Its nice to see more companies offering more products for the powerstroke. We finally have more choices.

Thanks so much Arod. I just did this job following your video. It went pretty smooth and took me about 40 minutes. Not too bad for a 70 something desk jockey.

Yes sir! Recently installed this s&b tube on my '18 powerstroke great upgrade. Being in California, I can't wait for s&b to get the hot side tube carb compliant!

It starts with a simple CAC pipe upgrade. Before you know it you're installing compound turbskis!

I just installed the Doorman version of the same today on my 11 with 219,000m. It’s stainless steel, very robust and about a hundred bucks less. All business. I haven’t had a problem with the OE pipe but spend a lot of time in the back country and now it’s one less thing to worry about.

ARod, you have to stop costing me money. Looks like I need another upgrade. Another great video🙌🏻

Love S&B products. Recently put their silicone body mounts on my 2015 F-250. Would have purchased this cold side pipe if it was available last year when my factory pipe cracked. Went with the H&S silicone hose and it’s been solid so far.

Not yet.. soon as I pay off my Carli suspension, Ill be doing the Intake and cold side.

I have the S&B air intake and the cold side pipe just as you. I have a 2019 F250 and Love both upgrades. The only difference in my install is I cleaned the censor before reinstalling it. Truck runs noticeable smother at idle and accelerates smother, also.

Well I just installed mine today I do have the s&b air cleaner now I'm looking at the 65 gallon fuel tank I ordered mine I'm just waiting for the delivery it might be a week to 10 days thank you for putting out these videos and you're right I did look up under the hood I don't think anybody's going to have a problem with a dealer putting a better part on there for the cold air pipe the other one when I took it off it's so flimsy and it looks like it's got a split already the truck has less than a thousand miles thank you again

I’m running a Rudy’s diesel cold side kit. Very tight fit but so far so good. 50,000 miles on the kit.

'15 6.7 was completely factory and blew the cold side pipe with less than 30k miles. been running a sinister cold side pipe since and after tuning and etc., S&B intakes are the only way to go on these trucks

Been using a H&S cold side stainless pipe for about 4 years now. No issues with the factory pipe, just wanted the insurance.

H&S on my 15. That was the only one out there when I did mine

Very nice after the plastic part I put back the factory on but I do have the S&B air filter on my 16 6.7. Thanks for sharing ARod

I put on a Pusher hot and cold pipe w/throttle valve adapter, red powder coat

That, Mr Arod, is a mighty fine looking upgrade!!! 😍 outstanding 👏🏻👏🏻👏🏻

Love your truck, I ordered the exact looking one about a month ago. 22 F-250 Lariat 6.7 with Black Appearance package and Lariat Ultimate package. Never been so excited to get a new truck! Watching your vids makes me want mine so bad! Hurry up ford!

Going to install this s&b cold side pipe today, busted while towing. 1st truck out of 4. @ 181k miles

I just installed the S&B cold side in my 2016 F-350 the factory one busted around 300,000 miles

Much cleaner and easier than the Pusher brand cold intake.

nice. that aluminum pipe and hose looks beter and can hold pressure beter. than plastic

I really appreciate your content/information. Just wish that I could find someone like you in Chattanooga area.

SPE hot and cold side...6 months ago that was the thing...things change fast I guess. No issues so far.

"Killswitch Engaged"🤘🏼

Went with the h&s all silicone cold side. Seems to do the job nicely.

sinister diesel coldside and hotside pipe kit to match my cold air intake

great video thanks for posting I have one ordered and it looks fairly straight foreword to install

Well I guess I will wait intill the new cold parts company again. It's to bad that mind left me a few months ago. But will most likely to get it and keep it in the truck for the next time the oem blows again.

Just today ordered the cold air intake and intercooler pipe for my 2021 6.7L

Love the S&B product line for the baddest truck on the road. Great content as usual ARod keep it slick.

Running an spe unit!! This one looks Awsome sir! I have also done some experimenting with a few different cold air intakes as well and landed on s&b. If you are running e on tuning s&b is the only way to go!! Factory Flow across the maf is critical for proper afr unless you are planning to do custom tuning on a dyno to calibrate afr. My truck ran like crap with several of the cold air intakes that I tested

I have a Mishimoto intercooler and CAC pipes I will be installing either this weekend or next. I currently have the S&B CAI and am logging IATs and turbine outlet temps after the swap. I'm looking forward to a gain in performance (in addition to what I got from the CAI) and lower temps from the new CAC pipes and intercooler. Also I'm patiently waiting for the arrival of my Banks Derringer.

Looks like a quality mod. Also nice delete.

Love ur videos man. I’m running an mpd full piping kit now. Before I had the H&S cold side pipe, it was a nice piece too.

Quality parts and it looks good too.

Good grief, just take my credit card already…🤣👊🏻🇺🇸

Great video! Love S&B products.

Another awsome vidio thanks !!!

Does that void his warranty how many miles is on the super duty I am ready to install one on mine Love you're video's

Which is your preferred cold pipe S&B or H&S !

