NOCO GENIUS10 Battery Charger Review, In Depth

Рет қаралды 238,531

Күн бұрын

Get Your GENIUS10 ---› www.techbatterysolutions.com/...
This is our full review of the brand new NOCO GENIUS10 Battery Charger and Maintainer 10 amp unit. We cover both the basic and advanced functions of the charger along with a walkthrough demo of how to use the charger and cycle through its modes!
#NOCO, #NOCOGENIUS
NOCO GENIUS10 CHARGER SPECS:
Input Voltage: 120-240 VAC
Output Power: 150W
Charging Current: 10A
Low-Voltage Detection: 1 Volt
Back Current Drain: 0.5mA
Ambient Temperature: -20C to +40C
Battery Voltage Supported: 6V, 12V
Battery Chemistries: Wet, GEL, MF, CA, EFB, AGM, Calcium, Lithium
Battery Capacity - 20AH to 230AH
Housing Protection: IP65
Cooling: Natural Convection
Dimensions LxWxH: 7.1 x 3.6 x 2.3
Weight: 3.33 LBS
We carry the full line of NOCO battery chargers, check them all out!
Get Your NOCO CHARGER Today ---› www.techbatterysolutions.com/...

Пікірлер: 753

@goredknight3017 3 жыл бұрын

Your review was a touch above the rest as you went into the faults and explanation in a clear instructions and nice to see the buttons marked out and a quick and professional explanation on the faults that you may come across. Thanks

@salinsarin1 3 жыл бұрын

One of the best reviews of genius 10.. This actually explains nicely each mode and how to select it & what exactly each mode does.. Very nice for a novice home owner, who wants an all round general purpose battery charger (kids car +my car). Thank you.

@charlesmcgehee3227 3 жыл бұрын

Good review. Note this: some batteries, depending on the capacity and condition, will take up to 48 hours in the maintenance mode, to fully reach 100%. The single green LED will pulse until the DC voltage reaches 15.5 DC. (FACT CHECK THAT) Then the LED will turn solid Green. This is not stated in the directions, but NOCO tech support will "school" you if you are having trouble. I recharged up a standard 585 CCA lead acid battery. It took around 36 hours before the Green light turned solid. To convert the CCA to Ah, multiply the CCA rating by .7 (.725 to be precise.) I have used NOCO products for a few years now. This Genius 10 is a fine unit.

@mr.kaband4345 3 жыл бұрын

Yeah I was wondering about how long it takes even with a 10amp charger it take forever I had disconnected before full charge since I tought it be done is 24 hrs but apparently I was wrong

@ninjazzrhythm400 3 жыл бұрын

Thank you. I was wondering about that pulsing green if it was done.

@mr.kaband4345 3 жыл бұрын

NinJazz Rhythm my 70 amp battery took 4 full days to charge until I got a solid green

@axlef1513 3 жыл бұрын

Thank you for this note. This was very helpful. I thought something might be wrong when after a day the green light has not yet turned solid.

@PouchMaster 2 жыл бұрын

Yeah thanks I was totally wondering about that too! Must be like it really has to slow down from bulking the battery but then it like takes a long time to force that last little bit slowly!

@mr84ttop34 3 жыл бұрын

Thank you for sharing! I just purchased one and received it in the mail today.

@johnadams9044 2 жыл бұрын

This video is far easier to follow and understand that the tiny manual that comes with the charger. Thanks.

@theuncanspan 3 жыл бұрын

You are the best and most comprehensive review of this charger. I gotta buy one.

@62shalaka 8 ай бұрын

I watched this video and bought the Genius10 charger from High-Tech Battery Solutions. Received it early today and it's being used right now. Everything has worked perfectly, so far. The video made understanding and using the charger much easier.

@devildogg112985 6 ай бұрын

Finally a detailed review that was greatly explained in laymen terms. Thank you for the video.

@bmm760036 3 жыл бұрын

I think you meant it is the ‘successor’ to the G7200 series as opposed to the ‘predecessor’, but otherwise a good review of this product.

@michaellombardo8985 4 жыл бұрын

Great video, thanks for sharing!

@logicfirst7959 4 жыл бұрын

exceptional review - concise and to the point - keep it up

@CB-ee1fh 3 жыл бұрын

Thanks for the video. They should hire you to write their manuals! The manual as written really falls short and your video was great.

@benmoen 2 жыл бұрын

Man, I really appreciate this review. The user manual is very vague and quite useless and I've had trouble figuring the charger out - then I found this. Thank You!

@JoeBarronTV 3 жыл бұрын

Great job very thorough and to the point. Great job

@waa2100 Жыл бұрын

Best review so far. Thank you sir

@Retaile23 8 ай бұрын

Very clear and concise overview.

@MrHanowski 2 жыл бұрын

Excellent review. Well done!

@ImASurvivorNThriver 2 жыл бұрын

Great review! Thanks for sharing.

