New School is Old School. Demo Detailing a Bayliner. Heavy oxidation, bad Gelcoat. worse audio.

Рет қаралды 195,578

3 жыл бұрын

How to @ 3:30
• Boat Restoration .Gelc... . If you are looking for a "how to"
I have a ton of videos on this subject. If you're here to learn, I'm here to help.
I did a few short videos on this boat earlier but thought it deserved a bit more of an exposé.
• You asked: this detail...
(4 months later for all the haters out there) learn to use compound correctly and stop the hate, that simple. All the 👎🏽 in the world won't help anyone, leave a comment unless you're a punk who can only do 👎🏽... Say something, use your words or stfu.
I'm not going to share what I did in front of the windshield, that's mine and my student's only. The important thing to know about it is that there's a way. You might figure it out on your own, keep trying.
This boat is a display. I'm doing the starboard bow corner and the port side stern quarter and leaving the rest as found. If this doesn't convince people that we know what we're talking about, I don't know what else to do. I'm not about flashy vids and selling stuff just to make money while not knowing jack-shit about my craft.
Heavy cut wasn't necessarily needed but in spots, it can help.
The light spot on the hull, starboard side is sunlight coming through from the interior side. It isn't a burn-through. If the decals lasted, so did the gelcoat.
Keep Wetsanding if you have time to kill. I have boats to buff and shizz to do.
Want to see the next level to this?
• Would you wetsand Gelc...
I have many more (300+)videos; before and after boat detailing videos including boat waxing, boat buffing...
Have a question? Comments section will be replied to.
🔆🔆Want to help me make some changes @ 3M? Think about giving them a call and tell them to look at my videos. Give them a piece of your mind. Help me light a fire under their butts.
Phone: 1-866-279-1235 (general marine)
Phone: 1-877-666-2277 (waxes and compounding stuff) 🔆🔆
Anyone can hit a rock with a hammer; getting the rock to look like something that belongs in museums and books... Takes a love of hitting rocks with a purpose and not just the right tools/products.
I use a DeWalt DWP849X
If I'm going for perfection in gelcoat, I don't use a ceramic (unless a very new boat) I prefer the ease, cost and reliability of Fire Glaze by RMP. Make sure you get all the oxidation out of the gelcoat, get a great finish, clean and strip the surface and then apply Fire Glaze.
www.restructuremarine.com/fir...
(tell them Lee sent you. No discount and I receive nothing but I'd like them to know 😊)
There's a "marine" version but it has the same main ingredient as Fire Glaze, just a different lubricant/carrier solution made to be environment friendly. I find it dries rather fast and as I'm in a hot climate, I use Fire Glaze instead of Restructure Marine Polish. I like their Mirasol spray for all the interior furnishings as well.
For a demo on how I apply this stuff:
• Boat wax, kind of. Fir...
(tell them Lee sent you. No discount and I receive nothing but I'd like them to know 😊)
3M Quick Connect adapter (mfg # 05752) to use with the double-sided compounding pad (3M mfg #05753) or the double-sided polishing pad (3M mfg #05754)
Foam compounding pads 3M (05737-discontinued but awesome)
or (05723-new version 😑)
3M Super-Duty (05954)
3M Perfect It Heavy Cutting Compound (36102)
Perfect-it ex ac compounds by 3M (36060)
Meguiar’s (owned by 3M) Flagship Premium Wax (M6332) Pro Polish by Shurehold or 3M's liquid wax with scotchguard.
I receive no payment for listing these items. I list them because you guys ask and I just thought I would save some time.
Wear protective gear, this stuff can cause cancer and kill you.
If you are a fan of what I do, I don't take money from manufacturing companies or product suppliers.
www.paypal.me/DDLee
Thanks for your time and support.
Lee

Пікірлер: 458

@futureboigaming5599 2 жыл бұрын

As a detailer that operates and deals with heavy oxidation in south Florida, I can second this motion of sticking to using heavy cut compounds. It saves everyone involved time and money from wet-sanding. I couldn’t here more encouraging words when you said that if you just use heavy cut correctly you won’t really need wet sanding. Respect your grind brother, love from soflo 🤙

@Local_Boydidgood 2 жыл бұрын

The luv gets returned, thanks. Stay hydrated brother. I might have heat but there's no humidity here, you guys deserve medals for doing this down there!

@richard8297 Жыл бұрын

I'm glad I happened to find this video. I recently bought a used boat which has a broad band of red on the hull, and I was pretty much expecting to have to go down the vinyl wrap route, as the red is so faded. It's nowhere near as bad as the red was in your video though, so now I am inspired to get compounding and polishing, and I am confident of achieving good results. Thank you.

@Local_Boydidgood Жыл бұрын

That's cool and exactly why I made that video. Best of luck. Lee

@gregeastman216 Жыл бұрын

Learned from watching your videos. My boat looks new again. Thank you

@Local_Boydidgood Жыл бұрын

Good stuff to hear, thanks! Lee

@divindave6117 2 жыл бұрын

I helped a friend detail her boat this past Spring. It took a week of both of us working all day long on the damn thing. I wish I had seen this video first. Everyone I talked to said you have to wet sand over and over going up in grit. then light compound/ polish then wax. Everyone said that. Im gonna call some of them tomorrow and give them grief. PS, that boat sure did look good when we finally finished it. I dare say probably better than new.

@Local_Boydidgood 2 жыл бұрын

Many ways to skin a cat but sadly, nobody wants to try new (old actually) stuff. Glad you now know another way. Thanks, Lee

@aaronkelley8909 Жыл бұрын

Just recently found your videos. You’re quite the artist. Nice work.

@Local_Boydidgood Жыл бұрын

Well thanks, feels neat to hear. There's 300+ more videos that have better audio, commentary and instruction. Feel free to look around. Lee

@jehines3 2 жыл бұрын

A good finish as usual. I brush on my compound so I don't fuss with machine speed, but you do a great job varying speed on the spread out and avoid the crazy sling I see in so many yards. I've been brushing on compound since my body shop days as super duty came in a gallon paint can and just like the way it defines my working area. It also helps give even cut across a surface that likes to drink the moisture out of product. When I encounter a boat like this, I start with a 3M 7445 or 7448 scotch pad with good detergent soap to skim the top layer of dead gelcoat off and let it wash away. That much dead oxidization with embedded mold just frustratingly plugs up the pad and takes way too much time to grind away at. A human can only move their arms so many times in one day. If that was a 48' yacht, you'd be at that for 5 days straight on super duty.

@Local_Boydidgood 2 жыл бұрын

Sounds like you've "been there" If a Super-Duty job came in that was the whole 50-100', I'd make all my profit for the year on that boat and mostly would just pass to be honest. I'm just trying to get people to be aware that this is possible without sanding, that's all I'm doing, ever. I appreciate the knowledge and comments! Thanks. Lee

@jehines3 2 жыл бұрын

@@Local_Boydidgood I generally buy boats to clean them up enjoy them for a bit and eventually flip them. My current project is a 2000 Silverton 45 that hasn’t seen a buffer or coat of wax since 2017. I’m giving it a full gelcoat restoration this spring. A Local company wanted $6500 to compound and wax. It’s more than a $6500 job in labor and material if done right so behind the (wool) wheel I go. Some earbuds and good tunes can be somewhat relaxing.

@Local_Boydidgood 2 жыл бұрын

$3,800 and my guys and I would have done that boat in 2 days and used Flagship by Meguiar's the 1st good waxing. Next year, compound out the boat again and use Fire Glaze +. You would then just keep the boat clean throughout the season and reapply the fire glaze + once a year. Flipping can be fun. I've sold some smaller boats, trailerable but only a few big girls. I was a broker a while back and sold some decent sized boats. I wasn't fixing them as just collecting commissions for doing nothing. Gross. @ $100 a ft, I expect to give you perfection. Your detailer in-question didn't want the job or knew how to tackle it. There's plenty of low hanging fruit out there for a hungry buffer. I'm glad you're motivated. Small sections connect to make a large one. Large ones become parts, parts become tops or hulls or sides, back or front. Top down, front to back so you aren't walking over what you spent all day getting perfect. Good luck! Enjoy the tunes and have a cold beverage now and then. Lee

@jimsr.4019 2 жыл бұрын

will this work on ghost stripes too ? I removed some old decal swoohes from the sides and the gelcoat is darker underneath where they were, want it all to match... thanks

@Local_Boydidgood 2 жыл бұрын

You determine that. With some time, yes. With some effort, yes. You can sand it down if needed. Super-Duty should be able to make a dent and Heavy cut should bring it all together after a bit. Every time you buff it, they'll get better.

@lydiaajohnson 3 жыл бұрын

I like to start with 3M super heavy compound and then go to the Perfect It Line on really bad gel coat. But, a good wool pad, the right tool, 3M Perfect It, and good technique will get these results. The right buffer is key. I love my Flex tools. Yeah, they were super costly, but I love the way they work and feel cutting my work by a 1/3.

@Local_Boydidgood 3 жыл бұрын

Hi, I agree, the trick isn't tools or products. You might try the yellow/black. I helped design the DeWalt DWP849X. Out of 17 improvements specifically for gelcoat use, they took 14. and I've all the rest, even flex tools. I find them great for cars or smaller boats that are in good condition. Nothing lasts like the DeWalt. I push harder and longer than anyone I've ever seen with this style of tool and I'm on my 5th year on one tool. 3 on another backup buffer. I've used super duty 2-3 times in 15 years. It definitely has a place but it's horrible for your health and so messy. Try the heavy-cut. It will take an extra turn or two on really bad surfaces but finishes much better. It gets you to where the Perfect it, can be more effective, more quickly. The trade off should be to your liking. Thanks for the comment. These are just my opinions. Everyone has their own style. As long as the end results are the same, cool! Thanks for watching.

@Spacesprocketz Жыл бұрын

Thought I stumbled across an old video of Dax Shepard but all jokes aside this video is going to help me a lot with working on my hull this off season! Thanks!

@Local_Boydidgood Жыл бұрын

Well, I appreciate the kind words. I have about 300 more videos for you to watch if you're really interested. This was just a demo.

@johnhubbard6262 2 жыл бұрын

Ok, this beats the hell out of how I restore fiberglass showers in rentals. (Using Gel-Gloss). Great info, thank you.

