Рет қаралды 1,860
Tinkering, modding, how to upgrade the Nakto F2 for very little
Check out the Nakto F2 here: shrsl.com/47gxx
If you want to buy it, use coupon code: TRUTHER60 to save $60.
stuff in this video
child seat amzn.to/44ZuZ3R
light amzn.to/45Z9wJy
bag: amzn.to/3ZnOpOu
menu from paselec GS9
P01:Backlight brightness: the darkest level 1, the brightest level 3;
P02: mileage unit: 0: KM; 1: MILE;
P03: Voltage level: 24V, 36V, 48V, 60V;
P04: Dormancy time: 0, not dormancy; Other numbers are dormancy times, range: 1-60; Unit minutes;
P05: PAS number selection: 0, 3 file mode: 1,5 gear mode:
P06: Wheel setting: unit, inch;
4
wheel diameter value: 5.0 ~ 50 Precision: 0.1 inch
This parameter is related to the meter display speed and needs to be entered correctly; P07: Speed gauge magnetic steel number: range: 1-100;
This parameter is related to the meter display speed and needs to be entered correctly;
If it is an ordinary hub motor, the number of magnetic steel is input directly;
If it is a high-speed motor, it is also necessary to calculate the deceleration ratio, and the input data = the number of magnetic steel × deceleration ratio;
For example: number of motor magnets 20, deceleration ratio 4.3: input data is: 86 = 20 × 4.3
P08: Speed limit setting: Agreement No. 2 range 0-100km / H, 100 means no speed limit;
The input data here represents the maximum operating speed of the vehicle: for example, input 25, indicating that the maximum operating speed of the vehicle will not exceed 25km/h; The drive speed is maintained at the set value,
Error: ± 1km/h; (The speed limit for power and turning is equal)
Note: The value here is based on kilometers. When the unit setting is converted from kilometers to miles, the speed value of the display interface automatically converts to the correct mile value, but the speed limit value data set at this menu under the mile interface is not converted. Is inconsistent with the actual speed limit of the mile speed;
P09: zero start, non-zero start setting: 0: zero start; 1: Non-zero start;(valid for protocol 2 only)
P10: The drive mode is setting: 0: Power Drive(how much power is output is determined by the power file bit, and the switch is invalid at this time).(valid for protocol 2 only)
1: Electric drive(by turning the handle drive, the power file bit is invalid at this time).
2: Power Driven and Electric Driven Coexistence
P11: Help sensitivity setting:range: 1-24;(valid for protocol 2 only)
P12: Help start intensity setting:range: 1-5;(valid for protocol 2 only)
P13: Power Magnetic Steel Disk Type Setting: 5, 8, 12 Magnetic Steel Types
P14: Controller limit value setting:range: 1-20A
P15: Controller undervoltage
P16: ODO zero setting: length press key 5 seconds ODO zero
P17 :Automatic cruise optional:0: No enabling cruising, 1: enabling cruising; (valid for protocol 2 only);(valid for protocol 2 only)
P18: Display speed ratio adjustment: range: 50 % ~ 150 %,
P19:Zero PAS selection: 0: 0 file, 1: does not include 0 file
P20 :0:2 Protocol 1:5 S Protocol 2: Standby 3: Standby
00:00 Accessories
01:01 Battery Issues
04:27 Light Addition
05:28 Speed hack
08:08 Amp it up