuum in a crankcase to minimize this problem in the first place by a vacuum pump of some sort?
@PredaFran3 жыл бұрын
you can get a vacuum pump, they are used with dry sump systems and just used to help with piston ring sealing, a properly functioning PVC system should work just fine tho
@adeptpeasant61612 жыл бұрын
@@PredaFran I would think that would be ideal under boost conditions but I like the KISS principle. Keep It Simple Sir
@PredaFran2 жыл бұрын
@@adeptpeasant6161 it's a Simple belt driven pump, it's ideal even while NA, longer oil life, longer ring life, and more horsepower
@msloquet2 жыл бұрын
Have a 1964 lincoln old style system hose coming off the oil cap so I get crankcase fumes. Would this work without plugging into valve covers?
@gregadams5583 жыл бұрын
Burndown tank - See Mullet.
@tyecampbell66312 жыл бұрын
Do you get rid of the pvc valve to run a catch can?
@brianwilson56663 жыл бұрын
Hey you guys should do one on caltracs
@1982mmag2 жыл бұрын
is it true that this breather style setup generate a nasty in cabin smell specially under boost?- if yes is there a way around it, such as the exhaust scavenging setup?
@CLCIII2 жыл бұрын
Good One!
@mrgvnmcld2 жыл бұрын
Would you recommend running 1 line in (inline 6 turbo) and using an exhaust scavenger set up?
@faridgadimov59552 жыл бұрын
How about pcv valve?the one going to intake behind throttle body
@tattedsailor22553 жыл бұрын
Would yall be willing to help me out with doing a catch can setup on my 2010 Cummins?
@markhitchins71002 жыл бұрын
Would a catch can work with a holley sniper on a stock Holden 308?
@jonathanhanners60572 жыл бұрын
So you could put one on a daily drive on old vehicles and it would help it out if it was stock
@randy635011 ай бұрын
JUST A QUESTION. WHY DOES MY FRIEND HAVE SUCH A BAD SMELL WHEN VENTING THE VAPOR TO THE ATMOSPHER AS SHOWN IN THIS VIDEO⁉ PLEASE REPLY‼
@chicago16802 жыл бұрын
I can't find an answer but if your car only needs one port of the catch can, can you cap off the other port? I am working on a sxs that the catch cans are all single port use with a drain on the bottom and a filter on top there is no second port. There are some nice catch cans that I like but they only make them in dual port, I was wondering if I capped one end of the dual port if that would be ok? I don't know how the dual baffles would work. I think it wouldn't matter but I wanted to ask
@MotionRaceworksOfficial2 жыл бұрын
We also make a single port can
@peppermintnightmare47412 жыл бұрын
I like this
@nathangresell15342 жыл бұрын
Pcv is more caused by natural blowby, not necessarily so much as by the movement of the piston.
@MotionRaceworksOfficial2 жыл бұрын
It’s actually both
@nathangresell15342 жыл бұрын
@@MotionRaceworksOfficial but wouldn’t the movement of the piston cause the turbulence and air pressure changes around the rotating assembly primarily while blowby is left to cause the increase of gasses entering and therefore having to vent out of said crankcase?
@andrewbarreto32022 жыл бұрын
As far as installation goes, does it matter which line goes where? I'm curious don't wanna fuck this up.
@MotionRaceworksOfficial2 жыл бұрын
No sir can go to either side from either valve cover
@robinwendt55272 жыл бұрын
Doug shouldn't ur breathers be pointing twords the front of the motor to prevent oil coming back to them during pulls? Or is that just something that is falsehood?
@MotionRaceworksOfficial2 жыл бұрын
We have found it to be a falsehood, with proper baffling and the fittings being at the top of the valve covers it’s never posed a problem
@charlesmares4143 Жыл бұрын
Great advice. But now let’s see how it’s supposed to be routed. Preferably for a N/A LS engine. 😏
@Watchout1010 Жыл бұрын
You could sell the condensator too,pulls oil vapor out and increases milage 🥴nope..
