Motorized bike Pull start
Рет қаралды 39,043
3 жыл бұрынin this video I install a pull start, witch was kinda straight forward. but for the people who needed a tutorial. here ya go. this thing literally took 10 min to install. its the easiest thing that I've had to install on this bike.
SUBSCRIBE ➡️➡️ / @barriosbuilds7688
If your in the mood to check out some of my other builds/projects click here!
street legal bike???
• Attempting to Make a M...
Off roading a motorized bike!
• How Much can a Motoriz...
Speedometer
• Old School Style Bike ...
Once again thank you for watching this video, hope you have a good one!!
@kingpc55 3 күн бұрын
I have the same bike with the same motor
@billstrube3425 3 жыл бұрын
I have installed a few of these on customers bikes. Don't bother to use them, they are junk, and will only break after a few pulls. I no longer use them on any of my customers bikes.
@HighMileageOffroad 3 жыл бұрын
Yup get a Grubee with an electric start capable crank!
@christianbelcourt279 2 жыл бұрын
I've had mine on for over a year, hundreds of rough pulls and no problems.
@ethand4784 Жыл бұрын
is it the rope or the mechanism? I would gladly replace the rope if that's the issue
@andrewmasten1235 Жыл бұрын
@@ethand4784 the tabs around the magnet broke on mine and if you dont notice and keep riding, the whole compart looks like it was in a war zone
@derpydog1008 8 ай бұрын
I almost bought a pull start kit. Wow thanks for the heads up dodged a bullet.
@keeganhache6667 3 жыл бұрын
I see you with the new carb got one of those and they work great
@omargdottin 3 жыл бұрын
I just order one of those too, replace the oem that came with the engine
@HighMileageOffroad 3 жыл бұрын
Unfortunately those carbs are trash compared to the genuine mukini vm18 carbs trust me get ya one and some jets from www.treatland.com and thank me later! I'm running 52mph with mine along with a g2 reedvalve and windowed piston she pulls and screams without a Jack shaft kit.
@vincent10717 2 жыл бұрын
I hate them, mine did not work out of the box. I like their design more than the older ones, but I needed to purchase an older one to get my engine to run right.
@Mnaytorri 2 жыл бұрын
i have the same bike, can u pls make a video on converting the granite peak to disk breaks? it would be greatly appreciated
@barriosbuilds7688 2 жыл бұрын
I did, but it didn’t turn out well. You just need a bracket and a basic disc break kit. I might try it with my other bike because I don’t think those rims were made for the standard U break setup.
@edog4333 Жыл бұрын
I need this for mine so cold to start it
@lorriecarrel9962 2 жыл бұрын
Cool
@kleptoklepto2560 8 ай бұрын
hey my bruvva! ive got 1 of them "100cc tdr motors" is there a pull start 4 them? & if so could u please let me know where u bought it & the exact name of it! cheers bruvva
@zachdillon275 2 жыл бұрын
Where did you get the shift kit? Every time I try to start my new 100cc kit the old chain would break as I pop the clutch as the motor tries to start so I got a better chain and that one jams up because it tries to pop off the drive sprocket when trying to start it. No matter what I do with changing alignment it still does the same thing so I hope that would help me.
@zachdillon275 2 жыл бұрын
@@LugiThePainDrinker what part is the flower nut?
@karltaylor4847 Жыл бұрын
Slowly release the clutch as u peddle I have the same problem but get a bit of speed up peddling
@erdenetugs2958 2 жыл бұрын
hello guy.What is Motor sprocket otherside partition tool name ?
@americanpatriot212 2 жыл бұрын
I was wondering if I could pull off a pull start from a broken weedeater or something and try to use
@barriosbuilds7688 2 жыл бұрын
Same here, but even a weed eater has a better pull start design than these.
@felipeaguirre6162 9 ай бұрын
En donde se pude compra me podes decir si no es molesto es claro
@JesusRamirez-jl9be 2 жыл бұрын
Where did you get those crank arms? That's what I need, my crank arms is always bumping into my exhaust pipe 🤔
@barriosbuilds7688 2 жыл бұрын
They came with the jackshaft kit, but I believe it’s just the standard wide crank set.
@itsthebart9050 2 жыл бұрын
you can heat the exhaust pipe and bend it out of the way
@karltaylor4847 Жыл бұрын
I have one just struggling with the original carb any ideas guys please ??
@Fred_Zepplin 2 жыл бұрын
How long did Your's last?... Every One I ever bought broke in the first week.. I've taken the old cases and made Better components and upgraded IT..diy style.. Now, If I'm Building for Someone else, & They want The Pull Cord.. I'll Take Off The Crappy Catch Wings & replace Them From Jump ... For My Off Road Builds.. I Mix some 2 Part Epoxy and Lightly PAINT It on the various components and let it dry before re-assembling.. Just too try & re-enforce The CHINA Quality of The Parts.. BUT, Only A VERY Light Coating.. Seems To Work Well?.
