Never seen before Brakeline Flaring Hack! How to repair leaking fitting.

Рет қаралды 187,536

Жыл бұрын

Today i had a brakeline leaking that i just made. This old trick is really handy. You will need a cordless drill and some valve grinding compound for this trick. Hope u like the video. Thanks for watching.
#outlawedge #mnoutlawcustoms #flaringtool #brakeline #toolhack #viralvideo #tooltrick #hack
Check out these channels!
@IronHorseGarage @NZMOPAR @ironoutlaws3554
@DGRetroCustoms @EdgeofEternityBillCameron
@DesertRatFabrication @RoyMarkosGarageRMG
@Kevscancave @kimber1958 @Coverman66
@KUGW @honestpeytonsspeedshop @HooptieDoodle

Пікірлер: 319

@stevesautorepair 3 ай бұрын

Been running a garage for 27 years and have never had this issue. Getting a better tool would certainly be a start

@MrHughk1 3 ай бұрын

Idiot has overtightened the tool, there is a reason the come with wing nuts for hand tightening.

@Sabe53 3 ай бұрын

I use Eastwood's vise mount flaring tool and never have anything that looks like this.

@jimthompson3030 3 ай бұрын

all tools are chinese junk even new parts are junk

@liuj88 2 ай бұрын

@@jimthompson3030 His tool clearly says "MADE IN USA". You're not just an ignorant bigot, you're a blind ignorant bigot.

@liuj88 2 ай бұрын

@@jimthompson3030 His tool clearly shows "MADE IN USA". You're not only presumptuous and illogical, but also blind.

@stevefortin7504 3 ай бұрын

Never seen before,,,, dont ever want to see it again.

@Dragcnborn Ай бұрын

xddd

@troymecey 2 ай бұрын

So many on here have commented that you don't know what you're doing and how good they are instead of saying- good job figuring out how to fix the problem you have using what you have INSTEAD of buying another tool. I have a brand new tool with the fancy case and it does this on steel tubing also. I just use a small file. Glad you found a good solution, I'll have to try it.

@rated_tox1c990 2 ай бұрын

Definitely

@CaptainKevinandCarol Ай бұрын

Unbelievable 😮

@orboakin8074 18 күн бұрын

A small file? Interesting. I am currently fixing my Pontiac g3 2010 which I bought last year and the old lines were really rusted so i change some portions. The ones I did are leaking draining brake fluid so I will try the file.

@stevecobratei8538 6 күн бұрын

Did you ever thing so many people send things like that because its true. If he and you did not over tighten the flaring bar, you would not have the grooves. Some light sandpaper, grinding compund, whatever you use. Its not needed. If you put grooves in the line just leave them. They will support the line inside to nut. The tighter the fit the best. Yes I am a Master technician, 50+ years

@BlainesGarage 4 ай бұрын

Not necessary. The ridge on the actual flared area will go away when you tighten the nut down. The nut and inverted flare inside the fitting will finish forming the line flare to the proper shape. Done

@drewnicest4319 3 ай бұрын

I was thinking the same thing

@bigredbeard65 3 ай бұрын

I've done a lot of flaring in my years as a mechanic and I've never needed anything like this, first he's introducing a foreign substance and he's adding unnecessary wear to the flare and the nut and very possibly damaging the threads on the nut. This is a very bad thing to do, I for one will never recommend anything like this.

@johnbrooks9523 3 ай бұрын

@@bigredbeard65 I'm with you all the way. I learned to not go so heavy when forming the second part of the flare which leaves the flare slightly compressable. This allows the female fitting & the flare nut to perform the final shaping. Adding a very tiny amount of rubber grease to THE THREAD ONLY, then nipping the nut up, backing it off & nipping it up a few times gives a perfect seal. That small amount of rubber grease tends to seal moisture our of the thread preventing rust & enabling it to be easily undone in future if necessary. There's no way I'd ever introduce valve grinding paste to the chuck of my drill & I'd eat valve grinding paste before I'd allow it anywhere near any brake hydraulic component. BIG NO NO!