@felixvikes28 4 ай бұрын

Thank you appreciate your detailed review. I got one of these from a friend without instructions

@cziasai Жыл бұрын

Perfect for what I needed. Thanks

@ThatFreelance 4 жыл бұрын

Fantastic review.

@texaswhitetails1695 5 ай бұрын

Great video man,thanks

@carlosezepeda-gq8pr 18 күн бұрын

Feeling good, I received my today and is awesome 😊😊

@DocHoliday-to6kp 5 ай бұрын

Great Review. Thanks

@glasperwashington3300 9 ай бұрын

Yeah man, you know your product, awesome awesome review!

@Shanester66 4 жыл бұрын

Is it every necessary to use repair mode on a 12v AGM battery? If so, should you use it every so often as a maintenance tool?

@roryorbit 2 жыл бұрын

Very good video. Very informative and clearly explained. One thing you could add is the different ways the 4 charging lights(red red orange and green) behave in different scenarios relating to the charging process. I’ve noticed with the batteries I’ve been charging over the last few days that the solid green is really the only one that signifies that a battery is actually fully charged, would this be correct?

@HighTechBatterySolutionsInc 2 жыл бұрын

Yes that is correct, the solid green LED will indicate your at 100% state of charge.

@Twobarpsi Жыл бұрын

Good review!

@Twobarpsi 11 ай бұрын

Just got this charger today!

@josemedeiros007 6 ай бұрын

Great review, what is your opinion on Pulsetech PowerPulse passive desulfators?

@me.6737 2 жыл бұрын

Thanks for the informative review, do you happen to know what the output is in supply mode? I.e would be suitable for when reflashing/coding ecu's? Thanks.

@HighTechBatterySolutionsInc 2 жыл бұрын

The output for the supply mode is listed as: 13.6V @ 25°C | 10A | Max 12A. I have never tried reflashing with this charger

@dwinesett 2 жыл бұрын

Great video- thank you for the information. Couple of questions: Can this be connected to two 12V AGM batteries connected in parallel arrangement? If so, do you connect to the + terminal on one batter and - on the other?

@HighTechBatterySolutionsInc 2 жыл бұрын

Yes, you can connect this charger to a pair of 12V batteries wired un in parallel without an issue. You can place the charger clamps on the posts of the very first battery. You would split the clamps between the two batteries if they were wired up in series, no need to do this in parallel as the charge will flow from the first to the second without an issue.

@vrod1a 3 жыл бұрын

Thanks for the review 👍 In the detail description of charger it states that it can charge deep cycle battery, What setting should I use for charging deep cycle battery ?

@HighTechBatterySolutionsInc 3 жыл бұрын

For deep-cycle batteries, you will not have to select a special setting other than the correct battery chemistry mode.

@Need2Build 2 жыл бұрын

Thanks for the informative settings. Can this be used all year round to maintain our AGM batteries on the ‘12agm’ setting? (Also aware of the 2D)

@HighTechBatterySolutionsInc 2 жыл бұрын

Yes, this charger can be left in the 12V AGM mode all year round to maintain an AGM battery without worry.

@etcetc6307 3 жыл бұрын

Thanks for all the explanations. Can repair mode be used on an AGM battery? I keep getting Battery Not Hold Charge error. Should I try the Repair mode? Thx.

@HighTechBatterySolutionsInc 3 жыл бұрын

If you keep getting the No Hold Charge error then you have nothing to lose by trying the repair mode. If it errors out in the repair mode then your looking at more than just capacity loss as an issue with the battery. I always recommend the repair mode be used only necessary with AGM series batteries. The reason being is that the repair mode can cause gassing in the battery and as you know with a sealed AGM series - you can't replace that lost water.

@doctorwanchai1 3 жыл бұрын

The pros of this new model year are every all car and bike battery types chargeable, the cons is the NOCO connectors is very hot the result is charging voltage is lower than described for example the charging voltage for AMG battery is only 14.1 Volts lower than 14.7 Volts as described. This is the event that I had monitored to charging voltage graph . I had replaced the connectors with Anderson power pole connectors and charging cables with the thicker cables.

@sierramoon 3 жыл бұрын

Helpful video! I'm charging up a Marine/RV deep cycle battery. If I want to put it on trickle charge for this or any other battery, how would I do that? Thank you

@HighTechBatterySolutionsInc 3 жыл бұрын

The trickle charge mode is built into the last stage of all the charging programs on the charger. All that you would have to do is select the correct charge mode for your battery and then leave the charger to do its thing. Once the battery is fully charged it will then go into its float maintenance mode.

@allenmaner6616 4 жыл бұрын

So if I understand you charge a gel battery in 12 volt mode not agm mold am I correct? Thanks for your review .

@HighTechBatterySolutionsInc 4 жыл бұрын

Correct, if you're going to charge a GEL battery you want to stay on the standard 12V setting.