@Local_Boydidgood 2 жыл бұрын

Gelcoat is gelcoat. 😊

@choimdachoim9491 2 жыл бұрын

I started to compliment your set of music and I see you identified all of it...right thing to do. I really liked all of it and at a perfect volume. Your years of experience make it look easy...I'm about to find out on my newly purchased 30 year old boat that same color. I feel like I'm stealing from you.

@Local_Boydidgood 2 жыл бұрын

Learning, not stealing. Subtle difference however, if you teach someone else.. Now you've tricked the universe. Best of luck. I'll be around. You're the only one who likes that music, or you're sarcastic. Either way, 🤣👍🏼

@choimdachoim9491 2 жыл бұрын

@@Local_Boydidgood Nope. I went straight to the first piece of music's youtube page and subscribed. It reminds me of some of the music I create. All the rest of the pieces you used were good too but the first is my favorite. I'm going to play it for my wife when she wakes up to see what she says.

@Local_Boydidgood 2 жыл бұрын

Or, you really like messing with her 1st thing in the morning. LOL Well, I'm happy to hear someone likes it. I've gotten flamed for it since uploading it. I suppose with my attitude, I shouldn't care if there are people who don't like it. Nope, don't care and now I know someone out there thought it was an interesting sound combo so I'm good. Thanks for reaching out and saying Hi. I appreciate the moment.

@robertmartin265 5 ай бұрын

What works to get faded black paint off the bottom of the hull? Re paint it?

@Local_Boydidgood 5 ай бұрын

Any way you do it, you'll want eye and lung protection. Last time we did this on our boat, we hauled it out and began power sanding it down to gelcoat. We then layered up 2 coats of 'Hullspeed' bottom paint. That's lasted a really long time, I've seen my old boat in the last year and the bottom paint is mostly there after 7-8 years. If just the sides are bad, scuff them up with some rough sandpaper, clean/dry then yes re-paint. Try to catch the debris in a tarp or water trap. Preferably do this at a real boat yard and help keep lakes and rivers clean-ish. You can not remain clean and do this work. I would only have done it for our own boat. I'd pay someone to do it next time. Added bonus: when repainting, scuff and clean up above the old (pre measured waterline and go up from that by 2 inches (about just the length of a thumb) You'll enjoy cleaning less buildup along the waterline this season. I'm no expert, youtube is full of them. Good luck, thanks for watching. Lee

@javancross6085 2 жыл бұрын

Will this process work well on aluminum boats, too. i recently purchased an Alumacraft that was stored in a lean-to shed for years before I began its life stored indoors unless on the water.

@Local_Boydidgood 2 жыл бұрын

kzfaq.info/get/bejne/h9h2YLCUp7WpeIU.html This video would be a better choice. You can try but aluminum is a whole different beast, like paint is a different beast. Tell him I said Hi. And luck. Sorry I can't offer you more.

@derekbuchanan5839 Жыл бұрын

Can say for sure this works a treat. Right compounds, right pads and right technique. I transformed my 37ft blue hulled J110 from oxidised mare to beauty.😊

@Local_Boydidgood Жыл бұрын

Nice! There ya go! I appreciate your comment, thanks! Lee

@antoniekruger8631 2 жыл бұрын

Looks great. Just procured a job just like that. I guess I'll be using 3M then. Thanks for sharing.

@Local_Boydidgood 2 жыл бұрын

Thanks. Anytime brother, good luck!

@buck9739 2 жыл бұрын

You are a artist. I’d like to see the whole boat redone it’s a nice looking old boat

@Local_Boydidgood 2 жыл бұрын

Thanks. Sadly, someone took it away to repower and use. It might be coming back someday.

@Solobolo_101 2 жыл бұрын

I been Doing more & more boats lately , your video gave me a huje insight as to how yo really grab more Shine , I use 800/ 1200/ 2500 grit then 3D #1 with a Wool pad after , then Lake Countries yellow pad with Cherry wax for a Great shine... Your videos Rock bro from The Inland Empire Ca ...

@Local_Boydidgood 2 жыл бұрын

Thanks. I'm glad you found a process that works for you. I also know that sanding before compounding can be a good process. I don't push it but I'm pushing a faster path, not better for some but for most people. Thanks for the comment and I appreciate your support truly. If you want a good wax, Fire Glaze is legitimately the best stuff I've ever used. If you can get to perfection, just try it. It'll blow your mind. (works on cars too)

@russellmohr9758 3 жыл бұрын

PERFECT....THIS IS THE EXACT COLORS OF MY BOAT!!!...THANKS FOR THE VIDEO!!!

@Local_Boydidgood 3 жыл бұрын

Anytime!

@mikestaggs3177 2 жыл бұрын

Have a 2009 Yamaha 232 Limited S that doesn't have oxidation. So, I don't need to do anything besides waxit every six months, right?

@Local_Boydidgood 2 жыл бұрын

Sounds like a great plan. 303 aerospace protectant would do well for you. Meguiar's Flagship or 3m's liquid wax w/scotchguard. Shoot for every 3-4 months and double-down on that assurance. No need to tempt your boat to mess up your plans, that's all she wants to do and you know it. 😉

@tmllanz9159 2 жыл бұрын

I am a new classic wooden boat restorer. I am hoping to get my hands on a fiberglass classic correct craft ski boat. I’ll be giving your techniques a try on that. Tom Do you ever ever buff/polish wooden bright work. Incidentally, I have read most of your comments and dialogue. You are very genuine. Keep it up.

@Local_Boydidgood 2 жыл бұрын

You can research "Plumm Duff" and the m/v Accord. These are 2 boats with various types of varnish. I have polished them for years, before I began posting videos on youtube. Generally, if the varnish or clear emron/imron are in good condition, a foam pad and some Perfect-it ex ac should be all that's required. Clean and protect with Fire Glaze or a good polish that is pH neutral to the finish. As to a correct craft ski boat, the gelcoat tends to be very resistant to Compound, start aggressive and work your way back to Perfect-it ex ac and then use a boat "wax" for the first two seasons until the gelcoat has stabilized (stays oxidation free for a year or longer) then compound to perfection and use Fire Glaze.. I like helping if I can and the questions I receive are from people generally trying to figure this out. In the world of polishing boats, the knowledge base is coming from a paint correction background and has been so molested over 50 years that I understand their frustration. With as many boats as I've done and what I've learned, I feel a certain obligation to divulge some of what I've learned. If I can help someone enjoy their boat or a Detailer to be more efficient and make happier customers, I am honored to do so. Thanks for the comment and your kind words. Lee

@marvg8002 2 жыл бұрын

So slow to cut fast to polish? What speed did you srart at ? I started detailing boats a month ago and was taught to use 1400 rpm all the way we use the 3m products you are using

@Local_Boydidgood 2 жыл бұрын

Whoever taught you that isn't worried about swirls. Go 600. If you try to do what I do, you're going to hurt either the boat or yourself. Watch this for an example of why it doesn't matter really, what speed you go, it doesn't save time usually. The results will be better if you go slow. I go fast because nobody on youtube can do this in the sun to a swirl-free finish, none of the "experts". kzfaq.info/get/bejne/od9dpKuK37DQn2g.html If, if you get really good and confident, you can do what I do but there's no need. Go slow.

@saulcovarrubias9010 2 жыл бұрын

hey brother would you recommend using a micro fiber pad to use for compound? Also do you have a video on how to prep a boat especially red color before adding compound to remove oxidation?

@Local_Boydidgood 2 жыл бұрын

Hi. If I'm compounding, no prep needed for the surface. No sand, no seashells and go! No, microfiber pads are not nearly as strong as wool.

@emlynwebster1121 2 жыл бұрын

i bought my second hand boat from a company out of season and left it there until a few weeks ago i started getting it ready for the season, i am actually too embarrased to do anything with the gelcoat because when i turned up with some polish,wax, etc he just laughed,said it was just rubbish and i should do it properly with sanding and he offered there company to do it for the equivalent of 3000 dollars so i said i just want it tried,tested and in the water so i can bring it home and at the end of the season do it this way and hopefully prove him wrong, i just have to find the correct compound here in Norway :) thankyou for the video!

@Local_Boydidgood 2 жыл бұрын

I will help, any way I can. Enjoy the boat, get familiar with it and then teach it that you are the boss in your off-time. Let me know if I can help. Lee

@emlynwebster1121 2 жыл бұрын

@@Local_Boydidgood brilliant thankyou! i plan on having it at home for next winter so ill be winterizing,changing oil and filters and getting the coat polished and probably any gelcoat repair so ill definately be reaching out thanks :)

@Local_Boydidgood 2 жыл бұрын

I will be here. 😁👍🏼

@markrobbins9552 2 жыл бұрын

Got a 40yr old Wellcraft that in its prime was taxi cab yellow. Now it's sortof inside of a banana then driven through liquid chalk look I tried a couple of compounds and in some places was OK but not consistent. Gave up and went to wet sanding. Have 1/2 of it done, looks good but damn what a pain. Gonna try this stuff. Also trying to see if you're buffing differently than I do. Done a few cars but none of them covered in gel coat. Thanks more than I can say.

@Local_Boydidgood 2 жыл бұрын

Forget what cars taught you. This is not anything like paint. Grinding concrete till shiny, that's what this is. Good luck. Hope my stuff does better and looks right for you. I have over 100 vids on KZfaq, take some time to watch a few, please. There's a theme and a repeatable technique. Get the right wheels and products and I think you'll see a glossy yellow boat soon enough.

@bailey4557 2 жыл бұрын

Lee, My name is Lee also, What machine you suggest for a beginner removing oxidation off the boat that I own? What products did you use? I am in the coastal Carolinas and can't get to you. I have that similar color red Hurricane boat with the same issue

@Local_Boydidgood 2 жыл бұрын

Hi Lee (that feels weird. Lol) Dewalt DWP849X www.restructuremarine.com/fireglaze-products-2 3M Quick Connect adapter (mfg # 05752) to use with the double-sided compounding pad (3M mfg #05753) or the double-sided polishing pad (3M mfg #05754) Foam compounding pads 3M (05737-discontinued but awesome) or (05723-new version 😑) 3M Super-Duty (05954) 3M Perfect It Heavy Cutting Compound (36102) Perfect-it ex ac compounds by 3M (36060) Meguiar’s (owned by 3M) Flagship Premium Wax (M6332) Pro Polish by Shurehold or 3M's liquid wax with scotchguard. I receive no payment for listing these items. I list them because you guys ask and I just thought I would save some time. Wear protective gear, this stuff can cause cancer and kill you.