@babaoreally8220 2 ай бұрын

Agreed,the mini-ridges on the tubing,under the fitting and below the flare,have nothing to do with seating of the flare upon the seat.Only a poorly shaped flare or a damaged seat will allow leakage.I’ve done tons of these,and you can go overboard on the depth of the flare.Basically,the shape of the flare must match the contour of the seat.It’s much like over torquing a bolt,more is not always better,it takes some skills and experience doing this.

@liuj88 2 ай бұрын

@@johnbrooks9523 Amateur here. What is rubber grease? Silicone?

@frankjones4094 Жыл бұрын

The face of the flare is what seals against the fitting it's threaded into.

@michaelallen5505 6 ай бұрын

This was my thought as well. The seal is on the inside of the flare. I'm not sure if a bump on the outside would cause a leak. Maybe due to unequal pressure? A common leak fix is to simply loosen and retighten 2 or 3 times to help seat the inside of the flare.

@garyszewc3339 3 ай бұрын

Yeah, this guy is an idiot. He also put the lapping compound into the line, which contaminated the system.

@user-gj8oq7fw1u 3 ай бұрын

this guy doesnt know what he talking about, what a waste of time.

@Xmonders 3 ай бұрын

Thnx for sharing Sir!! It is always Nice to see some new cool tricks. I am a 31 yrs Chrysler Tech and still working . That Imperfection area what you have shown not really can cause any issue because when you start to tighten the nut, the pressure of the nut will force the opening of the flare to seat against the other side of the line fitting automatically or you may call it 'self compressed sealing'. Unless the flare was made way out of shape. Otherwise not too worry. But it is nice to see something new that I have never seen to smooth out the flare and the line with its nut. Thanks again sir!

@tylerhaldeman2199 8 ай бұрын

Thank you so much just spent the entire weekend without the result I needed this might’ve solved my problem

@poellot 3 ай бұрын

I needed to make an iso flair, i decided to buy the good vice mount flair tool. I think it is an eastwood. Worked perfectly. Pretty expensive but it was worth it just for one vehicle making all new lines vs taking it to a shop or trying to order premade oem lines.

@terryatkinson3182 3 ай бұрын

There's a better tool that looks like a screwdriver, top half comes off and put pipe inside then bolt it together and the flair making piece is treaded so screw it on with a spanner and flair is done. For double flair flip the piece 180' and screw that on. Remove piece and open the tool to remove pipe. Thing is you can repair pipes on the car if necessary.

@anthonynapier4668 Жыл бұрын

Good tip on seating flare fitting s man ,,,,I can definitely use that 👍 👍 👍 👍

@briankinnear7461 Жыл бұрын

Great tip. Thanks for sharing. Be safe and stay well.

@EdgeofEternityBillCameron Жыл бұрын

That is awesome!! Love that hack!

@rchydrozz751 3 ай бұрын

I have always been a believer in lapping two parts together to make them fit better.

@roberttill3787 Жыл бұрын

My advice would be throw the flaring tool away and buy a new one that doesnt leave marks on the pipe.

@davidshepherd-sj2tj 3 ай бұрын

Obviously or and also quit using the high copper content soft line

@williamrosenow6176 3 ай бұрын

Use the old one he showed that has a hand tighten wing nut. Put a nut on that old one instead of the wing nut and crank it down would probably damage the line too.

@peternewman3487 3 ай бұрын

Yes I agree. That flaring tool is a toy. Buy a professional flaring tool like I did in the early eighties and it’s still going strong.

@r.joseph8911 3 ай бұрын

Yes, I have one from the ‘90s made by either Lisle or OTC. It’s amazing, has the hand-tighten wing nuts and a nice little case for everything.

