That is very impressive on stock block and internals
@Neomustangs2 жыл бұрын
Ty !
@5.0tussin8 жыл бұрын
What were the 1/8th. mile and '60ft. numbers? Clean running car............
@Neomustangs8 жыл бұрын
6.5s and 1.40 60s
@DUNEATV5 жыл бұрын
You keep posting these videos and I’m going to buy myself another fox body!
@Neomustangs5 жыл бұрын
Yes I will !
@DUNEATV5 жыл бұрын
Neomustangs Gee thx...
@superglx70282 ай бұрын
Is this Thompson?
@codytroyer94742 ай бұрын
Yea
@gonemad3639 жыл бұрын
Im the driver in the vid, its never been on the dyno for power pulls. Only been on there to get the N/A tune close. The rest has been done at the track reading plugs and I have a really nice wideband in the car.
@danielcrmstr11482 жыл бұрын
I know it's an old post, but what air/fuel ratio are you shooting for? Thanks!
@oscarvillarreal89513 жыл бұрын
They say stick is better than Automatic. But benching at 10's with an automatic seems better than stick by this point of view.
@Neomustangs3 жыл бұрын
Racing autos are more consistent yes. Getting a stick on point is a bonus
@oscarvillarreal89513 жыл бұрын
@@Neomustangs yeah, if you mess up on the stick, it's over. The C4 transmission seems pretty good for an automatic though.
@badass6.0powerstroke10 Жыл бұрын
@@oscarvillarreal8951 C-4,s Built Right can take about 1000 hp, All depending on Vehicle Weight too.
@svegt9 жыл бұрын
What transmission great setup and great times
@Neomustangs9 жыл бұрын
svegt C4 trans.
@joemamastinks1611 Жыл бұрын
Very nice, who makes your stall converter?
@jedk95232 жыл бұрын
what all was done? id like to do this to my 1986 ford thunderbird.
@DanielRamirez-nd6ii7 жыл бұрын
Nice stang!!! really really cool
@masimpson869 жыл бұрын
What is the suspension setup on this one? Left pretty nice. Suspension is the next thing on the list for my car, and subframe connectors.... lol.
@Neomustangs9 жыл бұрын
masimpson86 Gonemad363 is the suspension guru for this car. Could probably answer that question a little better. He posted that hes the driver and possession of the car. He and I both own the car equally with parts and such. Its got kmember, rack, coil overs in the front setup for this car. In the rear we welded up the boxes and reinforced them. Mike (Gonemad363) made his own Anti-roll bar which works probably better than you buy and much cheaper. Did quite a few good tastefully done suspension stiffen and tweaks to make this car go straight. Still set up stock location but much stronger, straighter and weight is correct.
@nigelthomas12232 жыл бұрын
Nice what size stall and rear gear
@Neomustangs2 жыл бұрын
355 and 4200
@ScaryTerry2537 жыл бұрын
mustang was awesome. but I kinda want to see whatever that was hitting in the background
@lau123423 жыл бұрын
What kind of fluid you use in the trans? Type F is getting very hard to find here, thinking of equivalents for that..
@Neomustangs3 жыл бұрын
Cheap super tech crap at Walmart
@coachrickvice26438 жыл бұрын
The guy videoing said 200 shot, you say 150 shot. Which was it?
@scrappyclappedoutfoxbody41746 жыл бұрын
I heard 2nd pass 200 shot...
@josephmoneymobley5 жыл бұрын
Could have been faster if he would have gotten up on the stall. Seemed like he left just above idle
@Neomustangs5 жыл бұрын
Nah it was about right. Didn’t have. And stall
@josephmoneymobley5 жыл бұрын
@@Neomustangs well either way its a clean fast fox .
@Neomustangs5 жыл бұрын
THank you!
@mxrider2784 жыл бұрын
What rear end ratio?
@Neomustangs4 жыл бұрын
3.55
@mxrider2784 жыл бұрын
Neomustangs thank you, nice car
@Neomustangs4 жыл бұрын
Thx. And Yw!
@joegarza69874 жыл бұрын
What gets did you use for the 200 shot?
@H00K-KING4 жыл бұрын
Stock ecu? I have a lot of questions about the motor trans set up is there a thread somewhere?
@Neomustangs4 жыл бұрын
Yes
@H00K-KING4 жыл бұрын
@@Neomustangs I've always built sbc and ls motors but want to do something different and go with a 302. What's the motor set up
@@Neomustangs what do you mean by flipped pistons?
@jakelegler80894 жыл бұрын
Neomustangs did you have to cut reliefs into the pistons with your top end setup? I’ve heard about interference issues and want to avoid that. Also is that an early or late explorer intake? Working on my first 302
@stevenhill65028 жыл бұрын
What kinda heads
@Neomustangs8 жыл бұрын
Tfs 170
@troymacleod79446 жыл бұрын
I must be doing something wrong lol my h c I tfs 306 fitech Gemini twin nx max 4 4:10 gear although five speed doesn’t work like this lol
@lookinlost56988 жыл бұрын
how much was he spraying?
@Neomustangs8 жыл бұрын
+Bradley Watkins 150
@coachrickvice26438 жыл бұрын
+Neomustangs 200 shot or 150?
@itstheredwiggler53699 жыл бұрын
What did this setup dyno at?
@wb4h3 жыл бұрын
What do you plan on putting in it once the block splits?
@Neomustangs3 жыл бұрын
The car got a 351 that went into my black hatch after the coupe was sold. Its now a 408 in my white turbo car.