@sirkildalot8409 4 жыл бұрын

I just bought one of these as I have a deeply discharged battery and I wanted a charger with the force mode. To begin with however I just wanted to charge a standard 12v car battery. When I plugged it in I expected a steady progression through the charge level indicators from one red block through to the full bar (two reds, an orange and a green). What actually happens is the first red blinks for a while, then the first goes solid and the second blinks a coup,e of times then it goes down to no lights then, after a while it goes up to the Amber for one pulse then back to nothing. It doesn’t seem to progress through the bars but seems to be going up and back down? Is it charging? Is the battery OK? Why don’t the instructions tell you what to expect and what the changing lights mean?

@HighTechBatterySolutionsInc 4 жыл бұрын

Leave it connected, it sounds like you have an issue with your battery - possibly that it's not retaining the charge. The charger will error out if the battery is not recoverable.

@johntrenfield8214 4 жыл бұрын

Hi,I’ve just used this device to recharge a new deep cycle marine battery, which I bought a couple of months ago, but haven’t yet put into use. Is it to be expected that it would have run down to less than 25% charged in that time, and how could I tell if I needed to employ the repair mode?Thank you.

@HighTechBatterySolutionsInc 4 жыл бұрын

Deep cycle batteries will lose a % of their charge every day when sitting idle, so depending on how long it sat it's certainly possible. Since the battery is so new I would not worry about using the repair mode. This is for batteries that are on the older side and heavily sulfated.

@olympiawashdrummer Жыл бұрын

I ve been using the 3500 to trickle. The marine battery I have is just over 1 year old and used twice. I got lazy with the trickle maintenance and now the 3500 has that triangle yellow exclamation point when I try to use it. Would this one you demo help this battery situation?

@Richard5873 4 жыл бұрын

Great video lots of information on !! Who sells this currently and basic price ?

@HighTechBatterySolutionsInc 4 жыл бұрын

The NOCO GENIUS10 unit is $99.95 and ships free - www.techbatterysolutions.com/noco-genius10-battery-charger-and-maintainer-10-amp

@alexmah6459 Жыл бұрын

Hi there, a quick question. If the battery in my car is drained, will I be able to connect the Noco Genius10 and have it charge the battery back to full, then start up my car? I mean without taking the battery out of the car? Or would that work at all?

@gregpeters8339 3 жыл бұрын

Great review, thanks. If I have the Noco 10 charging/maintaining a battery and there is a power disruption, will I need to restart the Noco 10 (i.e. set it for 12 v battery) or will it just continue charging/maintaining the battery when the power goes back on.

@HighTechBatterySolutionsInc 3 жыл бұрын

The entire GENIUS charger line will remember the mode it was on prior to a power outage and start back up automatically once the power is restored.

@gregpeters8339 3 жыл бұрын

@@HighTechBatterySolutionsInc Great! Thank you for responding so quickly.

@darylchenoweth9057 4 жыл бұрын

Haven’t made my purchase yet. Perhaps it’s clear to everyone but me but I have a question related to the Genius 10. When charging a 12 V battery do I always have to select “repair” mode when I start charging (or does routine charging begin after simply selecting “type” of battery)? Is “repair” mode ONLY selected when reconditioning a battery is necessary?

@HighTechBatterySolutionsInc 4 жыл бұрын

You would only select repair mode if you know the battery is sulfated. When you're going to charge a 12V battery you would start by selecting the proper battery type - you do not have to select repair mode to begin charging any battery.

@todivetoday 4 жыл бұрын

Thank you

@hudson5573 Жыл бұрын

Great video! QUESTION: Mine just arrived my wife hasn't been driving her car so it sits for a week or more at a time. Should I run the charge mode first, or the repair most first?

@HighTechBatterySolutionsInc Жыл бұрын

I recommend running the standard charge mode on the unit, I only recommend hitting the repair mode if your having any starting issues or capacity issues with the battery.

@bishopgeorge1333 4 жыл бұрын

Great video, do you have to plug it in an outlet so it will work, the reason why I ask when my RV battery go dead for the winter and when I go out to my storage was the RV is store I don't have any outlet to plug it into to power up.

@HighTechBatterySolutionsInc 4 жыл бұрын

Yes, you have to plug the charger into the wall in order for it begin charging.

@rodneyjenkins5538 3 жыл бұрын

What is a good jump start charger that don't need to be plugged in

@forrest42 2 жыл бұрын

You guys always give the most thorough reviews! Looks good! Can I charge two 6v 220ah batteries in parallel with this charger?

@HighTechBatterySolutionsInc 2 жыл бұрын

Yes, switching the charger into its 6V mode will allow you to charge both batteries wired up in parallel without an issue.

@forrest42 2 жыл бұрын

@@HighTechBatterySolutionsInc but both batteries wired in parallel make 12v. Would I need to use the 12v mode to charge in parallel?

@HighTechBatterySolutionsInc 2 жыл бұрын

@@forrest42 If both batteries are wired in parallel you would essentially have a large 6V battery. If they are wired in series then you would have a single 12V battery. Parallel keeps the voltage the same but increases the capacity, series increases the voltage but the capacity will remain the same.

