Motorized Bike ways to Increase port duration and Working on the Cylinder

Рет қаралды 6,912

9 ай бұрын

Welp we made a spacer for more transfer timing and raised the exhaust port and widen it to 32mm not the conventional shape we tried something different this time. The piston window turned out pretty good that little gap can be fixed so easy not worried about it

Пікірлер: 46

@flakey7832 25 күн бұрын

Usually younger "tuners" are atrocious to watch work on engines. This is amazing, knowledgeable, well explained video, very scientific methods. Keep it up

@tiger7777 9 ай бұрын

Thanks again Keegan. Looking forward to seeing how it works out for you.

@boydjensen3161 9 ай бұрын

Impressive Keegan, keep 'em coming. Excellent work!

@keeganhache6667 9 ай бұрын

Thanks brother

@brycehomola7078 2 ай бұрын

Dude you’re super talented and knowledgeable keep it up your going somewhere.

@Ragz10 9 ай бұрын

I usually wear safety glasses mask and gloves while doing most works thay have thinga flying around tbh. Good work

@grendelsgarage9723 9 ай бұрын

Great video!! Make me want to finaly do some port work.

@keeganhache6667 9 ай бұрын

It’s worth it man

@Op1zilla 9 ай бұрын

Another TIP is small Boost port, and if you do a third transfer you can skirt the piston instead of cutting a hole in the piston, Ive had Great results , just something else to try on the next cylinder 👽👍🏻

@justanothermotorizedbikech5138 5 ай бұрын

Can you run piston port with a boost port?

@keeganhache6667 5 ай бұрын

@@justanothermotorizedbikech5138yes you can

@KevinTodd 9 ай бұрын

nice👀

@keeganhache6667 9 ай бұрын

Thanks Kevin

@R_Kyllonen 9 ай бұрын

Keep em’ coming

@yomontOME 10 күн бұрын

Thanks for the video bro it helps a lot

@justanothermotorizedbikech5138 5 ай бұрын

Bro that mushroom port really works👌🏼

@michaelbrinks8089 9 ай бұрын

About the only main thing I seen in the 2 stroke tuners handbook of importance besides squish, was rounding the edges on ports with a file after porting 🆚 leaving everything having a sharp edge....So its smoother flowing, like on the piston window, u can round the edges of the window to direct flow into it. Same with ports, round ex port roof & sides. Many round the pistion skirt lip on intake side & round the intake floor so flow is going over a smooth curve & directed downward unti case instead of over a sharp edge. Same with porting the case they'll round down the sharp endge in the case where it's flowing up into the transfer ports. There's a few good moped case porting videos .

@keeganhache6667 9 ай бұрын

Yup it’s always good to sand down edges after porting the cylinder

@2strokecarbtuningportingin187 9 ай бұрын

Flow case porting is bum information your compressing gasses not liquid. If you have a step a impedance in the intake port yea that's helpful. Or a impedance in exhaust exit sure. Butt a step in a out flow say like tranfers to cyl your doing nothing but lowering crank case pressure wasting time and effort. You won't find a single video showing power gains factual power gains on case porting with the exception of a case Reed motor with a inflow impedance. Just stating proven facts

@noahriedel801 6 ай бұрын

Hey man....I just wanted to say you're killing it at your age with the knowledge you have. I'm very impressed. I have to ask you how did you learn all this at such a young age ???

@michaelbrinks8089 9 ай бұрын

I've never taken the fiberglass wrap off the magneto coil to see how well it's made/coated.....But had some clear 2 part epoxy laying around, so I coated over the wrap that's zip tied on & everywhere on the coil where moisture could get in. Made sure to coat the wire solder joints good, so they wouldn't corrode or break from vibration. Used a whole 25 cents worth of H ⚓ F epoxy. So it wasn't a waste of $$$ I dunno how much it helped but it didn't hurt anything. I leave my bike outdoors 4 seasons under a tarp & the coil has been working since 2020. Not sure the average coil life span but have seen several people needing to replace them so....🤷‍♂️

@keeganhache6667 9 ай бұрын

Wow man that’s actually great information might try it I was only going to do it on the backside to help it have metal to metal contact in the case itself

@michaelbrinks8089 9 ай бұрын

@@keeganhache6667 Have you ever had any coils go bad after like 1 year ? I'm not sure the exact number but seen several videos & people on forums mentioning that their coil went bad after only 6 months or a yr. Then mention upgrading from the 3 wire to a 2 wire, etc...Saying the 3 wire is junk & that's why it only lasted 6 mos... I got the 3 wire coil & it's 3 yrs old so.....I rarely use my kill button, I heard that makes em go bad but dunno how much truth there is to it. Supposedly the kill switch shorts it out to stop the spark & makes heat but the coil is already hot from being mounted to the engine. 🤷‍♂️

@michaelbrinks8089 9 ай бұрын

@@keeganhache6667 OH yeah had I been thinking I would have looked over the ignition coil/cdi box, to see how well it was sealed up & expoxy coat it, if it didn't look well sealed.

