Absolutely the best video on rigging on KZfaq. Thx for all the details. Great job!! Be safe.

I think the big take away for me is to tie that stopper knot at the block so you don’t have to fight the weight of the rope when you tie the piece

Always enjoy your videos have about 2 yrs in the spikes and still have so much to learn. Thanks for all the knowledge

Perfect training video. I think you are very well trained and you do a great job explaining all the steps. Im continuously impressed by your content, probably the most proper well described arborist site Ive found on YT.

I really like this style of training video, well done! So often things happen so fast and it’s good when you’re stopping it and explaining what’s happening. The one thing I was going to say was that when Connor was making the first back cut on the first piece, I think the reason he does. The powerhead down is the reason I do too and that is because it is easier to line up your back cut with your face cut accurately that way. I switch just like he did to power head up once I’ve gotten in a few inches and set my direction of cut where I want it to go

Loving the detailed analyses of various techniques. Definitely fills a void.

Excellent tips, love the way you talked that through.

Good tips....the only thing I like to do is keep the distance between my rigging block and half hitch as small as possible to reduce the travel distance when the piece comes off, thus decreasing shock load on the rigging system.

Thank you Dan!!! There are so many small details in this video that have a huge impact on the job. A lot of the things mentioned are not pointed out in other people's videos. Ex: the power zone, running the bar forward, and placement of the rigging block/portawrap to prevent rope damage. I wish I could've seen your videos earlier in my career. Please keep making more videos like this. Thanks again man!

I loving using the top of the bar. I don't use it in big hardwood. Shooting all the sawdust away from the climber is nice at times. But I agree it's not the best practice.

Great video! The only improvement I could suggest would be adding tags for each major point so people can find them when they revisit the video.

Great spar/neg rigging video.

Thanks for posting this video. Lots of great tips. 👍🏼 Climb high. Be safe.

Very good detail. Thank you.

Another excellent video Dan. I started watching the first one, and then it was pulled from view. I will watch this one today. Thank you, Jim H. Portland, Oregon.

Hi Dan Thanks for posting another excellent video!

Good job explaining the rope and lanyard positioning. I started out doing it wrong with it below but was taught to do it the right way later on. I've never heard it explained so well as to why you should have it over the rigging. I've done a lot of negative rigging but I still watch these videos.

Superb educational video, thanks.

I appreciate the insight and consideration in negative rigging. It gave me some things to think about to improve my system. I'm curious why not use a Humboldt cut when blocking them down? I wondered if that style of cut would of helped with the third short block from just resting once it was cut. Anyways thanks for the video.

Great instructional video as always

Great video and very complete. Lots of useful tips

I like to keep at least one of my tie in's below the rigging sling just in case there's a hard catch and you end up taking a ride. No chance of the rope popping up off the top of the spar. Great tips Dan! We have a training coming up next week and I'm going to practice some of these to keep working on getting more efficient. I think overall I tend to not cut deep enough and also leave too much hinge making it all harder on myself. One question, what are your thoughts on tying the log on higher up? I've seen other demos saying that it does not make a difference in drop distance. However that's not how I learned it starting out and I'm not convinced without seeing some live full size demo's. Great video and thank you for all the tips!

Good videos man thanks

Excellent video Dan

These tips are useful. I enjoy this video. Thanks for your sharing.

Awesome video I really appreciate it iv production felled and climbed and bombed things out and iv done a little rigging doing this full time now learning about rigging on the go very well explained thanks

Thanks for the vid Dan! 🙃

Very helpful. Thanks for sharing. 👍

i like the to use the top of the bar when making the back cut as it pushes me backwards ans braces me more in to my lanyard

Thank you friend. You are make the world better with your work. cheers

Every time I’ve ever had to do this the slam of the pole hitting the trunk always freaked me out. I’ve had 2 slip out of the rig and thankfully didn’t damage anything but is incredibly scary in the moment.

Wow thank you for this

Great video! Thank you!!!

Please explain to me why you make the face notch cut with a flat bottom cut. It seems to me that it makes the log kick out way more than it needs to? Wouldn't an angle cut on the bottom of the face cut stop the log being kicked out so then it would just fall straight down the trunk? Less impact, less jarring and earlier tension on the rope for a smother ride? Thanks

Complimenti per il super video

Great video again, thanks! Just wondering if you have some good suggestions for techniques to help manage the situation when the trunk starts getting thick (say ~30" diameter), so only shorter pieces of trunk can be rigged then.. I have snapped an eye spice before on a 1" thick rope on the pulley block from overloading it! (Sometimes it's not possible to let it run far first, which would reduce the shock load, eg over a house etc) But cutting shorter pieces then has more chance of the rope coming off them, even when rope notches are cut in... Any ideas to help?!

Great very interesting points👍

With the rubbing bowline “newish arborist” you said stopper knot to prevent it coming out. Is that where the Yosemite bowline can be used to either or ? Or would you say it’s just easier for the stopper knot ? Thanks.

Dan like your videos big fan of your page have learned alot from your videos

I learned some good stuff here--thanks! Examples: don't place porta--wrap directly under the rigging block, also the cow hitch I'm a new climber.

Good video!!

I think I saw this one last week, and it was excellent, too. Some day, a discussion of options for descending the spar would be helpful. Is the most efficient strategy to simply spike down with only the lanyard, or do you leave a long end on the climbing line to allow you to flip it off the top after you're at the next station? For the last length, do you switch to a double rope technique with a friction saver, to allow you to retrieve the climbing rope before dropping the final piece?