@HighTechBatterySolutionsInc 2 жыл бұрын

@@forrest42 No problem, if you are wiring them up in series then your going to be in the 12V mode.

@forrest42 2 жыл бұрын

I have two 6v 220 amp hour deep cycle batteries that I wanted to wire together to make 12V for my camper. If I'm understanding correctly, wiring in parallel would make 12V and still only 220ah, and wired In series would be 6v 440ah? Thank you So much for the help, I want to make sure I buy the right charger.

@Goooooodnight 3 жыл бұрын

I love the review. Can you use the Force mode to fast charge a battery, say when you are needing to start a car quickly?

@HighTechBatterySolutionsInc 3 жыл бұрын

I personally have not tried this, it may work if you let the force mode run for the full 5 minutes but the output may not be high enough to jump-start the car in a short period of charging time.

@Goooooodnight 3 жыл бұрын

@@HighTechBatterySolutionsInc thanks for the response, even without it, it seems like one of the best chargers for its options and price.

@rickkoehler4426 3 жыл бұрын

My son give me the Noco Genius 10. I have a 2019 Camaro SS. Planning to store it for the winter months, at least three to four months. How do I use this charger to keep my battery charged? Great video, by the way.

@slickrickdarula9483 3 жыл бұрын

Did you end up getting this charger just wondering because I have a 2016 SS Camaro that I store for the Winter I had a CTech charger but it burned up so I'm looking in to one of these noco's

@albertlin4348 4 жыл бұрын

The pictures in the manual suggest when it's at full charge, the first 3 orange lights are off. Is that correct? Also, as soon as it hits full charge, it'll probably go into maintenance mode right away. I don't think we'll ever see the solid green at all. I've been charging my 12V 60Ah car battery since last night and 12+ hours later, I'm looking at 3 solid orange and pulsing green. Just hoping this is the expected behavior and it's in maintenance mode.

@HighTechBatterySolutionsInc 4 жыл бұрын

Let the charger continue through its charging process - you will see the solid green when it's done. When the light is solid green then it hit its maintenance mode and charge as needed.

@benjiechan1 3 жыл бұрын

Can you do.a.video how to use the supply mode pls ?

@leonemclay 7 ай бұрын

You know, when to turn the self facing mode on whether it's dead or churged. What does it mean when you have a green and red light flashing back-and-forth?

@chuckhardie2223 3 жыл бұрын

Does this maintainer shut off when maintaining a battery stored attached to vehicle when battery doesn't need more tricle charge

@musterseeds1778 10 ай бұрын

How long it takes to charge the battery... Can you use this unit to charge your jumping start like GB70 Unite...

@mistersai4340 5 ай бұрын

great review.. maybe the product i need.. can i leave it charging my car battery overnyt on a -40 weather? im having a problems with my car starting it in the morning…

@HighTechBatterySolutionsInc 5 ай бұрын

Unfortunately not, the operating temperature for this unit is -4F. The lowest operating threshold for a charger that we are knowledgeable on is the CTEK MUS 4.3 Polar model which can operate in -22F. www.techbatterysolutions.com/ctek-mus-4-3-polar-battery-charger-56-958/

@Okie-Tom 4 жыл бұрын

For a smaller Agm battery, will the Genius 10 charge it too fast or will it do fine! I want to be able to use it on my big car batteries to top off their batteries every month or so in the winter. Thanks, Tom

@HighTechBatterySolutionsInc 4 жыл бұрын

It will charge batteries over 20 AH without an issue, if you have anything smaller then I recommend stepping down to the NOCO GENIUS5 series.

@Eaton332 3 жыл бұрын

Can I use the Genius 10 to charge my two 6v hooked up in series as a 12volt, or do I need to unhook the 6V batteries and charge them single as 6v?

@HighTechBatterySolutionsInc 3 жыл бұрын

You can leave them connected in series and charge them a single 12V without an issue.

@Eaton332 3 жыл бұрын

Can I leave this on the battery all winter long as a maintainer? I'm about to winterize my trailer and want to set the batteries (2-6Volt in series) on the genius 10--set--and forget--until March. What do you think? Is that a realistic expectations?

@HighTechBatterySolutionsInc 3 жыл бұрын

Yes you can, ensure your charger is on the 12V mode and connected properly to charge both batteries and your good to go.

@FOXbody81 9 ай бұрын

Thanks for great video , I have a question. I have a NOCO GENIUS10 repair mod. Can I use it for agm car battery?

@HighTechBatterySolutionsInc 9 ай бұрын

Yes, you can use it on an AGM battery. I do not recommend using it often on an AGM however, only when its needed as repeated usage of the recovery mode can damage an AGM battery.