@Imageloading... 3 ай бұрын

What tool holds the line tight enough to not slip, but doesn't leave marks on the copper-nickel line?

@kimber1958 Жыл бұрын

Very helpful always struggled with that tool

@jimsix9929 2 ай бұрын

great tip, I have a very good flaring tool but I have got leakers before, I think it would be a good practice on every job, that one leak out of a thousand will cost a lot in time and headaches

@alext8828 2 ай бұрын

Great Idea! Thank you.

@LandsharkGarage Жыл бұрын

Man what a great hack brother! I always pick up something from your videos. Keep up the good work !

@pkg7267 3 ай бұрын

Thanks for the tip brother man. 👍🏼

@leh3827 3 ай бұрын

Folks, it's obviously not a problem all of the time but what a fine solution. Also: Maybe some other brands of flare tools don't mark it up so bad but what if you didn't have one of those. The poster has two tools there; it looks like he might have been trying different ones.

@erno9248 3 ай бұрын

Thanks for the tip.

@travismathis6084 5 ай бұрын

Awesome thank you!!! It worked for me perfectly!!! 👍🏽👍🏽👍🏽👍🏽 (we work with what we got right 🤓)

@user-ph3ws7qj5t 2 ай бұрын

thanks mate for the awesome tip !!!

@rafaelmoreno79 7 ай бұрын

awesome idea. funny i came across this video as i am just messing around with one of the left over brake line tubing from a job i did a while ago. thanks for the great idea. i hate that serrated line on this tools. is nice to know how to fix it

@revh7478 8 ай бұрын

Awesome, I did the lines on my antique truck and couldn't find out why it was leaking, now I see the problem I have!! THANK you sir!!!

@davidshepherd-sj2tj 3 ай бұрын

Not sure u do if u think this is going to make ur line seal better...js

@one62projects Жыл бұрын

Good tip.

@miguelruiz6691 3 ай бұрын

Great tip, I've had that problem before and end up taking the lines to a professional shop to be made. Wish I have checked your video then. Thank you so much

@davegallucci9327 4 ай бұрын

Great tip, thanks.

@OldGriz406 4 ай бұрын

Great tip!

@philroser8920 Жыл бұрын

Nice tip

@seanbrechin9422 10 ай бұрын

Awesome tip... Four times today, I got nothing but leaks. Tried this without compound and it seems to have worked just fine fifth time round.

@WhiskeyDents 8 күн бұрын

Great idea

@jtreminger 6 ай бұрын

Great advice!

@jackcollins2344 Жыл бұрын

Great tip !!!

@DesertRatFabrication 10 ай бұрын

Nice trick Arco, thanks brother 😀😀

@johnlandry1393 3 ай бұрын

Good idea bud!

@simonilett998 3 ай бұрын

Dang, I think I'd be spending my time more productively going out looking for a decent flaring tool🤣

@timgannon2993 3 ай бұрын

Been making brake lines for 37 years and have never needed to do this ???????

@donharman2104 3 ай бұрын

Those flare tool lines are not a problem. The double flare seals on the inside of the cone, not the outside. All this does is to risk getting a very abrasive compound inside your hydraulic system. This is totally unnecessary.

@Rawrkee 5 ай бұрын

This makes me feel better since you said it’s not flare. I was trippin out and remaking the flares just to find out that they still leaked 😆 ima try this out and I hopefully it fixes the leaks, thanks for sharing!

@rupe53 3 ай бұрын

Most flares leak because you overtightened the flare while making it and there's nothing left to squeeze for the final seating of the two surfaces. I have also found that after cutting the line to length you should clean the inside edge of the tube with a file, the pointed trimmer reem on the cutter, or simply use a wire wheel. Any small burr left on the inside of the tube will give you an uneven flare seat.

@TrendsbySterling Жыл бұрын

Cool trick Arco!