Side cuts are very important. I've done this after the base cut & b4 the back cut & have had great success. I like the negative rigging with a port-a-wrap @ the bottom. I've had many when dealing with forked branches that I tie another rigging line @ the fork then I make a few extra swipes with my Japanese hand saw to get the desired hinge. Then I go to the ground & hook that rigging line to my Maasdam rope puller. The bridge snaps & the forked branch that's about 15 feet long comes down right where I need it to be. I'm working on dead trees & for 3 years I haven't hit any fencelines that r in jeopardy. Trying to rush things just causes more damage & can lead to alot of risk & extra work.

Great video, not sure what your thoughts are on this. Something I've done is facecut first, THEN setup the rigging block/rings and tie on the piece at the same time. Thoughts on this are, less chance/no chance to cut the rigging sling and then being able to set the sling as close to the facecut as practical, still maintaining a hands width from the cut for lanyard. (Lifeline tie in point below rigging sling). Also turning the saw off between facecut/tying on and then communicating the piece to be rigged and then making the back cut, can help for no helmet communications and higher distances.

Awesome stuff bud love these videos great for people to learn from. I typically use blocks with a cow hitch I'm not a fan of rings for negative rigging but that's what I prefer. I think the Porta wrap on the right side would of helped better less rubbing on the trunk less likely to get hit by the piece. Negative rigging beats up on gear no matter what we do. Not bashing how people do anything but the space between the block and marl is a little much for how I would have done it but I also don't like how some of our hands run a wrap so less shock load the better for me. Hands down tho prob one of the best explanations of how to negative rig I've seen keep up the content bud it's good stuff

Good guidance and advice! When you did the slomo of potential damage to the rigging line, I couldn't helping noticing the little puff of "steam" from the rigging rings. Potential heat damage?

Thank you

Some climbers don't tie in a emergency room to repel if needed, I ve seen it a hundred times expesially when doing crane work.. all professional climbers do this.

It would be really nice to have some input for the groundsman as well. Providing a soft catch on smaller material is very easy to do. However, I found it difficult when working with the port-a-wrap taking large pieces similar to what you are showing in this video. My employer has always been a tree climber and actually didn't have very good input as to how to determine the number of wraps and how to let it run with the larger pieces. Perhaps it was the rope diameter in combination with the port-a-wrap we used. Maybe I was just afraid to provide enough slack when managing such large pieces. It is a topic I have found extremely little information on so far. Anyways thanks for all the good content.

My only adition to this would be to have the block/pulley/rings at a 90 degree offset to the directional cut. This serves 2 purposes, it reduces the risk of the lump hitting and pinching the rope but most importantly, it aids to take up the slack and makes the log glance off the trunk instead of falling straight against it basically turning the vertical movement into a lateral movement which in turn also reduces the negative load in my opinion. Its always been much smoother for me with the offset pulley to directional cut

Sometimes a vertical speedline is better than negative rigging.....usually it's better to use a vertical speed than negative rigging

Does the side cuts also help for not having a barber chair happen, should you make them above or below the face cut?

Little simple question : even with a half hitch, should you do littles notches for the rope ok the side to help the rope not slide away?

What's the Name of the Knot you used instad of the Half Hitch ? Tryed to catch the Name but couldn't get it. Greetings from South-West Germany

What is the name of the metal piece you can wrap at the bottom of the tree . When roping .

I left a rigging ring in a tree for a few months. It seems fine but I don’t know. What are your thoughts?

I have a question and it might be a dumb one. Why go through all that trouble rigging up this log that you were going to cut down when you could just drop it to the ground. Is it just a demonstration for a situation where you can’t just drop it to the ground?

Have you ever tried a safebloc for negative rigging or in general?

10 q 4 the great video

Ive gotten used to the idea of using a siberian with a daisy chain instead of a running bowline.. faster amd easier to remove.. i usually stick with a caribeaner tho because why knot?! 😂

I've always tied my cow's hitch exactly how Connor does and I've never had any issues. Anyone else tie it this way?

I've noticed when I've watched experienced climbers on KZfaq when they put there face cut in it goes 3/4s of the way back when there logging down. What's the reason for this?

I call it positive rigging, people we'll say I'm wrong! but I don't like negativity on my job site 😂🤓

1st!!!

First

Good for training this site , But when is enough space , all time let fall them down , doesn't matter the English Grass ... Lay over branches to protect the flor Rigging Stems is all time the most dangerous cause there are tons of weights shortly in action 10 or 30 times more then the weight of the wood 🪵

i do not agree with this dropping a log like this , running a log isnt how rigging should be done , you should be using 16 mil Spectra rope with no stretch so the log only drops in one ft below the cut , hench it does no gather extra forces on the rigging rope , if you dropping a branch or head all the way to the ground fair enough , but this isnt the same with a log , and as you can see in your video its why you take a big shake , one day youll break that rope doing this with a log , young climbers today do this with every rig they do , they are afraid they will get hit by the load when really they should be watching were they are and were the load is going , older climbers knew the forces on rigging ropes and yes we had lowering devices even 30 years ago , ( Don Blairs Hobbs device ) , we knew that lowering large logs just below our feet would only double the weight on the rope hence why we use Spectra with no stretch , 38 year tree climbing teacher here in Australia .

Excellent presentation. Only one comment, the correct pronunciation of Bowline are UK [ˈbəʊ.lɪn] or US [ˈboʊ.lɪn] not "line". All the best from a Swede :)

Thank you