@Jimmy_Cavallo Жыл бұрын

💥 Are you familiar with the Genius 1 and how different the two are? Excellent video 🤟🏼

@HighTechBatterySolutionsInc Жыл бұрын

The NOCO GENIUS1 will not have all of the features available on the GENIUS10 model. Besides the 1A output of the GENIUS1, the unit will not have the supply mode or dedicated repair mode. It will however still have the zero volts charging mode, dual voltage capability, and sulfation detection and mitigation as part of its charging algorithm.

@ikramnanlawala4843 Жыл бұрын

Let me start by saying I'm trying to learn a bit here. What would have happened if you stayed in 6V? As for the repair mode, is there an indicator on the NOCO that tells you repair is needed or do you just set it and see if it goes into repair mode?

@HighTechBatterySolutionsInc Жыл бұрын

If you were to put the charger in the 6V mode on a 12V battery it would error out letting you know that the voltage selected is incorrect. As for the repair mode there is no indicator on the charger that says its time to hit the repair mode. You will have to make that call based on the situation - for example if the battery was sitting discharged for a long period of time, or if you notice an overall lack in capacity of the battery and want to try to recover it.

@andrewloza 2 жыл бұрын

thank you.

@nfinnnn 4 жыл бұрын

Hi, thanks for the video. Why don’t these new chargers show on the NOCO website?

@HighTechBatterySolutionsInc 4 жыл бұрын

We honestly don't know when they will put these new units up on their site

@dandettmann595 4 жыл бұрын

@@HighTechBatterySolutionsInc And here's all 4 of their new Genius series. It also includes some estimated charging time charts based on different size batteries at 50% discharge. So I have a question for you and probably have more after I get my charger. Unfortunately I have the Genius5 on the way (5amp) only to find out the boat I bought has a 114 AH deep cycle 12 v which could handle the Genius10 you reviewed and would have cut my recharging time in half. Bummer! Oh well... So do I charge the deep cycle 12 v battery in the "normal" 12 volt mode? Thanks! I don't think they've been on their website very long. Here ya go> no.co/products/charging/multipurpose

@HighTechBatterySolutionsInc 4 жыл бұрын

@@dandettmann595 If your batteries are flooded then yes you will be charging on the 12V normal mode. If your running sealed AGM series in there then you're going to be using the AGM mode.

@MapleMarmite Жыл бұрын

Nice review. What voltage does the charger allow the battery to drop to before it kicks in and starts charging again? I had mine get my battery up to about 14V and when I checked on it a couple of weeks later it had dropped to 12.5(ish)V and the green light was solid, indicating full charge still. I switched the charger off and on again and it started the charging process and had the battery back up to 13V in a few minutes. Is there an issue? Battery only a few months old. Thanks.

@HighTechBatterySolutionsInc Жыл бұрын

I ran your question by NOCO, here is their official response: It sounds like the battery may not be holding a good resting voltage, and the charger may be timing out. The maintenance trickle charge should start when the voltage drops below 12.7V, and the LED should be pulsing green. If the battery is not holding a good resting voltage, the charger will timeout and stop applying the charge to prevent overcharging the battery. If the voltage drops below 12.4V the charger will start the full charge over.

@MapleMarmite Жыл бұрын

Thanks for getting back to me - I’ll double check the voltages during the same situation again to see if I can pin point any issues.

@kevusmc22 3 жыл бұрын

So would you use the 12v repair option on a battery that keeps dying? Hard winter didn’t drive the truck much, but ever have to jump start repeatedly

@HighTechBatterySolutionsInc 3 жыл бұрын

Yes, it may help the battery retain more of its charge if the issue is due to sulfating or acid stratification. If its due the battery plates decomposing or being otherwise compromised then its going to be time for a new battery.

@defenderovich1898 11 ай бұрын

Great review! Will the Noco Genuis10 adjust the charge amperage automatically according to the charged battery characteristics?

@HighTechBatterySolutionsInc 11 ай бұрын

The GENIUS10 unit will taper off its bulk charge rate as the battery nears the fully charged point and continue to lessen the charge until the battery is fully charged. Its the last 10% thats considered the finishing charge in which the charger is ramping down from its bulk charge mode.

@defenderovich1898 11 ай бұрын

@@HighTechBatterySolutionsInc Thank you!

@tomcross9967 4 жыл бұрын

Hi thanks for the video could you tell me do I have to disconnect the battery to use repair mode

@HighTechBatterySolutionsInc 4 жыл бұрын

Good question, I'm not 100% sure on this so I would recommend only using the manual repair mode on batteries that are disconnected from the vehicle. The problem is a lot of the newer cars have computer systems built in that I would assume could be affected by high voltage spikes - better to play it safe than sorry.

@charlesmcgehee3227 3 жыл бұрын

Before plugging in the A.C. plug, put on the battery clamps. Then plug in the A.C. Put the unit into the Repair mode. The red LED will flash on and off. for around 4 hours and then the unit automatically switches out of the Repair mode. However, if the battery is too badly damaged, the Repair mode will end early. Not all batteries can be "Repaired".