@barriosbuilds7688 2 жыл бұрын
3 pulls
@Fred_Zepplin 2 жыл бұрын
@@barriosbuilds7688 .. Yeah, Ya pretty much need to upgrade them right out of the box.. If Ya still have the broken ones.. try and fabricate the broken parts.. You can do It With basic tools.. jig saw..angle grinder and a good hand file, As well as maybe drilling out the rivets and use some small stainless steel nuts/bolts.. They will work Pretty good after Modding Them.. But, Cheap Junk Out of The Box.. Thanks For Sharing Bro... Keep On Rippin' !!!
@barriosbuilds7688 2 жыл бұрын
Too much work for something that should work right out of the box… went back to stock.
@Fred_Zepplin 2 жыл бұрын
@@barriosbuilds7688 .. Yeah, Most just take it off and put the original cover back on.. A Pull Cord is handy to not pedal.. But, If Your bike is set up well, 3 or 4 "Pedals" and You're off to The Races Anyway.. I Liked The Pull Cord on Chopper Builds.. They're Crap to pedal, A Pull Cord is nicer imo. .. A Mountain Bike.. Pull Cords are not really needed.. The Choppers were made for Engines.. Most were crap To Pedal..lol. True Tho! .... Stay Awesome Brother !!!
@JadedNegotiation Жыл бұрын
@@Fred_Zepplin yep can agree the stingray shoppers are shit to pedal. my kill switch falls apart then gotta pedal 2 miles home
@warrenmartin7039 Жыл бұрын
Do any of you guys know what site that I go to to order the rear drive sprocket for the mag rims there's two one on each side
@jccornerstone 11 ай бұрын
Did you ever figure this out having same issue
@RightLane393 Жыл бұрын
do have hold the clucth when pull start ? how does it work. My clucth gear box is damage inside this metho can it sovle the problems ?
@YoMotab 3 ай бұрын
yeah you have to hold in the clutch or you're gonna have a very hard time pull starting it
@jayvlog9841 2 жыл бұрын
I like that start puller
@barriosbuilds7688 2 жыл бұрын
Don’t not worth it
@elsasilva4401 2 жыл бұрын
With a normal pedal will the pedal rotate
@catsnponds5959 Жыл бұрын
No
@dash_amazingcool2314 Жыл бұрын
What pedal can I get so I can pedal without it hitting the push starter
@catsnponds5959 Жыл бұрын
@@dash_amazingcool2314 extend your crank arms
@user-pi8vt7ut3n 2 жыл бұрын
... почему не поставил гроверную шайбу под гайку,- со временем открутиться от вибрации?!!
@keithaustin2917 3 жыл бұрын
I hope you gonna put the wires away from the exhaust pipe
@jcodaniel5678 2 жыл бұрын
I’ve always just pedddled and mine to start it up
@Westhelockpicker 2 жыл бұрын
do you have to have a pull start if you have the shift kit
@barriosbuilds7688 2 жыл бұрын
Yes
@Westhelockpicker 2 жыл бұрын
@@barriosbuilds7688 if there was a way around that I would be getting it
@barriosbuilds7688 2 жыл бұрын
If there was a way around it, I would be buying another one!!
@matter4789 3 жыл бұрын
First!
@edups1 2 жыл бұрын
I'm about to make it so my can be started my a drill
@ogjacob 3 жыл бұрын
Does that mean you can't use the spark plug that much anymore
@ogjacob 2 жыл бұрын
😐
@ogjacob 2 жыл бұрын
😶
@napsum9255 2 жыл бұрын
Aww, no it still need the spark plug.
@ogjacob 2 жыл бұрын
@@napsum9255 thanks 😊
@TacticalPhoenixYT Жыл бұрын
Bro what💀
@leavehuh7744 Жыл бұрын
is it easy to cold start it?
@barriosbuilds7688 Жыл бұрын
Yes! If it doesn’t break.
@BuildBreakFix 2 жыл бұрын
Lol you all know how that pull start ends up shortly after!
@barriosbuilds7688 2 жыл бұрын
Broken
@glennkelly885 Жыл бұрын
Ok u w to remove the pedal start set up just to add the pull start
@barriosbuilds7688 Жыл бұрын
I had to use the wide cranks… but it wouldn’t let you pedal start anyways.
@cellgamingg1329 Жыл бұрын
How much did those nuts cost
@JamesPiccone 3 жыл бұрын
The only problem with a pull start is it will Waller out your keyway slot for your magnet & cause f***** up timing issues. That bolt and keyway slot was only designed to hold the magnet in place, not the torque required to turn over your motor. It will work but over time you will produce more slop in the keyway slot causing timing issues.
