Como lo reiniciaste ?

Did it works with your RHB?

Curious if anyone has got the steering wheel controls to work on non can bus vehicle with RBZ or RHB radios

Hola qué tal, oye una pregunta en tu estéreo donde se conectan los arnes tienen dos hileras de pines? Es decir donde están las patitas más gruesas esa es una hilera de pines y arriba tiene otra hilera de 10 pines?

@@fidomontano2204 es el de arriba

Hola disculpa cómo hiciste para que funcionara?

@@LuisLopez-se4dq lo iso funcionar? Ami no me prendio ni arriba ni abajo

De donde conectaste el auxiliar? Para saber si el arness que de mi carro no tiene ese cable

there are 2 different canbus speeds for these radios a lowspeed bus or a highspeed bus, they cannot be interchanged and you cannot make them work without using something like a mygig lockpick. do not try to power the radio like is shown in this video, it will not work and could permanently damage the radio... unless you have a highspeed rbz mygig, I would not risk damaging the system.

the code is 0000

Yes I added a wire to the harness

I don’t know. I am not a professional…. I just got lucky and stumbled on this solution after a lot of frustration lol…

The small square plug in the middle was for the steering wheel controls for volume, and radio tuning

I am not sure about the video out on these models “. The majority of the ones I see have the av plugs attached to the radio

Me too. Wont work in my 2011 jku even tho the cables match up.. radio is from a 2010 grand Cherokee

I think it does have a video input in back of unit

I’m sorry for late response I haven’t checked my channel in a few months. . What I did was I ordered the matching wire harness clips on Amazon that just clip in the appropriate slots in the harness

Yo también tenia ese problema

Disculpa amigo que se tiene que hacer para que vuelva a funcionar, tengo una cheroke y ya no quiso encender, como hiciste para que funcionara de nuevo?

Which what are you asking?

@@keithonwright I found it but it asks for a code 😢

By the way the default security code is 0000

You are right because I am having that problem

@@keithonwright I have been researching this non stop since my first comment, I have bought every version of mygig radio that mopar used. it has been known that the mygigs got the time/clock info from the wcm/cnn via the canbus system. there is an updated firmware for the rer/ren mygigs that lets you manually input the time and it will not double check via canbus, so the time will display as normal. but since this firmware is only for the rer/ren, and those models will not power up without a canbus signal, it doesn't help us here with the rbz. but the rbz can be powered up like you have shown and everything except the clock will work just fine.

Jacob Aikey thank you for the info. It is annoying that my clock won’t set. But if you find any info on what to do to fix that, that would be awesome!!

@@keithonwright do you know if your radio is a high speed or low speed canbus unit? and what car do you have it in?

@@keithonwright ok I just re watched your video, if you still have the 07 aspen, that is a low speed canbus vehicle and would need a low speed rbz radio to function 100% with the clock working. so I am guessing that the car that the radio came out of was a high speed canbus car?

Dod you ever figure out what works for the REN?

there are 2 different canbus speeds for these radios a lowspeed bus or a highspeed bus, they cannot be interchanged and you cannot make them work without using something like a mygig lockpick. do not try to power the radio like is shown in this video, it will not work and could permanently damage the radio... unless you have a highspeed rbz mygig, I would not risk damaging the system.

Hola..a cuales pines van los 12v??