@ABTOPECTABPATOP Жыл бұрын

Well done 👍

@tuckerizer666 3 ай бұрын

Maybe try using compound in the jaws of the flare tool. Steel lines are even worse to double flare.

@stephenrose8188 3 ай бұрын

Unaware of what is generally used 'across the pond' I use a brand called 'Kunifer' which has a % of copper in it. It has many advantages not the least is corrosion resistant, easier to bend than steel, easier to create the flare(s). More maleble all round, as to the marking of the pipe when in the style of clamp shown in the video it doesn't mark as much as steel although I do apply a small amount of grease to the pipe before clamping and flaring. I've made hundreds of brake pipes with this particular pipe, (& steel before I discovered Kunifer)

@richardtidd2738 6 ай бұрын

Excellent video Thank you, Also bevel the line first to help with the first flare.

@KerbsideClassics 3 ай бұрын

great little hack cheers buddy

@robbollom7396 Жыл бұрын

dig it man

@siskiyouwoodsmann4279 3 ай бұрын

Neat idea with the lapping compound, just be careful to keep it out of the inside of the line 🤦🏼‍♂️ Your damn sure going to have a perfect seat on the backside of the flare. Not everyone has a high end flaring tool and your hack if done carefully imo is a great workaround in a pinch!

@reason2gether 3 ай бұрын

I have always just taken a small needle file to hand file the high spots off as needed. Less mess and cleanup. The idea is correct though. The high spots make the seating forces uneven. Highlighting the issue helps those that do not understand the issue to be aware of the issue and how to correct it.

@Slithey7433 2 ай бұрын

My thought too. That little bump will cause uneven compression of the flare. Shouldn’t have to use the fitting to complete the tubing press.

@darrellbryan1203 Жыл бұрын

Neat tip, so simple like following your projects

@moushunter 3 ай бұрын

If your flare met the nut squarely it wouldn't leak. The flare seals the line. If the fluid is leaking it is the flare that isn't working not the markings on the line behind the flare. When you held the nut to the flare at the beginning of the video there was a space between the nut and half of the flare. You may have an issue with the flaring tool or the line had a slight bend in it preventing the nut from seating flush against the back of the seal. I think your valve grinding compound and drill thing seated the nut squarely against the flare completing a good seal.

@jcanfixall1585 3 ай бұрын

Thanks for commenting exactly what was said and shown in the video, without your comment I would not have been sure how much I actually did waste my time watching this video!!!

@user-ds6ur2og5p Ай бұрын

@@jcanfixall1585”how much you actually did waste your time watching this video”so how much time did you actually did waste as opposed to actually not wasting to much of your time that you didn’t actually waste before you actually left a comment for the guy that reassured you that you actually didn’t waste much time at all rhetorically speaking?

@jcanfixall1585 Ай бұрын

@@user-ds6ur2og5p exactly!!!

@johnshowcarbuilder6720 Жыл бұрын

On your brake flaring tool take one of the bolts out on each end put the 1 side with no bolt in thevice close to where your brake line is and use device to hold the tool it won't leave a mark because it won't spread open That's what I have done

@edwinnavarrete3859 8 ай бұрын

U GOT IT... NICE AND EASY EXPLAINED...

@user-iw4zw7qg7f 2 ай бұрын

Great job man

@larrygreen9100 2 ай бұрын

I had this problem the first time I used Ni copper (this is the only line I now use) this ridge don't really hurt anything as people say because it will flatten out when tightened (is just looks like crap) What I did was take a small file to the sharp edges of the jaws and put "a very small" (notice I said very SMALL) tapered edge on them kind of like a conn rod or a main bearing bores have at it's parting line of the caps, still works great without any problem, Living Michigan I only use Ni copper but I'm sure it will still be ok on regular steel lines.

@franksgarage8551 Жыл бұрын

I got away from the old style flaring tool,this being one reason. But when i install line i snug and loosen nut several times, and it seats fitting. A dab of anti-sieze on tube as well.