@billyklercker1736 2 жыл бұрын

What RPMs are you using initially and how high do you go when you have the compound spread evenly and not flying all over the place.

@Local_Boydidgood 2 жыл бұрын

Full slow and full speed.

@russwilkerson2741 3 жыл бұрын

So much said with few words but effective. It gives me hope for my 1984 procraft that I don’t know when or if it was ever buffed or polished. Used to be candy apple red metallic flake. Now looks like root beer🤣😂 Do I even stand a chance. I DO NOT WANT TO WET SAND IT OVER AND OVER AND OVER. you get. Thanks for some inspiration and knowledge. Your comments please.

@Local_Boydidgood 3 жыл бұрын

Try super duty or Heavy cut by 3M. I don't even remember the 2 boats in 15 years I couldn't bring back. Good wool pads and patience. Let the products do the work. Procrafts use good gelcoat. Right underneath all that chalk is your boat, I dare you to prove me wrong! Any vid I have past 15 minutes will have some "how-to" words. Sometimes, I just like letting the work, do the work of talking for me. Happy to hear that I reached someone and possibly helped.

@BlueBeemerBoy77 3 ай бұрын

Thankyou for this video. Im about to do this on my 1992 Sunbird. You dont happen to know where i could find the trim covering the channels of the windows? Looks like same as yours.

@Local_Boydidgood 3 ай бұрын

Hi, this isn't my boat so as far as where to buy parts.. Google? I'm sure there are a few places out there that carry replacement parts or New Old Stock (NOS) parts. Good luck on your boat, glad this video helped. Lee

@juannavarro3620 Жыл бұрын

boat looks beautiful bro. great job.

@Local_Boydidgood Жыл бұрын

Thanks. She came out ok for an old girl.

@dash456789 3 жыл бұрын

Hey long time no see, we met up with Jed and the others when I had my Alpine White M5, and my tiag 540it. I have a 1986 Mirage that could use your expert buffing, it still shines real nice except for the black on the bow around the hatch.

@Local_Boydidgood 3 жыл бұрын

Bring it to Chelan, bring beer. Is it this bad? kzfaq.info/get/bejne/hM99mJyZvNG8j3U.html If so: kzfaq.info/get/bejne/r9t9fJBisbSWp3U.html I got'chu boo.

@8516brian 3 жыл бұрын

OK. Great to know. I think there's a misconception on the part of many boat detailers that there's an infinite amount of gelcoat that one can comfortably grind through. From my perspective - as an automotive paint guy (historically anyway) - there's an increased amount of mystery (i.e., risk) when correcting gelcoat, especially on an older boat that has had multiple owners. I won't work on a car until I've thoroughly assessed the depth, condition and history of the paint. That's tougher to do with most boats, hence the need for even more caution when considering whether or not to sand. So I like your philosophy.

@Local_Boydidgood 3 жыл бұрын

There's a "paint gague" for gelcoat/fiberglass/paint but it's $3,500 so, I tend to accept the risk equally with the owners. I mention the age and possibly going through but it's happened about once a year, out of about 150 boats. I choose to not fear that. I know it's a great time to suggest a respray of paint or gelcoat or a vinyl wrap. I don't see helping a boater overcome a thing like thin gelcoat, stop them from enjoying their boat. I show them alternatives. We always start with the lightest stuff 1st but gelcoat is 20 times thicker than paint and marine paint is very resilient and easy to keep up without grinding. Getting a customer to come in every 6 months (needed or not) for a wax is better than waiting to see oxidation before they call, I hate that.

@8516brian 3 жыл бұрын

I agree. It’s always good to be mindful of the potential for problems, but having an honest chat with the customer is a must. You can’t be paralyzed by the fear of messing up, although a tiny bit of fear isn’t unhealthy either.

@Local_Boydidgood Жыл бұрын

I find a good detailer is a bit cocky but if they're actually good, I easily allow it. Lee

@jimcorley9051 2 жыл бұрын

What product did you use on the white Gel coat on that old Red / White Bayliner? I have a 1990 Bayliner Avanti 3555. It's Gray and white and the white is being difficult. Jim

@Local_Boydidgood 2 жыл бұрын

I use a DeWalt DWP849X If I'm going for perfection in gelcoat, I don't use a ceramic (unless a very new boat) I prefer the ease, cost and reliability of Fire Glaze by RMP www.restructuremarine.com/fireglaze-products-2 (tell them Lee sent you. No discount and I receive nothing but I'd like them to know 😊) 3M Quick Connect adapter (mfg # 05752) to use with the double-sided compounding pad (3M mfg #05753) or the double-sided polishing pad (3M mfg #05754) Foam compounding pads 3M (05737-discontinued but awesome) or (05723-new version 😑) 3M Super-Duty (05954) 3M Perfect It Heavy Cutting Compound (36102) Perfect-it ex ac compounds by 3M (36060) Meguiar’s (owned by 3M) Flagship Premium Wax (M6332) Pro Polish by Shurehold or 3M's liquid wax with scotchguard. I receive no payment for listing these items. I list them because you guys ask and I just thought I would save some time. Wear protective gear, this stuff can cause cancer and kill you.

@jimcorley9051 2 жыл бұрын

@@Local_Boydidgood I think the product I have been using may be the problem. It is what was Formally Reel Shine now Starke Yacht Care Products. They seemed ok but I will switch to 3M. I was wondering if you had any comments on Starke Products. The sealer or wax seemed to work very good.Thank you so much

@Local_Boydidgood 2 жыл бұрын

I haven't tried any to this point. If you like it, stay with it. I'm not selling anything here.

@laned8418 2 жыл бұрын

I'm having trouble with my 87 formula. It's red and very pink. Where I peeled the old stickers off, exposing the unharmed paint, it's almost like you can feel the difference with your finger, like the paint on the hull wore down. I tried buffing it out with 3m heavy cut and a wool pad with no luck. It cleaned up a bit, but didn't bring any color back. Any advice?

@Local_Boydidgood 2 жыл бұрын

Hi. The decals covered your gelcoat for a long time (although, you said paint and I've seen some painted formulas from that era..) As the rest of the surface was eaten away by boat washes, polishing and time exposed, what was underneath stayed relatively stable and never wore down. You can almost always get the surface difference between where a decal was and the rest of the boat with Heavy Cut by 3M but never really fully even and flush, not on your 1st passes at least. If you buff the boat year after year, that will minimize but some people just want it gone. The best way is to block sand it smooth and then buff it (in my opinion) This will level the surface and while doing so, you might find that the color around the decal's old home, has that color you wanted to see. Sometimes however, on older paint, that's now the color. From '87, at almost 30, it's acceptable to show some age. As to your gelcoat (if it is) You can try Super-Duty to get through the oxidized surface to color and a shine however, Heavy Cut can usually get you there with less mess and just takes a bit longer but finishes much nicer. I apologize, without being there, difficult for me to assess your boat from here. If you were standing near me, I'd say try again, try harder, try longer, make sure you're using a 3M wool pad meant for compounding. www.restructuremarine.com/fireglaze-products-2 (3 year polish) 3M Quick Connect adapter (mfg # 05752) to use with the double-sided compounding pad (3M mfg #05753) or the double-sided polishing pad (3M mfg #05754) 3M Super-Duty (05954) 3M Perfect It Heavy Cutting Compound (36102) Perfect-it ex ac compounds by 3M (36060) Meguiar’s (owned by 3M) Flagship Premium Wax (M6332) Pro Polish by Shurehold or 3M's liquid wax with scotchguard. I receive no payment for listing these items. I list them because you guys ask and I just thought I would save some time. Wear protective gear, this stuff can cause cancer and kill you.

@laned8418 2 жыл бұрын

@@Local_Boydidgood great info, thank you. The stripe decals were towards the top, and im not too concerned about leveling the paint, I was just worried it was maybe worn too thin, but I suppose that's normal. It's just very hard getting any color to come back. I'm gunna try those new 3m pads but am noconvoced it's going to do well. We shall see

@Local_Boydidgood 2 жыл бұрын

I can't tell you how many times I hear this, until a 3M pad is used and then we'll see. I have faith. Most pads out there, even wool, are too soft and gentle. You need a shotgun (analogous usage) Come tell us what you get when you have a decent pad. Good luck.

@sparkyrivera1419 2 жыл бұрын

How long does it stay glossy like that ? Or does it stay like that

@Local_Boydidgood 2 жыл бұрын

An answer can be found in the description along with the linked video to show the results over time.

@offgridwhitetails8768 2 жыл бұрын

Lee I have two spots on a bass boat I am doing that looks oxidized but I’ll be damn if I can get it out. I’ve tried all the way to 600. Stopped afraid I would start to silver the flake. I usually use 3M heavy then perfect it then wax and polish. Any idea what I could try. It’s very noticeable when the rest is glassing out so well. Too bad I couldn’t send a picture.

@Local_Boydidgood 2 жыл бұрын

You can try heavy cut again but this time, spread it out, put your wheel up on an edge and allow it to spin and move either to the right or left (depending on the section) very slowly. Allow the grit to have a moment with the spot. No real pressure, more slow moving and time of wheel on gelcoat. Don't let it spin in one area but move it at a snail's pace across the section and then see if you have a gloss. Sometimes, I cannot get every part to shine either. It sucks. Add decals!? Sorry man, that's all I got from here, blind.

@offgridwhitetails8768 2 жыл бұрын

@@Local_Boydidgood Thanks brother. Yeah what’s weird is one direction you look say from port to nose it looks fine. Look nose to port and it looks like chalk. I went at it again today for a while and nothing. It’s almost like there silver flake was layer down in one direction. Causing somewhat of an optical illusion that it looks faded but isn’t. Lol

@Local_Boydidgood 2 жыл бұрын

You can always try some sand paper. Watch some videos on Wetsanding. I know nothing about the process. Sometimes flake lays in strange ways. I hope you get through it and get to a pretty boat.

@1spittfire 3 ай бұрын

Hello Lee, Just found your video, about to start to polish a boat for the first time i a couple of weeks. Whats the brand of the big pad that you use both sides on? And whats that tool you use to clean the pad before you start? Bregards from Sweden :)

@Local_Boydidgood 3 ай бұрын

Hi, I use a few different kinds. Check out the description for part #'s. The spur is called a "spur tool." You can find them where paint supplies are sold (automobile paint) Good luck.. Lycka till och tack! Lee

@intrinsicfineautofinishing4660 2 жыл бұрын

Interesting what speeds do you use for each step?