@russianwolfhound1 3 жыл бұрын

Informative review. You mentioned the Genius 10 is the successor to the 7200 line. How would you rate the Genius 10 in comparison to the Genius 7200 ? Which is the superior product ?

@HighTechBatterySolutionsInc 3 жыл бұрын

The GENIUS10 is certainly a step above the G7200 in terms of charging modes and power output. The charger has battery diagnostics right on the faceplate and low voltage detection down to 1V (used to be 4V) which we see as a huge plus. The only thing that was a bummer for us is that the G7200 was capable of charging both 12/24V batteries - the GENIUS10 series stepped that down to 6V/12V. Very few people would actually need the 24V mode which is why they dropped it from the model but there was a small market for it that we had to shift to a more expensive model.

@russianwolfhound1 3 жыл бұрын

@@HighTechBatterySolutionsInc Thanks so much for the prompt and very detailed reply. Much appreciated. Cheers !

@derrickmoodie 2 жыл бұрын

Question: I have a couple of dirt bikes with fairly small 12v batteries (6ah). Will this charger sense the smaller battery and reduce amp levels or am I better to use a Noco Genius 5 on these smaller batteries?

@scottwheaton9689 Жыл бұрын

Use the noco 5 for smaller bike/arc batteries that could still be a bit large for a small am battery.

@user-rl3tz5pr5w 4 ай бұрын

Great review, I just got one and wanted to know if you charge your 12v battery and just leave it hooked up does it then work as a trickle charger ??

@HighTechBatterySolutionsInc 4 ай бұрын

Yes, once the charger has brought the battery up to fully charged it will then go into its maintenance mode automatically.

@FreeClimbersNet Ай бұрын

A follow on, as I am using it now on some old agm's: When will you know when charging is completed? I've had one on my noco10 for about 5 hours and the green light just keeps pulsing slowly. When it switches to maintenance mode, does the color ribbon do something differently, essentially telling you when best effort charging is completed?

@SteveHartmanVideos 3 жыл бұрын

do these chargers also act as tenders, can I leave it connected to my battery all winter to keep it healthy, or do I need a dedicated tender?

@HighTechBatterySolutionsInc 3 жыл бұрын

Yes, these chargers will kick into maintenance mode once the battery is fully charged and can be left connected all winter without an issue

@98XC1 4 ай бұрын

Is it safe for car electronics and for the unit itself, to leave it ON in a charging mode while working on a car(ignition ON engine OFF type scenario during reprograming or troubleshooting electrical issue) thank you for review.

@HighTechBatterySolutionsInc 4 ай бұрын

This is a perfect time to use the dedicated supply mode of the charger - its designed specifically for this scenario.

@fullsleevetats 4 жыл бұрын

At the beginning of the video, you said the Genius 10 is the predecessor of the 7200 series. I think you meant the opposite. The 7200 series is the predecessor to the Genius 10 series.

@HighTechBatterySolutionsInc 4 жыл бұрын

Yup, a few people have pointed this out!

@sc010031 2 жыл бұрын

hi, I just purchased this. Can you tell me how long the device needs to be plugged in to fully charge it? How will I know? Thank you I know it is a basic question.

@HighTechBatterySolutionsInc 2 жыл бұрын

Just to clarify, this is a AC operated battery charger. It does not have an internal battery that can be charged up, it must be plugged into an AC outlet in order to function.

@DrewNewmanAce 3 жыл бұрын

What does the genius10 have over the genius5 apart from higher amps and 12v supply mode?

@babagandu Жыл бұрын

Which to get ?? 5 vs 10 amp

@DrewNewmanAce Жыл бұрын

I ended up just buying the 5, it works ok. Haven’t tried the 10

@atreeesboray 4 жыл бұрын

will this noco charger charges deep cycle marine batteries as well as car battery? thank you so much

@HighTechBatterySolutionsInc 4 жыл бұрын

Yes, this charger is able to handle batteries up to 230AH worth of capacity!

@unclelala4216 Жыл бұрын

Thanks for answering my last question but I have another one... I have a 2021 Ram 3500 diesel with 2 batteries , Could I use the Genius10 to charge my 2 truck batteries using the rear 7 pin trailer connector in the rear of the truck. It would be easier access for me. I've heard rumors it can be done but I can't find anything on how to go about it. Any suggestion would be very much appreciated.

@HighTechBatterySolutionsInc Жыл бұрын

Unfortunately that I have no experience with, I'm not sure its possible.

@robertallen7186 3 жыл бұрын

Can I use this unit to charge two 6V golf cart batteries wired in series? I am planning on purchasing the batteries new. Thank you. Bob from Grand Rapids, MI

@HighTechBatterySolutionsInc 3 жыл бұрын

Yes, you can do this without an issue!