@MrGGPRI 2 ай бұрын

Using drywall sanding mesh strips to hold the tube in the clamping tool works best; grinding compound is usually lubed or wet and can slip and with these strips the tube will NEVER slip.

@IronHorseGarage Жыл бұрын

Awesome tip! I just spit on it!

@immanutt4442 3 ай бұрын

that's what she said

@Kevscancave Жыл бұрын

Very Cool Hack ! 👍Thanks For The Shout Out 📣Arco!

@michaelorr430 3 ай бұрын

it's called Lapping I believe..

@dnlmachine4287 Ай бұрын

Comments point out pros and cons, good information is good information. One Pro I see with this general idea is smoothing out lines that are being reinstalled. Often the tubing itself is marred or dirty, which prevents the nut fitting from sliding or turning freely when you go to start threading it in. I think if you are careful, it could be useful at certain times. Maybe using some scotch-brite scuff pad in the drill chuck to smoothen the tubing might even work as well. Its SO frustrating fighting the fitting in a tight space when you need to slide it or rotate it using your pinkie nail and lower thumb knuckle, and it catches on a tiny tiny imperfection and jams. Then of course, then line pops out that has had time to collect some residual fluid, and it instantly drains into your eye, along with a nice piece of greasy aluminum chip. Instinctively you flinch or pull away, and now your head has a rusty gash in it and your elbow knocks over the bottle of steering fluid that quickly runs straight under your impact gun. Definitely a source of swearing. Stay gold.

@OutlawEdge Ай бұрын

🤣😆👍

@williamjensen4531 3 ай бұрын

Thanks.

@TheGforcead 3 ай бұрын

You can clean it up with a small flat file it don't make a mess.

@BesseCustomFabrication Жыл бұрын

Good one man! I also use the Ni-Cop tube but have been lucky so far.

@Dancing_Alone_wRentals Жыл бұрын

Definitely a cool trick. tHanks for the video

@Epnka 7 ай бұрын

Brass wire wheel on the bench grinder works pretty sweet for that too.

@wheels-n-tires1846 3 ай бұрын

A clever idea!! Havent had that problem making lines, but a great fix for those lines that are a lil tweaked and the nut is sticky. Almost nothing more annoying than having to wrench that guy in an eighth turn at a time!!!

@RustyInventions-wz6ir 3 ай бұрын

Just found your channel and Subscribed. Very interesting. Thanks

@OutlawEdge 3 ай бұрын

Subbed you back brother. U have some great content! ARCO

@NZMOPAR Жыл бұрын

Good tip if you make a new line and it leaks there little lapping paste to get a good mating surface

@dondouglass6415 3 ай бұрын

Brilliant... Huzzah!!

@broke_dongle 2 ай бұрын

Keeping this in my mental toolbox , just in case .

@georgesam7805 3 ай бұрын

Amazon has a a sweet hydraulic flaring tool with all the fixins. It's way cheaper than a funeral.

@OutlawEdge 3 ай бұрын

lol yup 👍 we actually just got one from Amazon. Thanks

@crazywickedcustoms7272 Жыл бұрын

Nice

@sleeve8651 3 ай бұрын

" NICE ".....! 👍😉

@malcolmyoung7866 6 ай бұрын

Will be applying this wizardry tomorrow.. thanks for sharing..

@stevecobratei8538 6 күн бұрын

Btw good idea. But just don't overtighten the flare bar and you will not have the deep grooves

@damienmikkelsen6056 Жыл бұрын

Crappy camera work yes, but that high def quality makes up for it

@332ARA 2 ай бұрын

I don't know about this application but, what I've done is used lapping compound for was to mate rough threads male and female threads. When there are micro burrs or what ever

@Grimmjar 7 ай бұрын

Get a tool made in germany. No "tricks" no nothin just perfection.

