Never buy a Door Frame AGAIN! | How to Make a Door Frame

Never buy a Door Frame AGAIN! | How to Make a Door Frame | D2D DIY

Рет қаралды 987,008

7 жыл бұрын

Get your Shirt on!! bit.ly/DITylerMERCH
You will not believe how easy it is to make a door frame! I have bought new doors so I could replace the frame in the past but NEVER AGAIN! I have made several door frames in the past and it is amazing how simple they are to make, a few boards, screws and wood glue and you are all set.
I made this door frame to accommodate an exterior door that was here at the new house when we bought it. This will provide a well insulated door for the new shop to keep the humidity out and the AC in this summer!
**SUBSCRIBE!!** goo.gl/Pftd4Q
Big thanks to RIDGID for sponsoring our channel check out their latest power tool promotions!
www.ridgid.com/powertools/pro...

Пікірлер: 442

@erichemard7066 3 жыл бұрын

Great job Tyler. The prices of pre-hung interior doors are insane. I built my own frames also, its a little more time consuming but well worth the cost offset. For those who are wondering about the details of the task. Measure the door, add 3/16” to the top and sides. This will give you enough wiggle room in case your rough opening isnt plumb and square. Dont worry about the gap, you wont see it after you staple in the door stop and trim. Someone below mentioned security and the use of shims behind the plunger plate and hinges. I roughed out an extra 1 1/2” and used a 1x in those critical area vs using shims to get that extra thickness to install longer screws.

@antigov7591 2 жыл бұрын

Thanks. I was just wondering about spacing for the door.

@datFUNKYb Жыл бұрын

The 3/16" is the measurement I lacked. Thank you, sir!

@ITSMONKEYBABY 10 ай бұрын

Awesome advice, thanks!

@seanwhitman799 Күн бұрын

Great explanation, but these imbeciles just won't get it. Let's pray for them.

@BillyMcCord 7 жыл бұрын

Great video Tyler! One thing I have done in the past that help me out is to tack a temp scrap piece across a few inches bottom to complete the square as you are installing the door, and shimming it up then you can pop the piece off and dis-guard. It is especially helpful if you are making 2-3 door frames at a time to help keep your sanity as you move them around prior to install. Keep up the awesome content !

@duddude107 2 жыл бұрын

This was extremely helpful... I used to get irritated with videos that didn't explain every step and every tool but now that I'm a bit more experienced and own all of these tools already, it was extremely refreshing to watch this much shorter visual on how to do it. Don't let anyone criticize for not having enough information - different styles are helpful to different audiences. The 45 minute step-by-step tutorials are annoying as heck to anyone who generally knows what they are doing and are just trying to learn a new technique.

@ITSMONKEYBABY 10 ай бұрын

Facts

@seanwhitman799 Күн бұрын

Exactly!

@Sebastopolmark 7 жыл бұрын

GREAT video Tyler. Yes, these things we default to the box store and spend a fortune on a frame that still needs to be plumbed and squared. These little videos really do help us and remind us to DIY - like Tyler does! !! !!!

@DanielZajic Жыл бұрын

This is such a perfect video. Great job. No useless footage I have to skip through, just *showing* how to do it, that's what I need.

@cynthiadee549 4 жыл бұрын

I am a 70 year old grandmother and I was hesitant about doing this. You have made it clear enough for me to now tackle 8 exterior horse stall doors on my barn. Thank you

@diyallegrobusrepairmods5585 2 жыл бұрын

I can't see how this video helped you do it. This must be your grandson.

@ROYALPRIX 3 ай бұрын

@@diyallegrobusrepairmods5585 It's a frame with a stop in it, not tough to understand.

@eatersofdead Жыл бұрын

Let me show you how to make a door frame for the average Joe. Oh by the way. Do you see mythousands of dollars spent o wood working machineries, yeah I forgot to mention you need a wood shop with all this equipment also. Good luck😂.

@alexs-zq6ni 2 ай бұрын

First thought but still doable. Helped confirm how I need to put together the door frame.

@JasonCollette-eb8mw 10 күн бұрын

Could've used commentary on what materials to get. This is completely useless for my skills.

@jerishull1860 2 жыл бұрын

Hey Tyler! I just installed my first (might be last LOL) door using your video as a guide for building the frame. It turned out great. Mine was a salvaged door, so I had to wing it some with the measurements. Thanks so much for the help!

@thenorthstargirl 2 жыл бұрын

Thank you for making this look so easy and straight forward. I know it's an easy concept but I just needed to see it done once. Other guys make it look like rocket science lol! Thank you so much.

@hollyflowers8367 Жыл бұрын

Great video!!! No nonsense, wasted time. You got right down to it and made it super easy to understand!!! Keep ‘em coming 😁

@felixfromnebraska8648 7 жыл бұрын

Great Job Tyler.....You make it look so simple. Not so much when I hung all of my basement doors.