@andrewballerini2503 3 жыл бұрын

when it switches to maintenance does it still charge at 10 amps? If so is that bad for battery life? my use is for a trolling motor 1 -4 times per month the rest of time on charger. suggestions should I use the 10 amp to charge after battery use and a 1 amp charger to maintain?

@HighTechBatterySolutionsInc 3 жыл бұрын

The GENIUS10 unit will only hit the battery with the full 10 amp charge in the bulk charge mode. This is in the 25% up to the 75% charge level indicated on the charger. After that it begins stepping the charge rate down as the battery gets closer to 100% fully charged. In the maintenance mode your right around an amp on the battery.

@michaelmeditz1447 2 жыл бұрын

Question. I have a 6 volt battery in a positive ground car (ground cable on positive post to engine block and starter cable to negative post). When charging with this charger - I would still hook up clamps neg-neg and pos-pos right? Is it even necessary to remove car cables off battery before I hook up this trickle charger? Just don’t want to damage anything such as starter or battery.

@HighTechBatterySolutionsInc 2 жыл бұрын

You are correct, you're still going to be connecting the charger positive to positive and negative to negative. You will want to connect the charger directly to the terminals of the battery, and there is no need to disconnect the battery from the vehicle during charging.

@globaljob8689 4 жыл бұрын

I have a fiamm batt that have not intensive used at all prior and has been sitting around untouch for 6Years. I’ve recovered to 12v but after using it for a few connections with a dc ac pure Snr wave inverter, it went below 9v. I did not recharge it for a while but when I tried, it was not able to charge up normally. No obvious bloating but now I can’t bring it back to life. Now it reads 0-1v. I’m contemplating to buy NocoG10. Will it able to force it back to 12v even without refreshing it with Epsom salt?

@HighTechBatterySolutionsInc 3 жыл бұрын

The recondition mode of the GENIUS10 will be able to recover a portion of the capacity of the battery however 6 years untouched is a very long time. If the plates have physically deteriorated then even attempting to refresh the battery would not yield any results as the total active surface area available to produce energy has been permanently reduced.

@montana9703 3 жыл бұрын

this went right over my head...so, quick question. I opened the box, plugged it in for three days. Nothing changed on the lights to indicate it was full. I suppose I'm old school. I need to put a charge on my car that has been sitting for a few months...someone told me to put it on a slow charge for a few days to get it back working as the battery is only a yr old. Help please....

@HighTechBatterySolutionsInc 3 жыл бұрын

Did you hit the mode button to engage the charger?

@NickyJUSC 3 жыл бұрын

Its hard to tell, but can I use this to jump start my old Maxima 2000 car battery? Its completely dead and hasnt run in a few weeks. I just need to get it to the point where I can move it to another location within a 100 yards

@levrone0075 2 жыл бұрын

You cant jump start a car with 10 amps

@Gum05 Жыл бұрын

How do you know when to enter the repair mode? Do you try this when nothing else works? Is this where you do the battery desulfation at?

@HighTechBatterySolutionsInc Жыл бұрын

We use repair mode for batteries that are having issues maintaining a fully charged state (voltage drop with no draw), low CCA output, or capacity loss. I will typically engage the repair mode on a battery experiencing one of the above after completing a charge cycle on the charger. The repair mode will work on desulfation of the battery.

@habibkanaan2263 4 жыл бұрын

WHILE PLUGGING AND CHARGING THE REGULAR BATTERY DOES IT RECHARGE ALSO THE AUXILLIARY BATTERY IN THE BENZ E350? OR NO

@HighTechBatterySolutionsInc 4 жыл бұрын

Not 100% on this but I believe AUX battery is isolated from the main buss in the car, so charging the primary battery only will not charge the AUX battery.

@laurenanthone8859 4 жыл бұрын

I have three marine 12V AGM batteries that are now showing only 8V due to long-term storage without a charger. I have an onboard charging system but it doesn't charge due to the low voltage. Two of the batteries are connected in parallel. Can I charge both batteries at once with the Noco charger, or do I have to disconnect them first? What are the odds that I actually can charge these batteries up to at least 10-11 volts so that my on-board system can take over the rest of the charging? Thanks in advance for your advice.

@HighTechBatterySolutionsInc 4 жыл бұрын

Yes, you can charge up both of these batteries in parallel without an issue. I don't think you will have a problem getting them up in the 10-11 volt range but I would recommend leaving them on the NOCO GENIUS10 until they are fully charged - let the charger run through its paces to give you the best outcome possible

@Reillykid12 Жыл бұрын

Can you use the recovery mode on a dead agm battery? In my experience the agm batteries are sometimes impossible to recharge once they’re left dead

@HighTechBatterySolutionsInc Жыл бұрын

Depends on the battery, all I can do is tell you what we do at the shop. If the charger is not able to detect the battery out of the gate we switch the GENIUS10 to the supply mode and leave it connected to the battery for 30 minutes to an hour depending on the battery size. This will throw amperage into the battery regardless if its recoverable or not and raise the voltage level. Once the voltage has been raised from 0 then the charger should be able to properly engage on the AGM setting. Once the AGM setting runs through its charging process and the battery is fully charged we then switch the charger into the repair mode.

