1999 Nissan Frontier XE 2.4L Symptoms - Engine Knock during higher RPM range and lower than usual power.
Пікірлер: 59
@daniellediamond6964 Жыл бұрын
Your video is a blessing! Thank you so much for your trouble shooting skills. I have had trouble with gas guzzling, no pick up, tranny limp problems....put hundreds of home repair dollars into this truck. I really love that you laid it all out for us ❤
@samuelceron60452 жыл бұрын
Thank you very much for the information I have the same a 2.4 engine and I could not find the sensor but thanks to your video I managed it. Many thanks
@jonathansanchez102 жыл бұрын
Thanks man!
@markbottorff34933 жыл бұрын
Great video. Is there a follow up showing the replacement?
@EliTheOBDTech3 жыл бұрын
Sorry bro, I really don't do how to videos.
@otownmusic24092 жыл бұрын
Hi there, did you know where is the crankshaft position sensor? Same engine. Thx.. for this video.
@EliTheOBDTech2 жыл бұрын
It is mounted to the bell housing of the transmission, at the back of the engine. It would be best to access the sensor from the bottom of the truck.
@otownmusic24092 жыл бұрын
Appreciate
@ericlassell2076 Жыл бұрын
What about the throttle position senson???
@EliTheOBDTech Жыл бұрын
Hi Eric, What's your question regarding the TPS?
@luismondragon62863 жыл бұрын
Do you have any info on p1736 I have a 1999 frontier and that code pop out
@EliTheOBDTech3 жыл бұрын
When I get a chance, I'll check that code out.
@luismondragon62863 жыл бұрын
@@EliTheOBDTech thanks
@EliTheOBDTech3 жыл бұрын
@@luismondragon6286 hey Luis, quick question, are you sure that the code is p1736? You sure it's not p1336 or p1776 or p1706?
@EliTheOBDTech3 жыл бұрын
Can't find anything on p1736...
@luismondragon62863 жыл бұрын
@@EliTheOBDTech is supposed to be the transmission sensor but my truck is manual not automatic
@juanperez-og8tf3 жыл бұрын
Excellent information, thanks for the data. I have that American 1999 frontier pickup and I wanted to connect it to the 14-pin "Chinese consult" since it brings that connector in the fuse box and the protocol was not matched. If you happen to know what communication protocol that truck uses, I would appreciate it. I found the scanner you use interesting, if you can give me the name since my English is bad. regards
@EliTheOBDTech3 жыл бұрын
What kind of scantool are you using?
@EliTheOBDTech3 жыл бұрын
Scan Gauge II is the scantool I'm using on my truck.
@EliTheOBDTech3 жыл бұрын
I believe the protocol that the truck uses with 14 pin connector is either DDL 1 or DDL 2.
@juanperez-og8tf3 жыл бұрын
@@EliTheOBDTech Yes, it is what I have investigated, but the interface that I acquired was not communicated, I am reviewing the diagram in the connector to know what happened. because for something it brings the famous gray 14-pin ddl connector. It is a mystery that only knows who programmed and gave life to the system of that truck
@EliTheOBDTech3 жыл бұрын
@@juanperez-og8tf Yea, its weird. So far all the enhanced scantools that I own, are able to communicate with my truck using the 14 pin adapter. Launch x431 Pros Mini, Autel Maxisys 906BT, Autoboss V30, Injectronic CJ4LA and OTC Encore.
@justchris8462 ай бұрын
Just replaced the sensor, how do I clear the code ro pass inspection? The code is still in the computer. thanx!
@EliTheOBDTech2 ай бұрын
By using a scantool or removing the battery negative for atleast 10 mins
@EliTheOBDTech2 ай бұрын
If the code can't get cleared, then your problem is still active. You may have a wiring issue.
@justchris8462 ай бұрын
@@EliTheOBDTech Thank you for responding! It’s the 2000 year model XE, I think the wiring is bad, but i’m gonna disconnect the battery for 10 minutes. If you were in fort worth, I’d pay you to fix it, lol!
@EliTheOBDTech2 ай бұрын
@@justchris846 Yes, distance is always a big factor, lol
@THENATHE. Жыл бұрын
What sensor is that? I am very interested in realtime RPM readout. Thanks!
@EliTheOBDTech Жыл бұрын
Knock sensor
@THENATHE. Жыл бұрын
@@EliTheOBDTech I meant the one on your dash that does the readout for RPM
@EliTheOBDTech Жыл бұрын
@@THENATHE. scan gauge 2.0
@bensalazar57632 жыл бұрын
so if i have a crack like yours is it just a matter of replacing that sensor ?
@EliTheOBDTech2 жыл бұрын
Yes.
@bensalazar57632 жыл бұрын
@@EliTheOBDTech how did you rotate your air filter housing up like that, there is a rubber line on the top left of the housing stopping me from rotating it as you have it, any tips or tricks I should know?
@EliTheOBDTech2 жыл бұрын
@@bensalazar5763 Is it a rubber hose or cable line?
@bensalazar57632 жыл бұрын
@@EliTheOBDTech rubber hose
@EliTheOBDTech2 жыл бұрын
@@bensalazar5763 just loosen the clamp from the hose and hose should rotate.
@rayjimenez3265 Жыл бұрын
Is there more than one knock sensor?
@EliTheOBDTech Жыл бұрын
Four cylinder only has 1. For the 6 cylinder has 2
@Hypnosao2 жыл бұрын
My knock sensor wires were ripped out not by the sensor but wherever the wire leads to could you try and let me know where the wire should lead to or how to figure it out would be great !
@EliTheOBDTech2 жыл бұрын
What year is your truck 🛻?
@EliTheOBDTech2 жыл бұрын
These nissan trucks come with a sub harness that can be bought from dealership or online store. No need to solder wires or splice wires. The sub connector on these d22 trucks are located near the power steering pump.
@Hypnosao2 жыл бұрын
@@EliTheOBDTech 1998 2.4 rwd I’d like to just be able to splice the wires wherever they disconnected from the harness or a plug just not 100% where the wire originally ran
@EliTheOBDTech2 жыл бұрын
@@Hypnosao www.partsgeek.com/gbproducts/WC/8230-01339338.html?YN&PartsGeek+Google+Base&+Frontier+Knock+Sensor+Harness+Original+Equipment+W0133-2282837+98-00+Knock+Sensor+Harness+1999&fp=pp&gbm=a&gclid=CjwKCAiA_omPBhBBEiwAcg7smS4Ml9rpLLSlZG3EiPxv8-9F6xJCuE0X41gb5CaurTdt6mxPizT3khoCoPcQAvD_BwE That's your best option, to be honest.
@EliTheOBDTech2 жыл бұрын
@@Hypnosao can you take a picture and send it to my email address ? Eguillen.tech@hotmail.com