@user-vr9bl4ek6w 8 ай бұрын

thanks for showing us such great ideas because most of the things in carpentry are easier to make but only needs to know the steps to be followed. Great work Tyler

@ggsmith48906 6 жыл бұрын

Very nice sir! This will be handy when renovating an old house, new pre-hung doors come with frames that aren't the same width as old walls and then one has to mess with jamb extensions etcetera. This way one just rips the frame to the proper width to begin with.

@spangledchela1108 Жыл бұрын

Thank you for making this video! I am not a carpenter and you made this very easy to follow. I was able to install 2 doors the casings and trim from scraps of wood I already had. I am so done with getting ripped off by wanna be contractors/handyman people!

@MaxMogren Жыл бұрын

Very helpful! Installing a new shop door myself. Keep it up Tyler!

@DomDollx Жыл бұрын

Idk if I'm using the wrong set of search words but this is the only well done video I've seen that explains how to install a frame start to finish. Agree w others on needing a bit more clarity about how you installed the face plate and the bold hole. I'm trying to upcycle for home projects anf I'm a newbie so it's hard to find the right videos. Ty

@CReevesMakes 7 жыл бұрын

Great job Tyler. I love the beefy door stop with weatherstripping.

@chantalhenderson6994 3 жыл бұрын

I am just super impressed with your workspace!

@steveslenderman8953 7 жыл бұрын

Great job man, the shop space is looking great!

@Jer_Schmidt 7 жыл бұрын

Love this resourcefulness!

@stevenfoust3782 5 жыл бұрын

A video is worth a million words

@cotwold 3 ай бұрын

Great video, perfect length and level of explanation. So many KZfaqrs videos are way too long for simple projects.

@robthewaywardwoodworker9956 7 жыл бұрын

All I could think when I saw you shimming the jamb was, so I'm not the only one that happens to! Thanks for not editing that out man!! And nice work.

@Smitty-op4ld 5 жыл бұрын

On big commercial sites they shim the jam as well. Better to frame too big before the doors come in and shim them then to frame even a quarter of an inch too small. YESHUA GOD ALMIGHTY bless you.

@nuderide 7 жыл бұрын

From a security standpoint, and just good practice, you should shim directly behind the lockset, and deadbolt if there is. And my preference is to shim behind the hinges too, so you can use longer are screws. Looks good though

@otallono 5 жыл бұрын

I mean, pretty much ANY door frame you build or buy can easily be broken through by a very light kick. It's all wood construction.

@itsJoshW 5 жыл бұрын

@@otallono What Bryan said. I should know. I woke up one day a few years back to my doors all being kicked lol

@gnu160 5 жыл бұрын

Jeremy Barker behind the hinges. Those are your pressure points.

@goji8416 3 жыл бұрын

I usually cut the shims from hickory, or a similar wood with high shock resistance/hardness. Also, take two of the standard four screws out of the hinges and replace them with much longer screws, but with similar head appearance if possible. Same for the lockset, if possible.

@jeremyotero4575 2 жыл бұрын

these are all great points, ive done all of these things as a handyman,, but I would rather play guitar for a living.....

@allthings2allmen 7 жыл бұрын

Now we're talking all kinds of tingly up inside! I believe you wont have problems with these door frames...btw I could not help noticing the nice stack of lumber there drying. you sure got things together there dude! Still thinking back to some videos from a year or so ago with your kids playing in the back and they look up at what dad's doing...they really take in quite more than one might think....anyway it just melts the heart when they look up and say,"that looks great dad!!!"...well Ihave to say this door frame looks great there "dad"!!!

@Ryan-zi1pz 14 күн бұрын

Just what I was looking for. Thank you.

@secularism123 3 жыл бұрын

You workshop is pristine!!! Wow!

@travisbryant8833 7 жыл бұрын

Great video that removes the intimidation from building a door frame. I'll be adding a door to my shop in the near future. Thank you, sir.

@cloudstrifeification 5 жыл бұрын

Good video and make note of the comment below about putting a few 3" screws into the hinges and lock strike plates which will make the door much stronger.

@Vlasko60 5 жыл бұрын

Thanks for the video. I would more info on making sure the hinges are installed correctly on the door and the jamb. I didn't hear you say a word about it.

@dawsie 7 жыл бұрын

I like the way you did this with the door in place 😹😹 last time I did the door frame I had to refit it as the door hole was not squared to the door once I had done it, now if I had placed the door in the frame and then hung it I would have saved my self a lot of grief that's for sure😹😹😹 thanks for sharing this when I go to redo all the doors in the house which I do have to do as they are not wide enough for wheelchair access I will be doing it with the doors in the hole as well 😹😹😹😹😹

@noreen_ann1438 5 жыл бұрын

I like the fact that you up cycle materials. However, it would have been nice to have you explain a little more as you went through the steps. Such as how you came up with the length to cut the jamb, etc. otherwise good video for someone a little more advanced.

