Easily the best wrap instillation tutorial on KZfaq

FYI, this video led to me purchasing your products (wrap, ties, tie tool) directly from your website to wrap aftermarket over axel pipes on a boxster. Really demystified the install, very helpful.

I'm about to buy my first bike and plan on wrapping the pipes. This is the best tutorial/example of how to do a professional job that I've found.

Amazing information really appreciated guys good work

Thanks for this upload, I'm looking forward to doing this on my motorcycle header pipes.

thanks for making this video. I was really unsure how to install this, really simplified it greatly. cheers!

Great video, many thanks

I have used this product with success. I have wet it, though. Instead of the ties (which I have purchased at a local DYI home store), I have whipped the ends with a good quality wire. I have also used water-based glue (like Elmer's) to further secure the ends. It works! Don't use petroleum-based glue. I then spray the wrap with the correct heat paint. Enjoy. (Wear a long-sleeved shirt!)

Thank you sir for the video ! Is there any benefit if we wrap the part from the exhaust manifold to the λ (Oxygen) sensor and beyond this point? or we must wrap only the exhaust manifold?

Very interesting video! How roll needed for two exhaust with 1 meters each?

Heat cycles? Any guidelines as for time / amount of heat cycles once installed before I use my bike on the road normally again

If you continue to wrap after the combiner down thru flex pipe, would you switch directions to keep keep the sewn side facing combiner as you wrap in the direction of tail pipe?

i was wondering how much i would need for a set of v6 long tube headers. also does wrapping the header lengthen the life of the header if its only painted?

I just bought some pacesetters for my Mazda b2000 which ones would you recommend.

nice!

Good idea for 07 6.0l exhaust manifold?

Hi, i have two questions, 1) should i use a high temp silicone coating with this titanium wrap? 2) wich is better? fiberglass or titanium wrap, i have a Royal Enfield Himalayan Motorcycle

will this titanium wrap soak oil in a case of an oil leek and catch fire ?

does your wrap fry o2 sensors

Nice

I used this on my 07 yfz450 and the part of the exhaust that wasnt wrapped turned cherry red. Why is that?

Question: the video discussed "counting the loops" at 1:00... Q: Is the length of one loop the circumference of the pipe to be wrapped.? The transcript clarified my question. Excellent video by the manufacturer which includes a transcript of the video's audio. !

how long will the titanium wrap last?

Whats the purpose of wrapping hour exhaust header with titanium tape?

Is it only for headers or can i wrap my downpipe with it as well?

To estimate the amount of wrap : Amt of wrap = (L/W)*C , where L= length of pipe, W=width of wrap minus the overlap (eg. 2" - 0.25"), C= circumference of pipe

How about reducing pipe-underframe rattling noise reducements? It make less sound when you warp that product?

When the hell was the flathead used?!

So no silicone spray need to complete the instal?? can one use the silicone anyway? ... also... what if a guy was to use a ceramic paint prior installing the wrap.... would that cause any adverse affects?? ... thanks....

A complete professional process there, very well structered without a doubt👌🏻👍🏻. I've installed titanium wrap on the collector section of my tuned Yamaha Zuma 70cc (Yamaha BW'S/Booster over here in Europe),it looks as nice as it does on any other bike,but is it reasonable to assume that it's making what is intended to do taking into account that it's only a scooter though being a tuned one?

The video states to wrap from collect up to the engine side. Would it hurt to start at the head and wrap down to the collector as long as the sown edge faces the collector?

question: since wrapped and/or ceramic coated headers dissipate way less heat, and impressive results are often seen where the difference can be between 200f (treated) and 800f (untreated) does the heat tend to stay more in the block, or do the exhaust gases themselves simply get more hot inside?

Hi. Had a fail on a tapered exhaust exit. Any tips on fitting and getting it to stay on odd shaped components that vary in size?

If my exhaust runs 480 degress on my bike, how much of a reduction will I see in the surface temp with the wrap?

what width and length should I get for my S2000 skunk 2 alpha header? Will this hurt my stainless header? corrosion? do you recommend a high temperature paint over the wrap?

Hi, i´m thinking about trying the Titanium wraps for first time on headers, but looking about opinions and experiences with it people talks about how this kind of wraps can damage headers because they keep moisture from condesation and it generates oxidation, is it true? Another question would be, how long does it last? do you need to renovate them? Thx in advance.

Can I do this to my Honda XR 250? And what brand and what measures of wrap do you recommend to do it?

Has anyone used this for Cold Air Intake tube? I’m reading online it’s not good to use because it keep heat inside but I read other it’s good so idk. I want to use the best so it’s either this or gold tape wrap

Do i have to worry about rust on my pipes? I got some for my motorcycle even though i don't ride in rain i do wash it.