@WoodandMetalGarage Жыл бұрын

like it

@whoiswaynereynolds5457 Жыл бұрын

And it’s all crunchy and whatever and that’s when you go ahead and grub on it

@orboakin8074 18 күн бұрын

Great video! As someone who just started working on my first car (Pontiac g3 2010) I am currently dealing with this issue. Changed a portion of the old brake lines but they are now leaking at the fittings and joint. Glad there is a solution. Can you tell me any method that doesn't involve a drill? I unfortunately don't have any power tools and am still new to fixing cars and driving.

@OutlawEdge 18 күн бұрын

U can literally use your hands bro. Just spin it with that compound on there until it’s nice and shiny 👍

@stanleyszymanski8507 3 ай бұрын

Isn't the seal at the other side of the flare? Contact w the nut doesn't provide a seal.

@stephenrose8188 3 ай бұрын

Correct!

@jimthompson3030 3 ай бұрын

Compression from the nut of the flair both sides is the seal!!!

@Charlie-dv7ev 3 ай бұрын

I bought a hydraulic flaring tool. Makes em nice and pretty.

@markchodroff250 3 ай бұрын

Great repair! But every time you use that tool you need to fix the flare ? Fix the tool,or replace it !

@OutlawEdge 3 ай бұрын

Actually just replaced it with a couple new tools 👍

@timwindsor03 Жыл бұрын

Awesome hack brother. Thanks for sharing. Keep the videos coming. Hope you have an incredible night. Love you guys

@AN-kg4ei 3 ай бұрын

I've been lucky I guess as I've never had a flare leak. I've messed up many and dropped the die many times also. Cool idea though. I use a drill to clean up caliper slide pins but never thought about grinding compound 👍.

@gigmaresh8772 3 ай бұрын

Do you have a suggestion for removing varnish? Have a proportioning valve (never knew why they call a block of brass a valve) that is stuck with a few decades of varnish. Once used B12 to free up the one on my '67 Mustang. Is there anything better?

@OutlawEdge 3 ай бұрын

What about automotive paint reducer? Or another chemical worth trying would be spray on paint remover. Its worth a try 👍

@Slithey7433 2 ай бұрын

@@OutlawEdge Yeah, brake cleaner oughta do it.

@dannyyo7948 2 ай бұрын

This is an Awesome video for people with ODT or ADT or what ever issues they have.

@cephasgunn1993 3 ай бұрын

no lie man, I subscribed because of your camera work and droppin the flare die. fuckin love the style homie. like me when im tryna explain shit. also what i ended up doing when I was flaring was I wrapped the line in a 2 layers of a sitckynote paper. seemed to do the trick too.

@6Doublesix 9 ай бұрын

Perfect, now I just need to remember this next time I'm making brake line, thank you

@scottjeans6184 3 ай бұрын

Valve lapping compound.✌️

@chucksmith7166 2 ай бұрын

That’s what she said!!!😁

@soupflood 5 күн бұрын

The inside of the flare seals against a rubber o-ring (sometimes even Teflon in propane tubing). The best thing to do is avoid creating the ridge in the first place.

@chucktripp5722 Жыл бұрын

The Eastwood tool will do stainless perfect , I have five flaring tool that is the only one. I actually am going to sell mine , retiring from building cars..

@mr.barney8147 10 ай бұрын

Hey so what would that cause? When i install the fitting all the way tight, the brake line is loose. It can wiggle up and down. Is that bc of this or my flare? Thanks

@OutlawEdge 10 ай бұрын

Most likely because the fitting is to big. If you have a 3/16 inch fitting you must use 3/16 inch brake line. But I have done this before and used a quarter inch fitting with 3/16 inch brake line and it was very sloppy and loose inside the hole. Try putting a bubble flare on the line or making sure the flare is correct. Hope this helps bro. ARCO

@stevecobratei8538 6 күн бұрын

I have had to fix too many vehicles brakes because someone thought they knew what they were doing.