@markcolletti5385 Жыл бұрын
Does anyone here have any pics of this brand of catch can installed on a 2017 Chrysler 300s 5.7 Hemi?
@nsuthy99s912 жыл бұрын
Need to do one on the proper way to wire a battery disconnect!! Very important and tons of wrong information out there!
@jonhill95643 жыл бұрын
Support 🇺🇲
@vincentluciano65942 жыл бұрын
I have a 454 Chevelle I want to put catch can on my engine I have the Edelbrock pro flow 4 fuel injection but my cast aluminum valve covers do not have Baffles they cost $ 750 dollars do I have to baffle them if so how they don’t have any holes in them yet I’m in the process of building my chevelle it’s just a show car with 500 hp
@PsychoBillyPerformance2 жыл бұрын
Running this setup on my boosted LS. Its currently on E85 and I get a small amount of clear liquid in the can . Is that normal?
@MotionRaceworksOfficial2 жыл бұрын
Yes that is actually moisture/condensation not blow by.
@blairski222 жыл бұрын
has there ever been a video done by dougie fresh that hasn't included him having a bruised fingernail?
@CainSample2 жыл бұрын
And you have cleetus putting catch can in front of radiator of Ruby😆 not safe
@SoftiesTruck3 жыл бұрын
Fuck the catch can talk about how to cool an LSA!!! Lol
@Hitycooking3 жыл бұрын
kzfaq.info/get/bejne/mch2draarM2rpmho.htmlu
@rickgibson66323 жыл бұрын
Do a video with your dogs.
@KCadbyRacing3 жыл бұрын
One Minute, One Canine 😎
@artinthadark45113 жыл бұрын
#DougClub
@markdavis88887 ай бұрын
Using the generic term "air" for any gases in a conversation is wrong and annoying. "Blow-by gases" would be correct for this discussion. Air: the invisible gaseous substance surrounding the earth, a mixture mainly of oxygen and nitrogen. Obviously there is also some CO2 in there.
@livewiregto12 күн бұрын
I’m amazed you figured out what he was talking about since air is such an in accurate term in this case
@BuzzysStuff3 жыл бұрын
Tell us how you smashed your finger.
@MotionRaceworksOfficial3 жыл бұрын
Honestly can’t remember. I think it was from setting the lsa on that nova
@randellgribben97724 ай бұрын
this is vented to the atmosphere, in almost any state this is not allowed
@livewiregto12 күн бұрын
Legal in all 50 states. Not sure what you mean
@randellgribben977212 күн бұрын
@@livewiregto if the can is vented to the atmosphere.. must be a sealed system.as mine is
@livewiregto12 күн бұрын
@@randellgribben9772nope, no law against this on race cars
@livewiregto10 күн бұрын
@@randellgribben9772 wrong
@randellgribben977210 күн бұрын
@@livewiregto does it not have a air filter on top of the ovs?
@ansonwill19998 ай бұрын
Talking about not getting to the point
@ldnwholesale85522 жыл бұрын
For a road car a PCV is good though not essential. Though a legality to have one,, for 50 years!! For a race car a NO NO. But fancy catch cans will not improve the car any. A couple of 3/4" hoses pushed into an empty 5 litre oil bottle will catch the oil fine. ten 1/8 holes drilled will bleed the pressure. AND they should be close to the engine,, not in the back which is plain dumb. $5 worth of hose and recycle some waste. Unless you like shiny expensive bling shit!! For road racing a catch can must be mininum of 3 litres. And all these full fumy turbo drag engines must push out quite a deal, Ideally breathe the pan into a rocker cover, crankcase fumes then go from rocker covers to catch can. I have done that for over 40 years and unless the engine was junk never ended up with more than a few ml of oil in the can, usually more water vapor. This on road race and speedway engines.