@Local_Boydidgood 2 жыл бұрын

Slow or fast, doesn't matter. It works. I go full speed at times just to show off. Slow will deliver a generally better finish than fast.

@texasbackroads4243 Жыл бұрын

What is the name of the compound you used?

@Local_Boydidgood Жыл бұрын

@jeffreysmall5259 2 жыл бұрын

Looking Great 👍 👌 😀 What a difference 👏 👌

@Local_Boydidgood 2 жыл бұрын

And, 2 seasons later, still shiny. Thanks!

@TM-tw1py Жыл бұрын

Fantastic video!

@Local_Boydidgood Жыл бұрын

Audio is screwy but thanks. The rest are better in my opinion. Cheers!

@alexredl2400 2 жыл бұрын

Hi may i ask what 3m compound that was you were useing thanks in advance

@Local_Boydidgood 2 жыл бұрын

www.restructuremarine.com/fireglaze-products-2 3M Quick Connect adapter (mfg # 05752) to use with the double-sided compounding pad (3M mfg #05753) or the double-sided polishing pad (3M mfg #05754) Foam compounding pads 3M (05737-discontinued but awesome) or (05723-new version 😑) 3M Super-Duty (05954) 3M Perfect It Heavy Cutting Compound (36102) Perfect-it ex ac compounds by 3M (36060) Meguiar’s (owned by 3M) Flagship Premium Wax (M6332) Pro Polish by Shurehold or 3M's liquid wax with scotchguard. I receive no payment for listing these items. I list them because you guys ask and I just thought I would save some time. Wear protective gear, this stuff can cause cancer and kill you.

@zx10rmac84 2 жыл бұрын

Nice job matey ✌️🇬🇧

@Local_Boydidgood 2 жыл бұрын

Thanks. I hope you enjoyed.

@roccomicelotta3798 Жыл бұрын

Awesome video thank you for sharing your secret and technique. Ric

@Local_Boydidgood Жыл бұрын

Thanks Ric. I appreciate the kind words. Being fair, the video is kind of raw and has horrible audio. I think it was one of my worst. I have about 300+ more that I think do a better job of showing how all this works. I'm glad you liked this one but my guess is, you'll learn more through some of the other ones. My best, Lee

@NickySull 2 жыл бұрын

So did you just use the heavy, then to the 06085, then just hit it with a bare pad?

@Local_Boydidgood 2 жыл бұрын

Heavy-cut to perfect it ex ac. No bare pads.

@MatthewWebb62024 3 жыл бұрын

Do you think a rotary rather than a DA is a must for this particular situation?

@Local_Boydidgood 3 жыл бұрын

Yes. You'll never, EVER get these results without literally days using a DA or forced rotation. You need a rotary on this level of oxidation. You can finish possibly with a DA but unless you're working with actual sand as the abrasive, they just massage the gelcoat. I need something to get the job done so that I can get to the next boat before the month is gone.

@alexisye 2 жыл бұрын

I just bought an older Key West with pretty heavy oxidization. Going to try this method. Should I peel the old decals off of it or just polish right over them? Thanks!

@Local_Boydidgood 2 жыл бұрын

It all depends on what you want. I pull decals from boats because of a few reasons. Firstly I think people who engineered votes did a really good job at designing the shape and flow of lines that a boat has. And while I admit sometimes some decals seem to accentuate those lines, generally they do it in a very dated and not timely manner. My personal preference is to yank every decal and every emblem off of every boat so that what I'm left with is just a pure canvas of gelcoat that I can polish up. It is specifically in your choice. If however you do find that you remove the decals, just understand that there will be some artifacts of those decals in your gel coat that you will have to grind on to remove. If this is your first time compounding a boat, perhaps we'll leave the details where they are and see if you like the results of the work that you do. If you're happy with those results by all means the next time you do this to your boat hold the decals and have some fun. These are just suggestions it's just what I would do you ask a question and I thought I would answer as honestly as I could. If you need any advice I will be here. Thank you for watching thank you for your question good luck.

@alexisye 2 жыл бұрын

@@Local_Boydidgood Yeah, this is my first go with this, I'll probably just leave them on and see how good I can get it looking. Thanks so much for the reply!

@Local_Boydidgood 2 жыл бұрын

Anytime brother. Good luck.

@marchelanonymous3633 2 жыл бұрын

for beginners,how to start learning like what you did on this video?thank you

@Local_Boydidgood 2 жыл бұрын

Watch more videos (there's like 200+), buy a cheap boat and practice, practice and practice.

@CMDAVISs 2 жыл бұрын

How long will that last ? And what about thick oxidation?

@Local_Boydidgood 2 жыл бұрын

It's still shiny today and that was over 2 years ago. Maintenance is a big part of it but also, getting all the oxidation out to begin with. If it's super thick, try sanding first? kzfaq.info/get/bejne/npujmKZjprW7dWQ.html This was one of the worst boats I've ever done. Sanding would have saved time perhaps but I've also learned a ton since then and have never sanded a boat (outside of removing issues left behind after removing emblems or decals, just to save time) Compound and the right tools and techniques can do everything I need them to. Lee

@sammyvukovic4998 3 ай бұрын

From heavy cut strait to polish and then wax?

@Local_Boydidgood 3 ай бұрын

Watch more of my vids. This was one boat out of millions, they're all different. Lee

@peeinginthewind 2 жыл бұрын

Looks great try foam pads for high speed polishing .. much less change of cutting in swirls 👍

@Local_Boydidgood 2 жыл бұрын

High speed and foam on gelcoat has never been a good thing in my 15+ year experience but I've seen it work well on car paint. There's more than one way to get to glossy. Thanks for the idea.

@peace4peaceful 2 жыл бұрын

So, I'm about to do this on my boat. I bought some cut n polish. Should I use it or no. I'm guessing first sweep cleans scratches. 2nd one finer. Then polish it.

@Local_Boydidgood 2 жыл бұрын

Hi John. The short answers are, yes and no. I hate to sound egocentric but watch a few more of my videos and get a sense of what I do on the regular. The red bayliner vid does not show much and I was crap with the audio so hearing me talk is difficult. I've gotten better. Use a compound with a wool pad on a Rotary machine to get the results you want and then clean the surface, make sure it still looks the same and seal that shine in with a "wax" protection, sealant, polish, glaze... Just something made for gelcoat (no car waxes work for long) I have some long videos, watch 2-3 of them (grab snacks and a drink, they're boring AF) Then, after the basic ideas are underway, ask me anything. Thanks for watching this one though, it's an attention grabber. Lee

@peace4peaceful 2 жыл бұрын

@@Local_Boydidgood thanks Lee. Will do.

@Local_Boydidgood 2 жыл бұрын

Good luck brother..

@ussweeneyd 3 жыл бұрын

Very instructive! Thanks.

@Local_Boydidgood 3 жыл бұрын

Glad you liked it. The last vid (58 minutes) shows more on using compound on small surfaces on the topsides. You might enjoy it. Bring food and a drink, it's long.

@BillyBob-cy9eu 2 жыл бұрын

Sad to think someone would let a boat go to waste like that. It takes someone who can see the potential to bring something so neglected back to its glory. I do cars all the time like this and it pays good. Heck I can make a $1000.00 in a day by just detailing a rig someone was to lazy to take care of. Nice work!

@Local_Boydidgood 2 жыл бұрын

That right there is the power of a good detailer. I agree.

@richardvantrease781 15 күн бұрын

Looks great but would be nice if you told us what u we’re using

@Local_Boydidgood 15 күн бұрын

I agree. Check out any of my other 300 vids, read the description to see what was used and get part numbers. Lee

@caseyjohnson6573 Жыл бұрын

The red paint transfer to the pad is that because you went the through the gel coat and into the base coat?

@Local_Boydidgood Жыл бұрын

No. It took off the oxidized portion of the gelcoat, not paint. There's no paint here. Past the gelcoat is fiberglass mesh and resin. (Bayliner cut some corners early on)

@helpe80 3 жыл бұрын

Hey man if you don’t mind me asking, what speeds do you generally use.

@Local_Boydidgood 3 жыл бұрын

Slow unless you are really good.

@jcarnicella5203 2 жыл бұрын

Have you ever heard of mixing baby oil In with the polish. I’ve never tried it but I know in another video you mention a secret was wondering if that was it or if it’s any good

@Local_Boydidgood 2 жыл бұрын

Dumbest thing I ever saw on youtube. (one of) Not your comment but using baby oil. I've seen transmission oil used too.

@mitchelllewis4916 2 жыл бұрын

Wow! I watched a friend wet sand his 30 year boat and thought, "There's got to be a better way." Thanks for showing me there is before I tackle my 26 year old boat. One question, what is the reasoning of starting at a lower RPM and then going up? Thanks again!

@Local_Boydidgood 2 жыл бұрын

Just stay slow, speed kills. Glad you found this too. Hope it helps.

@tylerrsmith443 Жыл бұрын

This is great! Any tips for bringing back oxidized non skid deck??

@Local_Boydidgood Жыл бұрын

You can use a stiff bristle brush (or a stiff bristle pad for a random orbital buffer), work in an aggressive Cleaner Wax and wipe it off with a microfiber towel or use a gritty rubbing compound and a rotary buffer with a wool pad. Clean and wax with something not so slippery as "wax". Woody's wax and some stuff made for Non-skid would be good choices.

@Local_Boydidgood Жыл бұрын

kzfaq.info/get/bejne/od5gq71ynanLZoE.html kzfaq.info/get/bejne/jMmAdZec3N-bp2Q.html kzfaq.info/get/bejne/oa-ZZqd4lbWyl30.html These vids might help.

@GameDayNation 2 ай бұрын

Wet sanding sounds like an added step that you can pass on, and it is. But that added process will actually save you time in the end. It will also reduce the number of polish pads used and is a for sure process to remove defects & bonded contaminants. Remember NEVER wet sand on flake. Commonly found on bass boats, the sparkling metallic surface should not be wet sanded.

@Local_Boydidgood 2 ай бұрын

Please watch any of my more recent vids. I'm not anti-sanding just, not everyone needs it and it's way too common. Lee

@clarkireland3318 2 жыл бұрын

What a great video! I have a 17 foot 1984 chris craft that I need to put some love on. It's been baking for many years now in the sun. After you cut do you recommend any kind of sealer or protectant?