@Bobs-yer-uncle 9 ай бұрын

Keep em coming man i think im starting to understand this stuff 😂and im pretty sure i windowed my piston too high 😢

@keeganhache6667 9 ай бұрын

Good thing is pistons are cheap! Remember there is a high hole and low hole styles

@baby-sharkgto4902 9 ай бұрын

Hey I like your videos, I just started watching. Can you take the cylinder to a machine shop and get the top shaved? At TDC the piston is waaaAAAy too low in the bore. At the same time I do not know what you run for fuel so keep compression in mind when doing so. Also if you end up in a situation where you have “too much” compression there is a product called VP Octanium and it works great and can be bought at Walmart and auto parts stores for 22 bucks, or even Summit Racing will send it to you, but do not use any other store bought octane booster as it does not work. Keep experimenting and keep learning!

@macmotorizedbike3834 5 ай бұрын

Good job

@Ragz10 9 ай бұрын

That's the style of exhaust port i run w 70% bore.

@2strokecarbtuningportingin187 9 ай бұрын

Fix that deck hight. That's not a Aprilia style port it's a Amos style port. Just saying. 😊

@keeganhache6667 9 ай бұрын

Yessir how’ve you been? Been watching a crap ton of your videos man they really come in handy when ever somebody said your info is wrong I show them the 60 mph video of you flying lol

@2strokecarbtuningportingin187 9 ай бұрын

@@keeganhache6667 only doing NHRA prostock motorcycle engines. Kinda tired of them nowadays. Good job on making vids. Tip on window making you can drill your 4 corners and have perfect radius,s. Filter out the bum information in the comments. All that directional case port matching and angled comments are comical. Especially vids saying crank rotation. Case flow port matching. Super simple point people miss your compressing gasses not liquid. Keep doing exactly what your doing you'll find out first hand who's information is factual. I don't write great so don't take my responses wrong. Basically don't fall for bum information. I have factual real world tested litterly everything. Keep up the good work

@keeganhache6667 9 ай бұрын

Great tip on the window definitely will give it a shot next time around I’ve always used this method and the chinadolls keep up with my Minnerelli so it’s saying something I can link your channel in the description if y’a don’t mind take care brother

@2strokecarbtuningportingin187 9 ай бұрын

@@keeganhache6667 one more simple tip. Mark your tranfer opening line around to the exhaust port. If you keep most of your changes above the tranfer opening in your exhaust port you have less ring bulg. Hence the mushroom shape. Never have I snagged a ring hundreds of cyls ran

@2strokecarbtuningportingin187 9 ай бұрын

@@keeganhache6667 it's definitely cool. Big credit to you your applying your learned skills with YOUR HANDS. ANYONE can bolt on a pre maid cyl and act like they actually improved something. BUT YOU CAN TAKE 💯 % CREDIT FOR HOW YOUR ENGINE PERFORMS. SIMPLY YOU TOOK A 🍋 AND MADE LEMONADE. you made something out of nothing. Do minarelli and other pre made cyls run good answers ehhh yea. But where is the lesson in that. Keep up the good work.

@user-jo8eq9cc7w 9 ай бұрын

A rough intake port better for atomizing the gas? Now that is the first time i have heard of that? Until learning about 2 strokes, i have always thought polishing the ports for smoother air flow was the way to go??

@keeganhache6667 9 ай бұрын

Nope only do that in the Exhaust this is not a fuel injected car engine the intake port needs to be textured

@passenger6735 9 ай бұрын

Surely for the low velocity gases you need a larger port to 'coax' the gases out, similar to valve size on a four stroke. With that in mind is your port upside down? I am not an engine tuner by the way.

@keeganhache6667 9 ай бұрын

No see the issue on a 2 stroke motor is if there’s to much port area at low rpm’s the motor can’t flow the gases properly it’s like putting a 4inch exhaust on a Honda civic it can’t use the velocity you need a smaller port at low rpm

@passenger6735 9 ай бұрын

@@keeganhache6667 Thanks for clearing that up.

@janeali1174 4 ай бұрын

sir i need a help from you i have 2 stroke cylinder i want to increase its rpm it has 3 ports in which one exhaust port i also very tried but couldn't increase please can you tell me How can I increase the RPM power from the port of this cylinder? Please help me in this task sir