Great video I am in the market been researching was going to go with spe but there design looks to much like the factory one that fails and they have negative comments on parts not shipping out after they been payed your video made it clear for me I am buying s&b

Smedling has a one piece with (needs tune) or without ( no tune) piece to remove the butterfly for 150$ both are same price please excuse my explanation

Hey Arod quick question. I just purchased this for my 22 F350 waiting on delivery. I also listed you and your KZfaq channel for how I heard about product. My question is does this do anything other than just reliability and looks? I get it’s pretty hard to improve a relatively short pipe with just better than OE material but there has to be a gimmick or purpose for replacing I also noticed on website they have hot side replacement. If you look at Ford original equipment the hot side seems pretty much fine metal pipe rubber boots. Your thoughts?

firewoodfred says "looks sweet" wait till I show you what I got ya !!!

I hand tighten with an 11m socket and honestly it just kept tightening which very little effort until the spring was completely compressed then snugged it up. It looks like your springs still had some compression left. Anyone else with same experience? I literally just finished install and started it up and reved it up but won’t be able to put load test until tomorrow. I’m assuming tight is tight and it would take some serious pressure to collapse the metal intercooler connection.

👍🏻

I have to get a 6.7 now! You have me interested

Great as usual

I’ve had a few different versions on my truck and have boost leaks at the CAC connection point as the silicone boot and oily air don’t seem to jive well. Not certain why it’s happened but the boost leaks were quite obvious when my mass flow dropped near 75-80 grams per second. Even did the hairspray trick with stronger clamps and it leaked. Replaced it with a stock unit for now until I can find another solution. Both options I used were from HS.

I need those s&b parts

Super video but I have a question seeing as you work for Ford if you put that kit on a brand new truck with under a thousand miles will that void your bumper to bumper warranty you would know you're in the field I'm not I want to order the s&b but I don't want to do something that's going to void the warranty I have a 6.7 diesel let me know thank you for the good videos you put out

I had to replace my hose on my 2019 because of the crack. This looks like a much better upgrade. What sensor is that in the tube?

👍

Hey Aaron, that looks awesome. I have a Ford extended warranty on my 2016. Will this cause an issue with the warranty?

Do you like this S&b cold side intercooler pipe better than the HSM intercooler pipe?

What is your experiences on the 2017+ factory intercooler leaking coolant into the intake? I feel like the need to upgrading to Mishimoto or No Limit Fab intercooler.

I got a Pusher pipe.

Ironically I just noticed a used diesel oil smell today coming in my vents. Anyone that does their own oil changed knows what used diesel oil smells like. Anywho, my hose split about 3 inches right on top. I called S&B but they don't have an EO number yet on this product for CARB areas (f*ck California). Looks like I have to ship out of state and then back home. They definitely make nice products though.

When will you be showing the one for the 11-16

I changed my pipe with an oem hose because of a crack and now I keep getting dtc “P2074 manifold absolutely pressure/mass airflow-throttle position”. It came with a new sensor. What the….

Very cool install. How prone are those to rupturing?

I have a 2015 and was wanting to upgrade the cold side pipe. I been looking at the sinister , S&B, and H&S. Is one more reliable than the other ? Thanks for any advice

6 months left on extended (Premium Care) warranty. Will this void the Warranty? Thank you.

I need that!

Could this upgrade help with a check engine light I am getting? 2011 F350 6.7 getting a p026a after towing a 16k Fifth Wheel up steep grades for long periods of time. Had a shop check it out and they couldn't find anything wrong with the CAC and said the radiators were clogged, so they took the radiator stack apart and cleaned everything. Still getting the same code though.

So how will S&B products affect my factory and extended warranty that my dealer sold me when I bought the new truck? I wanna buy these products, but am extremely hesitant on getting them because of that warranty. Looking at the DP kit and the fuel filter kit to be more specific. Talked to my service advisor and he said ANY aftermarket parts whether there an upgrade and better than factory will be on my dime.

Hey brother quick question my f250 is getting full at 13 gallons of fuel and gauge does not say full never been able to put more than. 13 gallons in it what do you think the problem could be I appreciate your time thank you

For the 2020 wasn’t this one of many issues that Ford fixed???

I been struggling with the code p0170 I have changed several parts regarding the code but nothing seems to fix the problem

It appears your missing some emissions equipment 😂 will there be a video on that subject?

I wonder if this would void any warranty’s?

Any discount code?

Hey do you know if this pipe voids my warranty?? Thanks!

HSM or Pusher???

Was that on a '21 Super Duty?

I see that truck has been deleted. Does this part need a tune required or can it be install in a stock truck.

What about the hot side???

Will this void my warranty on my truck?

Noice

I know this is old but curious, more recently you installed HSM tubes………which is better? I order3d the HSM

I changed my pipe with an oem hose because of a crack and now I keep getting dtc “P2074 manifold absolutely pressure/mass airflow-throttle position”. It came with a new sensor. What the….