@clarkireland3318 2 жыл бұрын

Audio was a little challenging....are you applying wax at min 15:00?

@Local_Boydidgood 2 жыл бұрын

I'm not sure when but sure. I have lots of videos that can answer any questions you might have. Grinding gelcoat to submitting is my gig. kzfaq.info/get/bejne/mrCEaKiivZvHkmg.html (just to inspire you) Keep watching my vids, they all cover what I use in some way and how to best protect the boat. Yours requires a lot (not being mean) if it's really dry. Good luck. Thanks for taking the time to watch it.

@Local_Boydidgood 2 жыл бұрын

Meguiar's Flagship liquid wax, 3m's liquid wax with scotchguard, pro polish by Shurehold. In my opinion, the best off the shelf stuff you can buy but you have to watch more of my vids to learn the how and why of when to do things and then, worry about the protecting. This video was a demo, a "proof of concept" for the doubters out there that only sand boats. It wasn't intended to be a "how-to". Watch my longer vids for that or attend a class and go home and kill that CC, make it your boat again. No matter what you do (as not me;bragging a bit) the shine will fade eventually. Old neglected gelcoat hides it's decay deep. Unless you go super deep and pull off all the oxidation, you can expect to do this whole thing again in 6-8 months to a year. Still WAY easier than sanding but, on a 17' boat not terrible if it's your baby. Then, once you have a decent layer of gelcoat to work with, use what I do to polish her to jewel level and keep her looking that way easily with a yearly or every 6 months, wiping her down with a good sealant/wax. Sorry for the short answer earlier. I was driving and shot you a blurb at a fuel station.

@zanaga1901 2 жыл бұрын

What product you use to get rid of oxidation probably work good on a vehicle too I have foam pads and other pads already I rather use my da polisher than the rotary used it again on my truck and it burned through the paint but gonna paint it again this year anyway again.

@zanaga1901 2 жыл бұрын

What kind of wool pad do you use too.

@Local_Boydidgood 2 жыл бұрын

I use a double-sided wool compounding pad by 3m. Either screw in or quick connect. If you read the description, you can usually see in my vids, a list of the crap ai use.

@Local_Boydidgood 2 жыл бұрын

3M Quick Connect adapter (mfg # 05752) to use with the double-sided compounding pad (3M mfg #05753) or the double-sided polishing pad (3M mfg #05754) 3M Super-Duty (05954) 3M Perfect It Heavy Cutting Compound (36102) Perfect-it ex ac compounds by 3M (36060) Meguiar’s (owned by 3M) Flagship Premium Wax (M6332) Pro Polish by Shurehold or 3M's liquid wax with

@72mespo Жыл бұрын

Just amazing results.

@Local_Boydidgood Жыл бұрын

I get lucky sometime., thanks

@72mespo Жыл бұрын

@@Local_Boydidgood lucky scores too

@Local_Boydidgood Жыл бұрын

😁👍🏼

@VIM97 3 жыл бұрын

Nice video....so how do you polish decals ???

@Local_Boydidgood 3 жыл бұрын

Thanks. Depends on the decal. In this video, I just went over them as if they weren't there. Sometimes you mask them off, sometimes you just don't worry about it. Here's a vid (I have plenty more) of me going over decals. kzfaq.info/get/bejne/fNKYkph_xMXTlYU.html

@wardee549 2 жыл бұрын

Hi, I am in Titusville Fl. What is the best way I can almost lol take your class? Any way? Or do I just need to watch all of your videos? If you have an online way I am willing to pay! Please let me know thank you much! Hope to hear from you soon. Thanks for your videos and awesome work!

@Local_Boydidgood 2 жыл бұрын

We connected. 😊

@scottpage4229 2 жыл бұрын

Hey thanks for sharing your video. Wondering if a polish, with a dual action would work and then a ceramic spray wax? Blue bayliner 1994 and the blue is the only part that looks tired. Thanks

@Local_Boydidgood 2 жыл бұрын

No. No and no. Just because the blue is the part you notice, it saw the same sun and life the white did... It's all gelcoat so it probably has no real gloss either. Rotary, compound, clean and then a random orbital or DA and a bespoke boat "wax" ceramics fail on older boats, it's why you can't get a warranty on a coating for one. What you saw was the easiest way to remove/restore faded gelcoat, sorry. If you just want a simple way to fake it, Olive oil rubbed on the boat might make it shine and bring back the color as long as your original plan. You can put a sheen to it with a DA but a glossy finish, worth "protecting" with a "ceramic" (Si02, not really a ceramic coating more like hydrophobic dust left behind after the spray is wiped off) Vinyl wrap your boat and just enjoy it as is would be my suggestion. Or, hire a decent detailer, let them show you your boat again and then use your spray to keep it going for as long as you can before hiring another one or buying what's needed to keep it goin: A buffer, rotary one. www.restructuremarine.com/fireglaze-products-2 3M Quick Connect adapter (mfg # 05752) to use with the double-sided compounding pad (3M mfg #05753) or the double-sided polishing pad (3M mfg #05754) Foam compounding pads 3M (05737-discontinued but awesome) or (05723-new version 😑) 3M Super-Duty (05954) 3M Perfect It Heavy Cutting Compound (36102) Perfect-it ex ac compounds by 3M (36060) Meguiar’s (owned by 3M) Flagship Premium Wax (M6332) Pro Polish by Shurehold or 3M's liquid wax with scotchguard. I receive no payment for listing these items. I list them because you guys ask and I just thought I would save some time. Wear protective gear, this stuff can cause cancer and kill you.

@bajamike9276 Ай бұрын

What is that 2nd bottle 06085 you used? I cant find it in a 3m search. Or rather can you list the 3M products I need starting with Heavy cut? it looks like if I just follow their labels maybe that will work for me? Heavy Cut, Polish, wax all by 3M? Also what do you think of compared to Mequiars I have used before and just bought a few weeks ago but havent applied it yet. Shoulld I just throw it out and go wiith the 3M instead? My boat is heavily oxidized on the side that sits in the sun all the time in the slip. I've waxed by hand in the past and it never retains the gloss, goes to chalk almost instantly.

@Local_Boydidgood Ай бұрын

3M compounds are the best.. They own Meguiar’s... Start with Super-Duty or Heavy Cut. Finish with Perfect-it ex ac and clean/inspect the finish. Apply a marine wax like Flagship (by Meguiar’s) and keep her clean with a "spray detailer" between washes and before/after use.. Auto parts stores sometimes carry Super-Duty. The Meguiar’s compound, either #67 or 91, are super oily and will hide oxidation from you.. kzfaq.info/get/bejne/r7Z5i5yC2N3UXWg.htmlfeature=shared This video was just an "in your face" vid to show what's possible, don't follow what I did here, watch any of the other vids I've done to get a better idea of how this works. Lee

@bajamike9276 Ай бұрын

@@Local_Boydidgood Cool thanks. Ok another question I have is I just got the Makita tool that looks like the yellow one you have. Is there a reason you use it without the handle on? I put the U shaped handle on mine for added security to hold on to, because my boat is in the water in the slip on a lift and I sure dont want to risk dropping it, I think the handle would give me something to hold on to it better.

@Local_Boydidgood Ай бұрын

It gets in the way. It's for car detailers but you can use it if you want, no foul. I wrap the cord around my arm and then if I drop the buffer, the friction of the cord gives me a few extra moments to catch the cord as it falls. Fresh water won't kill one if you dry it, spray it with wd-40 and spin it every few hours to keep it from rusting shut. In salt water.. Buy a new buffer. Boats have lots of places I need to force a buffer. A handle gets in the way in my work. None of my guys used either the side handle or the D-ring or D-loop but it's ok if you do. If you find it in the way, remove it. Lee

@bajamike9276 Ай бұрын

@@Local_Boydidgood Thanks I'll defeintely try the cord around my arm too, thanks.

@Local_Boydidgood Ай бұрын

Anytime.

@geraldwilliams3898 Жыл бұрын

Oh my goodness, thank you so very much I followed your advice and my neighbors couldn't believe it was the same boat. They were taking videos of my polishing up the paint. I only spent maybe an hour with 3M super duty compound and haven't even waxed the boat. I want to send you before and after pics. Thanks again if you are ever in North Carolina please let us know dinner is on us no matter the cost. Wayne

@Local_Boydidgood Жыл бұрын

Glad it helped! There's beer with dinner right?

@geraldwilliams3898 Жыл бұрын

@@Local_Boydidgood I'll drink milk you can have an entire keg if you want. I drank way too much in the Navy.

@Local_Boydidgood Жыл бұрын

My Army days were a bit foggy too brother. Now I might have 2 a day but this week and last, none. I have my addictions but I like milk too! 😂👍🏼

@geraldwilliams3898 Жыл бұрын

@@Local_Boydidgood Right on my first 4 years in Japan I was drinking errday lol. Spent a lot of time up in Camp Zama, ahhhh the good ole days

@Local_Boydidgood Жыл бұрын

If I never have to wake up @ 5am, ever again, I'm glad them days are behind me. It was fun though.

@ChrisFavarolo 2 жыл бұрын

Simply looks tuff a shame that’s just a demo boat 🤣 awesome pro level job

@Local_Boydidgood 2 жыл бұрын

I appreciate your kind words, thanks. Old bayliner usually shine up if they've been left alone for a decade or two. We did have thoughts of flipping her but at the shop, so effective at up selling.

@helpe80 3 жыл бұрын

After watching a lot of your videos I starting working on my extremely oxidated boat. It’s going well thanks to your videos. My question is Should a white gel coat reflect as much as one with color? My boat is completely white so I have nothing to compare it to. I’m figuring without pigment the image won’t reflect as well?

@Local_Boydidgood 3 жыл бұрын

You're correct, dark gelcoat appears to reflect more. It's an illusion. It's one of the reasons I only do correction/perfecting of gelcoat in either a shop with bright lights or in direct sunlight. You can still achieve a high gloss and it should look like wet, white paint when perfect. You won't see the detail in the reflection as much because the white color reflects so much overall light that it washes out the image being reflected. The same level of surface reflectivity exists between white and colored gelcoats but we perceive it differently. When you can see either a dot of a reflection from the sun (a dot not a blob) or color reflected in white gelcoat, you're good. If I can see my face in the reflection, detail in it and the colors of my skin and eyes, I'm pretty much there or good enough for the girls I date anyhow. Glad you're enjoying the vids. It made my day.