@jimd9360 3 жыл бұрын

I should have read your comment before I typed mine. Different wording, but hit all the same points.

@cowboy764 2 жыл бұрын

Nice project, could be a little more heavy duty though.

@chesslover8829 2 жыл бұрын

I had the same comments.

@MAGAMAN 2 жыл бұрын

You measure your door, then add a little bit. How much depends on your floors, if you have a threshold, etc. It's not brain science or rocket surgery.

@MetalRat518 Жыл бұрын

fabulous! video i was looking for Thanks

@chriskenrowan Жыл бұрын

Awesome, perfect video. Brief and to the point.

@RhinoJoe1776 5 жыл бұрын

You da boss Tyler:) Great video man.

@jasonc7846 3 жыл бұрын

Thank you. Trying to hang a custom door on my daughters playhouse. I'm a welder not a carpenter. This made my life so much easier. So simple but I struggled so much. Ha. Thank you again! Liked and subscribed.

@DIYTyler 3 жыл бұрын

Thanks for the Sub Jason, welcome to the channel!

@jamesbinns8528 3 жыл бұрын

Wow. Very good--making your own "pre-hung" door!

@jeffforbes3772 7 жыл бұрын

Another good one! Thanks for sharing.

@ethanperry7459 Жыл бұрын

Super helpful, thanks!

@nunoaquiles81 6 жыл бұрын

Great work!

@timbenks8122 2 жыл бұрын

Great to the point video! Thanks Tyler

@widi.1984 2 жыл бұрын

Dude, that's all that I was looking for. Cheers!

@jonhcontreras 6 жыл бұрын

you're so talented...thank you for sharing..

@karlpopewoodcraft 5 жыл бұрын

Cheers for the info mate im currently building my workshop and coming up to this stage.

@blindkimberly1360 3 жыл бұрын

Easy peasy. Ty.

@matt_williams1015 7 жыл бұрын

Nice job, Tyler!

@hatzlmike1 2 жыл бұрын

Bravo. Old school.

@stephenwatson1873 7 жыл бұрын

You should use a marking gauge when fitting hinges especially if your chopping the hinges to both and frame. You set the marking gauge to the centre of the hinge pin then mark that depth on frame and door and you know to chop out to that depth

@davidj.gallardo4553 4 жыл бұрын

Tyler awesome video, you make it easy to understand.... do you have any tips or suggestions to hang a pair of french doors in my dining room?

@brianabouttown256 6 жыл бұрын

Nicely done! St Joseph watching over your workshop is a great touch too

@KSFWG 7 жыл бұрын

Nice one, Tyler! The door and all looks great. Now, before you install the trim around the door, paint it orange! lol

@barbertongold Жыл бұрын

V nice video, well done and THANK YOU

@plsniper 4 ай бұрын

Exactly what I was looking for. Subscribed!

@Mitermikeswoodshop 7 жыл бұрын

nice job Tyler, i did the same thing a few months ago with an inside door, will never buy a prehung again....lol.

@dalewilliamson1125 7 жыл бұрын

Nice job Tyler!!!

@LivefreeanddiyTv 7 жыл бұрын

Simple and sweet, just need to put some trim around it... nice work 🤓👍

@uu35 3 жыл бұрын

Great video. Questions... Is that pine wood you used? What is the preferable type of wood? How thick and wide are the boards? Thanks.

@edadpops1709 7 жыл бұрын

Nice work tyler. I hate hanging doors.period,such a pain in the arse. On my shop door which was a solid core reuse store unit, i built the king studs from 4x4 with a 2x4 trimmer stud.i drilled the hinge holes out and used 6" screws 2 per hinge. Not kosher but very strong. I hate hanging doors.

@terryoconnor1744 2 жыл бұрын

Great video! I was wondering what length the screws were for the hinges? Did they go through the 1x4's much?

@hior12israel49 Жыл бұрын

Thank you for this, so simple...

@kellystott1141 2 жыл бұрын

Hi Tyler. I loved your video U saw and understood every step however I am doing this for the very first time and I just need a little more direction. Thank you

@petejoseph8257 5 жыл бұрын

Good informative vid, that’s a little more difficult than it looks but vid covered the steps involved.

@brockowings4138 Жыл бұрын

I’m glad I actually watched this video. I wouldn’t have thought to build the door frame and door on the ground first and then installing it. I’m sure it saved a lot of screw up for tomorrow. 😂 I was wondering how I was gonna make sure everything was squared and leveled, especially since they’re new French doors going to an office. Everything makes since now.