@gewizz2 3 жыл бұрын
id much rather have bump start than that pull start
@cnoshoes7049 Жыл бұрын
Ya exhaust will snap off unsecured
@cnoshoes7049 Жыл бұрын
Ya chain spring clips wrong way round m8 ! X
@heavystarch100 2 жыл бұрын
The pull start...meh, but that watch band is 🔥🔥🔥🔥🔥🔥👍🏾
@glennkelly885 Жыл бұрын
My motor. Is a 80cc motor for my bike cycle
@jerryb1234 3 жыл бұрын
Why are you making such a big deal out of it being painted or not?, spray-paint is cheap, lol, was the jack-shaft worth the time and money or not?
@barriosbuilds7688 3 жыл бұрын
Yeah I’ll paint it, Jackshaft worth the time no but for the money. It’s okay, just a lot of finicky parts to deal with.
@HighMileageOffroad 3 жыл бұрын
Dont get a jackshaft kit take it from me I've been working on these for 2 years and my single speed 66cc is currently hitting 52mph with ease! Wanna make your run the same message me and I'd be glad to help!
@andrewmasten1235 Жыл бұрын
@@HighMileageOffroad I had my 80cc anbull at 35 and switched to a 36 tooth sprocket, tuned the carb a little rich with no air filter and only got to 43mph
@andrewmasten1235 Жыл бұрын
That was a month after I put the motor on and iv been rebuilding and trying to figure out how to do my port timing since.
@HighMileageOffroad 3 жыл бұрын
If you want to know how to make your engine do 50+ comment and I'll help ya I've been building these engines for 2 years and know what I'm doing! I know what does and doesnt work on these engines and wiold be glad to help ya get your speed fix!
@tonypagan8852 3 жыл бұрын
Im just starting out on this motorized bikes and id like to know hiw to make them faster
@HighMileageOffroad 3 жыл бұрын
@@tonypagan8852 do you have Facebook messenger?
@codenamethecleaner7519 3 жыл бұрын
I’d like to know! Please. Tailored Detailing on Facebook
@jcodaniel5678 2 жыл бұрын
I am interested. I don’t have a Facebook but I do have messenger
@sevensavage7905 2 ай бұрын
very late comment but you would you be eilling to help me as well
@GerardoCSpike 2 жыл бұрын
Sooo... did you have any timing issues???
@barriosbuilds7688 2 жыл бұрын
Yes I did, actually I think this is the reason the motor stopped running. It plays with the timing.
@GHOSTGAMES724 3 ай бұрын
how does your bike not leak un burned gas and oil all over it
@barriosbuilds7688 3 ай бұрын
I mean I had some leaks but make sure your head gasket and base gasket aren’t torn. Because that can cause oil to leak everywhere.
@reneydiaz3162 3 жыл бұрын
What part number is this
@barriosbuilds7688 3 жыл бұрын
Didn’t know there was a part number. Just bought it off Amazon.
@erdenetugs2958 2 жыл бұрын
@@barriosbuilds7688 can u take a link
@tb33man82 2 жыл бұрын
I'd pin those wires away from your exhaust
@LorenzMiami Жыл бұрын
so u don't use the pedals anymore......mmmm
@barriosbuilds7688 Жыл бұрын
Nope…
@napsum9255 2 жыл бұрын
That's a Trek
@wrench Жыл бұрын
used an m18 drill to drill start my motor and i completely stripped the magneto nut lol
@dragos_daniel_.1064 Жыл бұрын
top speed ???
@barriosbuilds7688 Жыл бұрын
This bike only went about 25mph… but after all the upgrades I did, now tops out at 37mph.
@dragos_daniel_.1064 Жыл бұрын
Verry good speed
@leonardarola 2 жыл бұрын
Centrifugal clutch? Pull start? Done that. No, thank you.
@CarloBerroa Жыл бұрын
Spray it black
@yeetskeet4638 2 жыл бұрын
The pull start I had exploded after 1 day
@barriosbuilds7688 2 жыл бұрын
Happened to me 3 times… finally gave up on them.
@eddydaMotorizada-Rj Жыл бұрын
Você falou e falou e não vi nada de interessante. ..
@jlovee2211 8 ай бұрын
theres no point of having a pull start, u can’t ride it from a complete stop, u gotta start pedaling regardless to accelerate
@barriosbuilds7688 8 ай бұрын
The pull start was for the jack shaft kit, witch both are a complete waste of money. You can’t start a bike with a jack shaft kit by pedaling. But after replacing 2 pull starts, I threw away the whole jack shaft project. The straight chain drive is way more reliable.
@user-zx1rt8ed5z Ай бұрын
Yea you can you just don’t know how to
@user-zx1rt8ed5z Ай бұрын
Yea you can you just don’t know how to
Barrios Builds
Рет қаралды 99 М.
Hughes Motorized
Рет қаралды 89 М.