@helpe80 3 жыл бұрын

@@Local_Boydidgood thanks so much man for responding, I kept looking and looking for some information on that and couldn’t find anything. Appreciate your videos, by far the best out there!!! You have ignited our love for our boat!!! Thank you!

@Local_Boydidgood 3 жыл бұрын

I'm honored. Tell a friend. I don't get much traffic on the tubes.

@Local_Boydidgood 3 жыл бұрын

kzfaq.info/sun/PL-w8tlEneOZYZhATUNXylgkXTNC1LFQjn

@JasonWasham 3 ай бұрын

Will this work for metal flake gel coats as well?

@Local_Boydidgood 3 ай бұрын

Depending on how much is left. I've heard sanding the surface lightly 1st is best if the flake can be felt with your hand (bumpy and catchy) Do a test spot but it all depends on how much is left to work with. Lee

@davideldredge1293 3 ай бұрын

@@Local_Boydidgood I have a 1988 bassboat with a red metal flake top cap. In the garage, it looks like a million dollars. On a cloudy day, it looks like a million dollars. When I am on the water, it looks like a million dollars until the sun hits it a just the right angle. Then you can see a cloudiness in some areas. Its like the gelcoat has something in it under the surface. I don't feel any flake coming through and I have used lots of different compounds on it including the 3m heavy cut which I read will remove 800 grit scratches. Maybe I am running the wrong speed. What rpm should the wool pad be run on the rotary? Is there a point where wet sanding is the only option or is there something even more aggressive than the 3m heavy?

@Local_Boydidgood 3 ай бұрын

You should use (only because they're the most aggressive) 3M pads. Slow works fine, friction heat isn't required or wanted. Keep updating me. Lee

@gunnarhaldorsen4185 2 жыл бұрын

Really really nice! Thanks a lot!

@Local_Boydidgood 2 жыл бұрын

Thank you a lot. 😊

@carlmaro 2 жыл бұрын

ok, I bought everything, did everything and my 96 cajun bass boat shines like glass. Now, How do I maintain it so I Never have to Heavy cut it again ??

@Local_Boydidgood 2 жыл бұрын

Fists, congrats and, you're welcome. 2nd. I assume you also cleaned it well before waxing it with one of the waxes I suggest in the description. Now, every few months, spray and wipe it with 303 aerospace protectant or a good polymer spray "deataile/wax". Keep the boat clean, don't let water spots form and make sure to cover it when you can. The sun, dirt and the weather can all degrade the protective layer you apply. Don't use a ceramic on a boat older than 2-3 years old.

@carlmaro 2 жыл бұрын

@@Local_Boydidgood I forgot say Thank you. I've tried it All, bought it All. Even used furniture polish ( I know, I know ) But after watching the magic you do with heavy cut. Honestly. She's never looked or felt better. Thanks for all the tips Lee. Keep up the good work. 👍

@Local_Boydidgood 2 жыл бұрын

Lol, that's OK, I'm a dick and reminfmded you. I'm actually really haolppy to hear about your success, seriously. Thanks for letting me know. In all honesty, a badly oxidized boat might get hit once to get it right and then another few times but then you're good if you can keep it up. If done right, you can expect to never use Super-Duty again but you might need heavy cut once or twice and then Perfect-it ex ac but the time between now and then you can keep it going with a spray detailer. They work as stop-gaps and if used before your protection lets go. If you're on top of it, you can avoid buffing her again for years. Most people wait too long between maintenance. Sorry for busting your chops. Lee

@carlmaro 2 жыл бұрын

@@Local_Boydidgood No worries at all, she's a purple and black metal flake. Finish wasn't shot but the top side was oxidized. It took me all of a day, but I'm happy with the results. Thanks and for all the insight.

@Local_Boydidgood 2 жыл бұрын

Anytime brother, any time.

@simonlawson4111 2 жыл бұрын

Hi Lee, I have a boat with red gelcoat and is in the same condition as your training Bayliner, I've currently tried a couple of test areas with a dewalt rotary polisher a wool pad and 3m heavy cut but I don't see the pad turning red as material is removed , any thoughts please. Really enjoy watching your skill and professionalism. Cheers Simon in the UK.

@Local_Boydidgood 2 жыл бұрын

It might not turn red. Look at the surface of the boat and don't worry about the pad. What's the surface look like after heavy cut? Lee

@simonlawson4111 2 жыл бұрын

@@Local_Boydidgood Oxidation has gone but looks like dirty marks in the gel coat under a glazed shine, and is a different colour to the original colour that was behind the outboard .

@Local_Boydidgood 2 жыл бұрын

Do it again. It sounds like you need to go harder. Chances are, your oxidized gelcoat wasn't at all like what you saw in this video. Color changes and you might never see it the same again. Exposed gelcoat Vs what's around an outboard will be different for a few reasons (all time related) Try Super Duty and cleave off the top of the gelcoat. Then try Heavy Cut. You might contact a local detailing company to give you a quote or just let them get you to a place where you can maintain your boat from then on. I can't diagnose your problem from here.

@JB-bb1zw Жыл бұрын

Lee quick question, whats the difference between the heavy cut and super cut? Now on to the peanut gallery, you guys need to observe and listen to this guy, I wanted a wet look new finish on a 23yo cobia when i was finished , so i went down the buy this, buy that route, i bought a polisher, DA, wet sand, multi step compounds, wool, foam and was even thinking about a forced rotation buffer.. then i found lee's video, i originally listened to the morons at west marine pumping their garbage product that didnt work, so I bit the bullet and went for 3m, i was only able to find the 3m super duty locally, clench them cheeks boys and girls its $60 qt, this shit aint cheap, but i already spent over $100 on the worthless shit above from harbor freight and west marine, i just started my boat and lee's technique is working like a charm,, ive got the wet look that i was looking for with less than half the effort. Most of these videos you see on you tube are designed to sell you something, keep that in mind. To me Theres no school like old school, if something works, go with it, theres no need to re invent the wheel, wich is what alot of these videos are trying to do,, im 60yo and was told this a long time a go about business when i first started out in the dive industry,, "Create the Demand and then supply the product" thats exactly what these videos are doing, they try to make you believe their way is the newest, best and only way that works..thats simply not true, Listen to Lee.. oh btw , Im dealing with a south fla boat that heavily oxidized..

@Local_Boydidgood Жыл бұрын

Wow.. Thanks, I'm still smiling. Super-Duty is diesel fuel and gravel that breaks down to a point and then it's just small sand. Heavy Cut has a reducing particle that eventually has a reducing molecule..it'll reduce to almost Perfect-it ex ac. Super-Duty is my shotgun, Heavy Cut is my stiletto and Perfect-it ex ac is a scalpel. My best and thanks again for the "peanut gallery" part, that was cool. Lee

@ericktapia5698 2 жыл бұрын

I’ve been detailing for years. One guy who taught me how to do boats taught me to use a water spray bottle and sprits light over decals. So this tripped me out to see that’s it’s really not needed

@Local_Boydidgood 2 жыл бұрын

Sadly, I see lots of stuff used because someone told someone how to do it. I started out just like you, listening to what people told me but within a few years, I just went my own way. I use 3M compounds in ways they don't even understand. To get Super-Duty to finish to a swirl-free finish Heavy Cut is easier as is Perfect-it ex ac but if you had told me that was possible 13 years ago, I'd have said you were crazy. If I hadn't seen it, I just wouldn't have believed it. I'm just trying to show people, there's more than just what the last generation had going for it. Glad you found this, there's about 200 more vids and some of them might get you to the same spot this one did, opening to new ideas. Thanks for the comment.

@ramoncortes7049 Жыл бұрын

Thank you for sharing all your experience, i been watching your videos for about 2 hrs, can you please tell me the speed that I need to used on the different compounds. Thank you

@Local_Boydidgood Жыл бұрын

Slow. Lento. If you watch enough of my videos, you'll find some where I talk about speeds. Slow works and is safe. If, after some years, you want to go faster because you've learned your skills well, go ahead.

@ramoncortes7049 Жыл бұрын

Will do. Thank you again!!

@Local_Boydidgood Жыл бұрын

Anytime.

@darrenvigee8198 Жыл бұрын

What are the compounds .?

@Local_Boydidgood Жыл бұрын

In the description. Thanks for watching

@cawfeedawg 2 жыл бұрын

ceramic coating on the deck? anyway great video. thanks for sharing your knowledge and experience.

@Local_Boydidgood 2 жыл бұрын

I'm not a fan of ceramics on an older boat at all. I was asked to do it to demonstrate how they fail. Thanks for the comment. My pleasure.

@igotaction 2 жыл бұрын

Hello I was curious what size/brand wool pad you are using?

@Local_Boydidgood 2 жыл бұрын

I use 3m foam, wool or nylon pads, some soft Shurehold DA pads and that's about it. 3M Quick Connect adapter (mfg # 05752) to use with the double-sided compounding pad (3M mfg #05753) or the double-sided polishing pad (3M mfg #05754).

@igotaction 2 жыл бұрын

@@Local_Boydidgood thank you sir for that thorough and informative reply, fantastic work!

@Local_Boydidgood 2 жыл бұрын

Anytime. Thanks for watching.

@igotaction 2 жыл бұрын

@@Local_Boydidgood BTW I've been working on BMW's probably about as long as you've been detailing boats (before the E39 was released), you can look up my name on Instagram if you ever have a question about your E39 you can DM me.

@Local_Boydidgood 2 жыл бұрын

Well, figure out how I can tune the 4.6us motor to accept a twin-screw blower and I'll help you buff stuff! 😝👍🏼 I'm not on anything but bimmerforums.com and here. I don't do social stuff well. 🤪

@HomesteadFishing Жыл бұрын

Looks good :)

@Local_Boydidgood Жыл бұрын

Thanks, it was a fun project. There's 300+ more with similar dramatic impacts, better audio and commentary. Thabjs for watching and saying hi! Lee

@Devast8r34 2 жыл бұрын

I am working on a boat and I feel like the blue is faded I have shine its just not the same colors as under the stickers. What Dewalt are you using?