@MakingStuffco 7 жыл бұрын

It is really so simple and they are expensive! Nice job!

@darrylsmart1783 6 жыл бұрын

Will try that one next time !!

@MelsDiner115 3 жыл бұрын

Great vid if you have free door and right tools. Thanks for sharing.

@laishmorse4668 7 жыл бұрын

Great video, thank you.

@josephponcik2641 7 жыл бұрын

great job and timing i need to put in a new interior door

@joemadrid8331 3 жыл бұрын

Good job Tyler!

@alankwong7182 5 жыл бұрын

Thank you for showing without all the talking of other videos! Love your setup.

@lancenguyen9175 Жыл бұрын

That was pretty cool.

@weekendwarrior3420 2 жыл бұрын

After a big well-known door company failed twice to prehang a $3000 door (couldn't even mortise hinges to the same depth, let alone mortise them in the right place), I decided to just buy slabs and make my own frames for all doors in my remodel. It's really gotten that bad.

@DiegoHernandezLikesBikes 3 жыл бұрын

TYLER! Awesome video!

@wolfy1 5 жыл бұрын

THANK YOU. I can do this!

@Remodelaholic Жыл бұрын

Nice work! Thanks for the video!

@artravision 4 жыл бұрын

Fantastic. Thanks!

@JoseMora-mn2kz 4 жыл бұрын

Excellent work greetings from mexico

@bunhead8 5 жыл бұрын

enjoyed the video but would have appreciated more explanation of what you are doing - also, I don't have all the special tools you used, there must be other ways of making cut-outs etc. thanks

@joshuaparnell1694 5 жыл бұрын

As far as mortising the hinges, you can use a $5 set of wood chisels instead of a router. It'll take longer, but definitely will get the job done (but realistically, you can get a cordless router for less than $75 easily, and for significantly cheaper if you search on Craigslist or Facebook Marketplace). The door catch is with a simple drill and Forstner bit. Home Depot has an 8 pack of various sizes for $20, and decent cordless drills can be bought for $50 to $75. And personally, I think he was going a little overkill using the multi tool to cut off the shims, but to each their own. Just as easily done with a flush cut saw ($13 at Home Depot).

@bobbyprivate 3 жыл бұрын

Brilliant job. 💎💎💎

@gordonlam2757 7 жыл бұрын

Tyler that was a good video, what was that tool you used to notch out the door hinge area so that it was recessed a bit to accomadate the thickness of the hinge plate?

@joseartiaga3048 4 жыл бұрын

Great video. Loved it

@chrismalcheski9232 4 жыл бұрын

Looks like 8 screws across 4 corners and you have your basic frame. Awesome video!!!!

@sharonrichards1627 6 жыл бұрын

Helps having a shop full of great tools.

@DIYTyler 6 жыл бұрын

Ok, I see what is stopping you now....my bad.

@durvalrebelo2624 2 жыл бұрын

Nice job.👍

@peterharper9703 4 жыл бұрын

Great Job... I’ll take 4 of them please!😜

@WesHamstra 7 жыл бұрын

Good job. I hung 4 doors in my old house this way. Its allot cheaper to make your own jambs

@infinityphoenix822 4 жыл бұрын

Great detailed instructions in our terminology..... I have a question is it possible to make a door frame for a commercial sized aluminum glass door 36 by 80 in?

@FrixnFactor 3 жыл бұрын

kickass video thank you!

@matthewsheets7188 3 жыл бұрын

Thank you.

@davidholland6061 2 жыл бұрын

Dood that was awesome 😎

@TerrydeAlaska 4 жыл бұрын

I really enjoyed the video, but I would have loved to see more detail and thoughts behind what you did. Also what about the threshold part of the door? Thanks...

@rodneymackey4325 4 жыл бұрын

no threshold on an inside door

@lordvader1342 6 жыл бұрын

Excellent video.

@chrisgro7660 7 жыл бұрын

I'm new to your channel but I take it you like ridgid, I have quite a few but some are better than others.

@1bossou 4 жыл бұрын

Awesome job

@agalpalacio9157 4 жыл бұрын

You made it look easy, what ain’t easy is that fancy high tech workshop you got, you seem to have all the work surfaces and tools

@DIYTyler 4 жыл бұрын

Only use 3-4 tools if you actually watch. That's a great excuse though.

@nekfolzter0707 2 жыл бұрын

Like your video. Was hoping you was doing one with a threshold plate for an exterior entry. Going to attempt one but don't have the sweeper seal yet & I'm not sure how much space to allow for that. A seal I looked up is 7/8ths but seems you'd want to have it touch some. One thing I read said 1" but how could it seal with 1/8th gap? I was thinking 3/4" that way it'd be 1/8" of sweep sealing. Any thoughts?