I just got me a wrap🥶

does a High temp silicone coating need to be used with the titanium wrap?

Was the installer able to wrap that entire header with a single 2" x 50' roll?

would it be a good idea to put this on a metal air intake? it gets very hot under my hood

Someone suggested that I wet the wrap first before installing. Is that advice correct? Thank you.

Hi does this stick on tight when your exhaust pipe heats up. ? Thank you for any reply Best wishes to all

i just ordered the kit with 2 50ft rolls, I'm thinking I shouldn't have any issues wrapping a set of Hooker 2460's. They are only SBC shorty headers after all.

🎉🎉

I was told to wrap thick aluminum foil around the pipe before the titanium exhaust wrap, ButI was thinking thatthis could cause corrosion on the pipe. what do you think aboutthis method? Thanks

Not mentioned is the fact that if the overlap develops a gap and the tube is exposed, it is very possible that the exhaust will burn a hole through the steel. A friend had a Camaro running a 302 with manual trans and that happened to him. Plus, try to get all the way to the flange. Why risk it? Jere Stahl of York, PA (Stahl Total Tuned Headers), used to badmouth wrapping any header saying he had more repairs from wrap damage than for any other reason. ACP headers in Harrisburg is now making them exactly as the originals with the same methods and materials. Stahl headers were never cheap and it is a shame we lost him a few years ago. His wife had the website removed with all his instructions. My friend with the Camaro says that properly wrapped, the do work and horsepower is increased enough to make it worth the expense.

fukkk yeahhhh!!!!

How long is your wrap? My exhaust is about same size as yours

Hi im going to wrap my kooks headers (09 Mustang). Would 1 50' roll be enough? Im also considering wrapping my off road H pipe. Would an additional roll be required? Lastly, how much of a heat reduction under the hood can i expect?

Do you need to ceramic paint your headers & turbo manifolds then wrap them?

Should I be concerned that water will get behind the wrap and rust the pipe? Although, if the car is used frequently, any water that collects behind the wrap will probably be boiled away.

i was wondering what is the difference on the wraps of titanium and fiberglass. I know that with fiberglass you have to use gloves for protection and i was wondering if you have to use gloves on the titanium wraps also. I just use gloves all time working on my car. but was just wondering on the different wraps if you have to use gloves on the titanium wraps for protection?

when you wrap your exhaust. Will it get hot on the outside of the wrap (can you touch the wrap when you're driving?

My bike is going to be Bitchin with the tan wrap to match the gold frame !

Still looking for a wrap that doesn't stink when turbo engine is running.

I have bought two 50 foot rolls of DEI exhaust wrap. How can I tell if it's Fiberglass or Titanium? There is no identification on the packaging to indicate the difference.

Probably a stupid question, the header I'm going to buy is made 100% of stainless steel. Will wrapping it with the titanium wrap be harmful or helpful on the steel? Just dont want any degradation of my header.... and does this also help with hp gains? Is it strong enough for long term usage?

Does this itch like fiber glass wraps?

what's the best brand of exhaust wraps? i see divergent prices form 15 to 70 dollars why?

1:45 confusion... you said more material to the outside (while the dude correctly show the inside) ;-)

Definitely need gloves... My hands are very itchy now... Wrap worked great though.

Any spray necessary for this type of wrap?

can this wrap cause damage to bear skin over repeated contact? I'm considering using this product for an AR build which will only reach a temp of 120 degrees F

Would this product work well to wrap my intake piping to keep heat out?

thank-you u can drink a few beers or any drinks on me anytime u are on Broadway San Francisco impala club ask for John 👏👏🍻🍻

Dare I ask, is wrapping the exhaust manifold whilst ON the care possible/beneficial?

how long wraps I need for camaro ss 2010 V8 ?

So you don’t tie the beginning? Only the end?

AAH.... Olds-mo-bubble. You can wring the wrap by hand as you advance truns to ensure keeping a tight grip on the pipe.

I have exhaust wrap on my Quad and after a couple of rides it is all White and not Black anymore. Why? I dont remember the brand.

I got some of your wrap but it unravels immediately after cutting--how do I prevent that?

How long can I expect the wrap to last?

does the wrap melt

eye protection? why,are those fibers dangerous,something you're not telling us?

Ecxelente vid, don't know why 29 people did not like it ? F***** heater...

I have heard a myth of Exhaust Wrap, it can reduce the car interior exhaust drone, is that true?

why do you need gloves?

Whats the point of wrapping? May sound like a dumb question but with or without stuff wrapped in my car i am not going to touch hot car parts. Lol

Exhaust Wrap - always a bad idea...

Heat wrap destroys YOUR HEADERS.

Yeah those ties are garbage. What a waste of $20. Just use worm gear clamps. So much easier. Look much better than the chicken wire that snaps when tightening with the tool.