@Local_Boydidgood 2 жыл бұрын

DWP849X. I've seen this. Try going more aggressive in the earlier passes and really grind on the surface to get down to pigment that hasn't bleached out. Apply the "wax" thicker than normal and let it sit a bit, possibly repeat. Good luck.

@Devast8r34 2 жыл бұрын

@Local boydidgood thank you for the response. I am using a Flex DA with wool how fast do I want be cutting when really pressing into it? Also should I use a deoxidizer at all?

@Local_Boydidgood 2 жыл бұрын

If you have bad, deep oxidation, a DA will be most effective with sandpaper. You can get a rubbing compound on a wool pad and a DA but you'll have to be there for a long time @ high speeds with decent pressure. I feel like you need a rotary or some sanding disks. I hate to toss out a challenge but rotary works harder. Look for one used online. Dewalt, porter cable, makita... A DA can bring back a shine but takes forever to get a glossy mirror like finish with deep oxidation.

@Devast8r34 2 жыл бұрын

@@Local_Boydidgood thank you!!!!

@Devast8r34 2 жыл бұрын

@Local boydidgood the solution for the boat im workin on is it needs to be wet sanded. But I got good practice with the buffer!

@jackjieafa3046 Жыл бұрын

Great job ❤

@Local_Boydidgood Жыл бұрын

Thank you.

@savipv8491 Жыл бұрын

@@Local_Boydidgood what u r using?....sander with what tip?

@Local_Boydidgood Жыл бұрын

There is no "sander". I use a DeWalt DWP849X rotary polisher or buffer or "buff" (if in Australia) If I'm going for perfection in gelcoat, I don't use a ceramic (unless a very new boat) I prefer the ease, cost and reliability of Fire Glaze by RMP www.restructuremarine.com/fireglaze-products-2 (tell them Lee sent you. No discount and I receive nothing but I'd like them to know 😊) 3M Quick Connect adapter (mfg # 05752) to use with the double-sided compounding pad (3M mfg #05753) or the double-sided polishing pad (3M mfg #05754) Foam compounding pads 3M (05737-discontinued but awesome) or (05723-new version 😑) 3M Super-Duty (05954) 3M Perfect It Heavy Cutting Compound (36102) Perfect-it ex ac compounds by 3M (36060) Meguiar’s (owned by 3M) Flagship Premium Wax (M6332) Pro Polish by Shurehold or 3M's liquid wax with scotchguard. I receive no payment for listing these items. I list them because you guys ask and I just thought I would save some time. Wear protective gear, this stuff can cause cancer and kill you.

@albertosanchez6338 2 жыл бұрын

Ill start by saying great work and excellent results thank you for sharing your knowledge I have no experience with gel coat why is the pad with the color of the boat is that normal ?? I appreciate the input

@Local_Boydidgood 2 жыл бұрын

Fairly normal. You're removing gelcoat that's oxidized so, it stays in the pad and gets thrown about off the pad. Thanks for the view/comment and question. As long as it's not horribly dark while being near a white gelcoat, you'll be fine, the cleaning and wax afterwards will remove it. If concerned, tape stuff off with blue masking tape (not frog tape)

@chrisgraham8711 2 жыл бұрын

Watched every second of the video without needing a drink lol. I ordered the Dewalt and the first 3M product but wondering why the switch after the first section ? What's the difference between the first and the 06085 ? Should I choose one over the other depending on my issues ? Or use both ?

@Local_Boydidgood 2 жыл бұрын

Just a demo, I use both because some boats will need either or both. This is just an example of what can be done/expected if either product is used. If you don't know what you'll need? Have both ready to be used. Glad you didn't dehydrate. Typically I use the following: www.restructuremarine.com/fireglaze-products-2 3M Quick Connect adapter (mfg # 05752) to use with the double-sided compounding pad (3M mfg #05753) or the double-sided polishing pad (3M mfg #05754) 3M Super-Duty (05954) 3M Perfect It Heavy Cutting Compound (36102) Perfect-it ex ac compounds by 3M (36060) Meguiar’s (owned by 3M) Flagship Premium Wax (M6332) Pro Polish by Shurehold or 3M's liquid wax with scotchguard. I receive no payment for listing these items. I list them because you guys ask and I just thought I would save some time. Wear protective gear, this stuff can cause cancer and kill you.

@chrisgraham8711 2 жыл бұрын

I just finished watching the 32min Blue Bayliner video and it turned out great. I've never been a fan of wet sanding though I don't understand it all but your method just seems so much more practical plus I'm watching you guys do it without a lot of cut between parts if any. I don't expect your type of outcome as you've got way more experience so if I can just get a 10th of it I would be happy lol. Thanks

@Local_Boydidgood 2 жыл бұрын

I've had 16 year old girls, 72 year old women and men in their upper 70's get this from watching the videos. I get pics and vids a few times a week, from folks who just watched and watched and watched. At some point, the core concept hits you and bam, you're buffing like a champ. Spread, edges, cross-cut your middles and smooth out till almost gone (the compound) and the oxidation. Clean, inspect, lock that shine in. I'm sure you can do it. I have like 200+ vids and many of them are just boring, "here's what I do" vids.

@chrisgraham8711 2 жыл бұрын

I just bought the 05954 from O'REILLYs and have the other two coming from Amazon today, so tell 3M you making them money 💰 hahaha My Dewalt won't be here until tomorrow but I do have a cheap one that I will try just to get this out of my system until then. I just purchased a 21fter that has bad oxidation in red, just like this video. I'm super excited and I will NOT blame anyone if I can't get it looking like yours. I just needed a starting point and like mentioned before, I'm not a wet sand fan.... I wish they allowed you to attach pics on KZfaq comments...... really appreciate your help and have already started sharing your channel

@Local_Boydidgood 2 жыл бұрын

I appreciate that, thanks. I'll be here if you need a pointer. Good idea about posting pics to comments.

@Sambro67 2 жыл бұрын

Thanks brother!

@Local_Boydidgood 2 жыл бұрын

Anytime!

@seanwicks3425 2 жыл бұрын

Dang! That's a whole lot of effort for a Bayliner, and the material to do the work likely cost more than it's worth.

@Local_Boydidgood 2 жыл бұрын

In advertising alone, that boat has made the shop enough money to warrant whatever the material cost was and to have it sitting outside the shop to prove our work in awesome. The point was that almost any boat can be brought back. I know the sound in that video are horrible, I do explain all this in the video. Thanks for the comment.

@wr8010 2 жыл бұрын

After cutting what was the second 3m product finesse ? Have you tried the whole line of 3m gel coat polishing or their wax ? Love the work an the idgaf attitude keep it up

@Local_Boydidgood 2 жыл бұрын

I hate any 2-in-one or a wax added to a cutting agent. It's imporethat the bond between your final protection and the boat be good and strong. Applying a "wax" over a freshly compounded surface, unless squeeky clean to the touch, the polish or wax is mixed with cutting molecules, they're still on the surface, hidden in the wax.. Better to not buy all the 3M line and just use one compound (possibly 2 on bad boats. Here Perfect-it ex ac or heavy-cut followed by Meguiar's Flagship) Thanks very much for the kind words. My pleasure.

@wr8010 2 жыл бұрын

Just making sure I heard and read some of your comments on other vids you take the wax off with fine pad for the supreme shine ? Do you put meguirees on with rotary thanks for reply

@Local_Boydidgood 2 жыл бұрын

I sometimes call Perfect-it, Finess-it. I'm better now but, sorry. I'll apply the wax with a Terry cloth rag typically unless I'm going for an outstanding shine or on dark gelcoat, I'll apply the wax to a soft pad on a dual-action or random orbital buffer. Spread it. Grab a new soft pad and remove it.

@tecnisdaimondm.g9321 Жыл бұрын

Excelente

@Local_Boydidgood Жыл бұрын

Gracias much Hermano!

@david-m-creations799 3 жыл бұрын

Good Job Cleatus..

@Local_Boydidgood 2 жыл бұрын

Thanks?

@goldridgedesign9069 2 жыл бұрын

Bunch of boat in Utah could use this. Killer work looks good.

@Local_Boydidgood 2 жыл бұрын

They all suffer the syndrome. Thanks!

@Local_Boydidgood 2 жыл бұрын

I'm in Beaver today! (almost, driving still) but I plan on being in Beaver for a few days. 😉 Double meanings are awesome!

@quarawlisstafford487 Жыл бұрын

What did you charge?

@Local_Boydidgood Жыл бұрын

Nothing. This is a demo boat to show people that no matter how hard it (the boat) looks, they can come back fairly quickly.

@viperfanatic13 3 жыл бұрын

So, heavy compound. Then perfect it and done? Or finish it off with a finishing wax like maguires flagship? Or a different brand?

@Local_Boydidgood 3 жыл бұрын

I think in that vid, just 1 compound (I forget) if you use any compound the way I do, get a result you like, clean it and any polymer-based product to lock in the shine. All the work (surface finishing) is done with compound, flagship just seals.

@viperfanatic13 3 жыл бұрын

@@Local_Boydidgood less steps sound good to me. Especially at $60 a bottle. Lol Do you have a certain polymer based product you like?

@Local_Boydidgood 3 жыл бұрын

Flagship, Jasper's, pro polish, restructure marine polish, 3m's liquid wax.. I trust them (except Jasper's, too young a product for me to fully trust) there's others out there but these almost always make me smile

@Local_Boydidgood 3 жыл бұрын

@@viperfanatic13 it was Heavy-cut and then perfect-it ac ex, sorry. Lots of boats between then and now. I'm old, and forget the details sometimes.

@Local_Boydidgood 3 жыл бұрын

No compound worth a damn has a sealant built in. Meguiar's #67 claims it does, nope. Call them and confirm for yourself if needed. The sealant/wax/polish used isn't expected to polish anything on my boats. I do it with the compound.

@completeyachtdetailimg 2 жыл бұрын

Your are making it look so easy ! What machine are you using? Da Walt ? And did you run 3m heavy cut and what was the 2nd Polish that you used that went over that decal so great ! Thank you for sharing the knowledge!

