I will be sure to make a testing video once I get the keypad

Thank you

As soon as I can order one I will install it program the system and make a test video

@@nics-systems-electric Sounds good!

Can’t remember if it was you but a few people noticed what was coming

Yes

Any open circuit would cause an alarm. When all the doors are closed the panel will see 5.6k ohm resistance and if it sees a closed circuit with no resistance it would be a trouble condition. So if it’s in alarm I don’t think it would see a trouble

But I’m honestly not too sure about much I find it a little confusing because I’m used to fire alarm systems that are normally open circuits

@@nics-systems-electric Yeah, i’m pretty sure that method is for when the installers forget to put it at the end of the line, so they do the one leg trick at the panel to stop it from getting a trouble, and i mean it works... but it will give a trouble on an alarm. probably can do this for a normally closed circuit on an FACP too, but that would be a code violation, whereas security doesn’t really matter as long as the wiring isn’t dangerous lol i don’t understand why they would make it require a resistor at all if it has a normally closed circuit, because if the wiring was cut or damaged, it would be obvious because it would be open... but i guess it could also just be shorted out... so maybe the resistor does have a purpose in the end

@@Aaronproductions yeah I think it’s so if somebody just jump the wiring together before the EOLR there would be a trouble. Because if you shorted out the zone if somebody opened the door or set off the motion detector it would be pointless because the system wouldn’t know if you didn’t have a EOLR

@@nics-systems-electric You can use, and i strongly encourage you to, wire them as normally open zones, on the panel you are using, each zone can be set uniquely, eg the tamper you have is only a N/C switch. You may also opt for dual EOL wiring...watch how you wire the Fire Panel, make sure those outputs are to code before showing that video. so others will know how to do it! If you have questions reach out.

Around 200 Canadian and I bought it from aartech

@@nics-systems-electric nice. In the US it’s around the same price or a little more for me to buy wholesale.

I like them better than Honeywell Vista

@@nics-systems-electric understandable

@@pvh_facp4001yt Mostly because I think keypads from Vista systems are ugly

@@nics-systems-electric i have a 6160rf and it just is odd

@@nics-systems-electric As someone with a Vista system, I completely agree. Honeywell has been selling the same system for well over a decade now and even though it still does its job fine, it looks so outdated now. The DSC Neo series have a very nice modern look to them.

Should be in every emergency light I’ve always thought that they should be like that with a generator system and buildings with lighting control the lights are only on if there’s occupancy so emergency lighting should be the same

@@nics-systems-electric ok great. thanks for the feedback. :)

@@nics-systems-electric if it works on a cheaper emergency light, i am going to be installing it and a motion sensor exit sign combo in my walk in attic where i will make my system test videos once i decide on a good beginners panel.

Would be cool on one of my demo systems but for my real system it wouldn’t make any sense as the fire alarm panel is right beside the front door which I put it there on purpose so we wouldn’t need an annunciator if the fire alarm panel was in a different room not accessible from the outside of the building then I would

@@nics-systems-electric true but it would look cool but i know what you mean. Have a good day

@@980AJ true would look cool

Ours was professional install by our alarm company when our house built we had a caddx alarm system but that one quit working after the dialer went out so upgrade to the dsc alarm system we replaced the smoke detector and keypads now are smaller along smoke detectors

Probably I’ve gotten so many comments and request to have a security system

@@nics-systems-electric you Now need surveillance cameras

@@lcstrainspotter3888 I have 4 Wireless cameras

Haha It doesn’t work yet though still need the keypad