@Local_Boydidgood 2 жыл бұрын

Thanks, took me 10 years to figure this out and another 5 to perfect it. Glad you're watching, I appreciate it. 3M Quick Connect adapter (mfg # 05752) to use with the double-sided compounding pad (3M mfg #05753) or the double-sided polishing pad (3M mfg #05754) Dewalt DWP849X Heavy-cut and perfect-it ex ac rubbing compound by 3M I found a way to let the compound, pad and machine do almost all the work. Easier on my old elbows and shoulders. 😊

@8516brian 3 жыл бұрын

Ok Lee. So how much sanding do you actually do, and at what point do you consider it necessary? I’m also interested in your thoughts on machine speed. I know it’s not an exact science, but can you offer any guidelines?

@Local_Boydidgood 3 жыл бұрын

I don't sand. Never have, probably never will. If I ponder sanding, I call my friend Super-duty by 3M and never look back. kzfaq.info/get/bejne/g52dZpBnq8q0kXU.html kzfaq.info/get/bejne/jNJ6dtqE3czWln0.html Is yours worse? These were 2 of the worst from last season. They both still look great. No Sanding. Running slow is as effective as running fast but as I have more boats behind each one I do, I go fast where I can. Swirls love speed. Speed is dangerous for the unfamiliar. I'd stay slow until you feel like you are ready.

@8516brian 3 жыл бұрын

Thanks Lee. I appreciate it.

@Local_Boydidgood 3 жыл бұрын

Anytime. A foam pad can not go fast if you are thinking of using one. Wool can but you need a well balanced pad (no vibration at all) I return 4 pads out if 9 and replace them with better pads if possible. All my pads spin without oscillating. This is how I can compound fast without swirls. If I had a wobbly pad, slow would work and fast would ruin your boat's reflection with swirls. Up until 5 years ago, I went slow and achieved perfection that way. By that time, I'd been buffing for 10 years and feared the speed. Speed only works on flat surfaces, not rounded (smaller surface than the pad (minus 2"- edges hardly ever touch the surface unless you edge the buffer. Basically, the compound uses the weight of the buffer to work. More and you risk swirls and burning, too little and you'll scratch the surface with the grit from the compound. There needs to be something pressing the fibers down onto the boat but not too much.

@8516brian 3 жыл бұрын

That’s a lot of great info. Thanks for taking the time to do that. Your comment about foam pads peaked my interest. My background is auto paint correction, so foam (and microfibre) are it for me. I’m going to start doing some boat work and had hoped to get by (initially anyway) with some heavy cut foam pads paired with a forced rotation DA (Flex 3401), but it looks like I’ll need a rotary as my primary tool. Thanks again Lee.

@Local_Boydidgood 3 жыл бұрын

Gelcoat Boats like wool. Cars and marine paints like foam. Odd I know but it works out that way typically. Too much heat gets built up on gelcoat when really grinding hard w/foam.

@1tom35 2 жыл бұрын

So I read there is a class I can pay for? Where?

@Local_Boydidgood 2 жыл бұрын

Chelan WA. You go home when you can feel confident not before. 2-3 day thing.

@clintsteinacher5559 2 жыл бұрын

I'm late to the party but any idea where I can pick up these products In Canada/Saskatchewan And I'll have to watch again. Blew threw it and not sure of the order of operation. Thanks for the help BTW

@Local_Boydidgood 2 жыл бұрын

It's ok, there's about 200 videos like this in my Playlist marked "boats N stuff" As to where you can locate them.. Sorry man, no clue but the Google machine. I use a DeWalt DWP849X If I'm going for perfection in gelcoat, I don't use a ceramic (unless a very new boat) I prefer the ease, cost and reliability of Fire Glaze by RMP www.restructuremarine.com/fireglaze-products-2 (tell them Lee sent you. No discount and I receive nothing but I'd like them to know 😊) 3M Quick Connect adapter (mfg # 05752) to use with the double-sided compounding pad (3M mfg #05753) or the double-sided polishing pad (3M mfg #05754) Foam compounding pads 3M (05737-discontinued but awesome) or (05723-new version 😑) 3M Super-Duty (05954) 3M Perfect It Heavy Cutting Compound (36102) Perfect-it ex ac compounds by 3M (36060) Meguiar’s (owned by 3M) Flagship Premium Wax (M6332) Pro Polish by Shurehold or 3M's liquid wax with scotchguard. I receive no payment for listing these items. I list them because you guys ask and I just thought I would save some time. Wear protective gear, this stuff can cause cancer and kill you.

@clintsteinacher5559 2 жыл бұрын

Thanks for the reply. Do I use all three of those compounds in that order or just any one of those three that I can get?

@Local_Boydidgood 2 жыл бұрын

Start with Perfect-it ex ac and see if that gets you to where you want to be. If not, Heavy Cut and if not, Super-Duty but if so, follow with Perfect-it ex ac and then clean, inspect and wax.

@clintsteinacher5559 2 жыл бұрын

@@Local_Boydidgood excellent. Thanks for your time. I feel good about this

@Local_Boydidgood 2 жыл бұрын

Well, now, so do I. Good luck. I'm here if you get stuck.

@stevescott5131 2 жыл бұрын

I was wondering if you have time to do my boat. I also live in Washington and would like to have my boat done. I see you do great work.

@Local_Boydidgood 2 жыл бұрын

I appreciate the kind words on the work. Bring her to Chelan and I'm game. I don't drive for work anymore. If you're in the 206 there's a guy over there I like the work of and his work ethic is on point. You can find his contact info in my youtube channel's "about me" section.

@bradmclaughlin9023 Жыл бұрын

@@Local_Boydidgood I couldn't find any info on your company or the one in the 206 in the about me section, are you still in the biz?

@Local_Boydidgood Жыл бұрын

I'm in Chelan.

@MountainousJoe Жыл бұрын

It's been a year. Can you tell us how you did in front of the glass? It looks phenomenal, I am going to give it a try on my, new to me, neglected '83 Beachcraft

@Local_Boydidgood Жыл бұрын

Hi Joseph, Thanks for the kind words. As to the front, I used Heavy Cut followed by Perfect-it ex ac with a wool pad. I then used a window cleaner to remove the compound oils and applied Meguiar's Flagship to the area under the glass. I put it on thick and let it sit till dry.

@MountainousJoe Жыл бұрын

@@Local_BoydidgoodAppreciate you sharing your knowledge. Not many pros respond the way you do on KZfaq. Class act, all the best to you :-)

@Local_Boydidgood Жыл бұрын

Thanks man. I try to help if I can.

@brandonbrown772 3 жыл бұрын

Hey man I’ve got a few questions... I’ve used a few different cutting compounds and polish on my gel coat it will look great or somewhat anyways for a week or so and the oxidation will come right back? I’m not sure why or how but I’m curious lol.. What products did you use in this video?

@Local_Boydidgood 3 жыл бұрын

It doesn't matter what I use. Every boat is different. You can use clay dirt and dust in water (seriously, I've seen it but don't recommend it) on a wheel and remove oxidation. I'd suggest going until the surface looks great after it's cleaned and inspected. Then, use a bespoke marine polish/wax/sealant. Don't use a car wax on a boat. Apply evenly (perhaps thicker this time) let dry (a tad longer) and buff off (slowly) If it fades in a week due to sun (you can see one side looking better, in the shade) then you didn't get the oxidation out and you didn't saturate the gelcoat with wax. I'm not going to be able to diagnose what's going on with your boat from here but it all comes down to getting through the oxidation, not just hiding it with oils in compounds like Menzerna, Meguiar's #67 or 91... Very oily and they hide some stuff. 3m perfect-it AC-Ex is a good compound. Flagship by Meguiar's or 3M's liquid "wax" also last a while. Pics would help. Alwayswithacoke@hotmail.com If a boat is really bad, it can have oxidation throughout the gelcoat layer. If this is the case, paint or a vinyl wrap are Great alternatives to propping up a failing surface.

@brandonbrown772 3 жыл бұрын

I’ll send you some pics tomorrow thank you for the info I’m gonna order some 3M

@Local_Boydidgood 3 жыл бұрын

One more thought: if you compound and like the results, do it again. I do this all the time. I'll think "I got it!" but knowing I've been fooled before, I do another pass and figure I got it then. Gelcoat is a trickster. It isn't like paint or metal, it has phases it goes through from day to day.

@Local_Boydidgood 3 жыл бұрын

What compounds? What polishes?

@brandonbrown772 3 жыл бұрын

@@Local_Boydidgood turtle wax rubbing compound a few different kinds and nu finish on the polish

@TheOne-yc1wt 2 жыл бұрын

Dying laughing at all your replies to "Doesnt last on red"!

@Local_Boydidgood 2 жыл бұрын

😁 I mean, if they're going to talk that shizz, deal with some SHIZZ I say.

@TheOne-yc1wt 2 жыл бұрын

@@Local_Boydidgood Those are facts lol, just because another person failed at their attempt doesnt mean they know what they're talking about

@Local_Boydidgood 2 жыл бұрын

I wish teleporters were a thing. I'd love to show everyone how to do this. I wish I had a better forum to show all this stuff off. Doing little vids on random boats isn't really my "teaching", just showing but if I could write up a manual or make a decent step-by-step, I think people might try it. Then again, as every boat is different, a step-by-step would need to be done for like 30 types/conditions of gelcoat. Glad you enjoy me pushing back. My best, Lee

@davidhausler9612 Жыл бұрын

Hi awesome job. Is the wax used here the fire glaze.

@Local_Boydidgood Жыл бұрын

Initially, no. It is on this boat as a test but in the 1st video of this boat, I think Flagship liquid wax by Meguiar's (owned by 3M) Thanks for the kind words. I think if you look at any of my 300+ other videos to see something better than my detailer thirsthl-trap here. Lee

@davidhausler9612 Жыл бұрын

@@Local_Boydidgood hi. Really enjoying your videos and sharing them with friends. Just wondering what you would suggest to remove silicone residue... under my bump rubbers strip I notice a previous repair put silicone in but was messy.. I have tried surface prep, rubbing alcholol and acetone... but can not get it off.. appreciate you help.

@Local_Boydidgood Жыл бұрын

Hi David. Use a scraper and a knife (carefully) to remove a majority of it and then; Once you're removed most of the silicone use a cloth and some methylated spirits to wipe the remnants off. The methylated spirits act as a solvent in this scenario helping break down the last of the silicone and making it easier to manage and less sticky. It sucks..

@davidhausler9612 Жыл бұрын

@@Local_Boydidgood hey thanks heaps. Boat came out nice. I sent you an email with photos.

@Local_Boydidgood Жыл бұрын

I'm honoted. Thabk you. Tell people about the vids, thabks enough. Lee