@jah6169 9 ай бұрын

I just received the Genius 10 Charger + Maintainer, I am planning on storing my vehicle (Genesis QV 70) for the winter....Is this the correct Maintainer? Thanks

@HighTechBatterySolutionsInc 9 ай бұрын

Yes, the NOCO GENIUS10 can properly maintain the battery in storage without an issue.

@scundoorsup5342 2 жыл бұрын

Can this be used for 2022 Porsche Targa for maintenance of its battery

@michaelm2420 3 жыл бұрын

Great review I do have two questions one is I plan on plugging this into my Ford F-150 built-in power inverter what is Inlet voltage this unit draws I want to make sure it doesn't trip my Factory inverter.? My second question is I have a battery in my bed that is powering a refrigerator I'd like this to be automatic so when I turn my truck on it'll sense that it's plugged in and automatically power up the charger my question is do I have to manually turn on every time power supply to the unit is turned off is there a way to set it and forget it we're it'll automatically go on to Prior settings when power is applied?

@HighTechBatterySolutionsInc 3 жыл бұрын

The GENIUS10 unit requires about 150 watts to operate and it will remember the last setting it was in, so if the charger loses power you will not have to re-select the correct charge setting as it will remember the last setting it was on.

@gagegr 3 жыл бұрын

You would be a LOT more efficient by installing a high output alternator and wiring your second battery into your truck as a second battery. I’d use an isolator. Look up wakesurfing boat forums on adding a second battery. It’s the same principle. They want their second battery to run a stereo for long periods, but save enough charge in the first battery to start the engine. This would be much more efficient and easier for you in the long run. You’re losing efficiency through that inverter.

@setlikeamf 4 жыл бұрын

Great video and thanks for the info. My 6 volt batteries are 232 amp hours run in series. Will this charger be fine for that? Also I have the 10ft extension cable. Would using 2 of the extensions hinder the performance of the charger? Thanks!

@HighTechBatterySolutionsInc 4 жыл бұрын

You're right on the cusp, the GENIUS10 is rated up to 230AH but you can skate by with 232 on this unit. Now the 10ft extension cable will draw the voltage down a bit on the charger, so using two of them will increase your charge time.

@setlikeamf 4 жыл бұрын

@@HighTechBatterySolutionsInc Which one is rated for 232 or should I just stick with the GENIUS 10?

@HighTechBatterySolutionsInc 4 жыл бұрын

@@setlikeamf If charge time is not a factor then stick with the GENIUS10 series. If you want them to charge up quicker NOCO also has the G15000 series unit which puts out 15A.

@adamlopez255 3 жыл бұрын

@@HighTechBatterySolutionsIncI thought that the G15000 was meant for 12 & 24 volt batteries, not 6v?

@HighTechBatterySolutionsInc 3 жыл бұрын

@@adamlopez255 It is, but if you were to wire up the batteries in series to get a 12V setup then it would be ideal for the G15000 series.

@anthonygurley4978 9 ай бұрын

when you mgetnthe battery pack out of the box do you have to charge it

@gorgemusic 3 жыл бұрын

Will this unit function properly plugged into a Honda 1000 watt generator

@bensonlew413 2 жыл бұрын

can the charger be hooked up to two batteries, either 6 volt in series as in a motor home or 12 voltin parallel as in accessory battery array?

@HighTechBatterySolutionsInc 2 жыл бұрын

Yes, it can be hooked up in either setup without an issue. As long as the voltage is either 6 or 12 then you are good to go! Just note that on a parallel battery bank hooking the charger up to the first battery will charge the entire bank. If you're looking to charge a bank in series then your connection will have to be split - positive on the first in the string and the negative on the last.

@anthonygurley4978 9 ай бұрын

and when do you know your device is fully charged and ready for usage

@matthewsiwinski2869 3 жыл бұрын

Hi there, I have this charger for my 2015 x-trail. It has a efb battery and is stop start. What is the best charge setting for the stop start battery please. I also bought the gb70 jumper pack as it has let me down a few times now so its for pease of mind. Many thanks.

@HighTechBatterySolutionsInc 3 жыл бұрын

The EFB's are still going to fall under the standard 12V setting on the charger

@juliepryor2635 4 жыл бұрын

Do all the charge indicator lights stay on when charge is complete. The instructions and different videos are a little confusing. I’ve had mine plugged up for a day and all the lights are on and the green just keeps pulsing.

@HighTechBatterySolutionsInc 4 жыл бұрын

Once the battery is fully charged the last green LED will be the only light showing a solid green. If it's flashing at the moment then it's topping the battery off - leave the charger connected to let the charging cycle finish.

@JimWhySoSlim Жыл бұрын

What settling would a 2022 Honda Accord use? 12V or 12V agm? I’m thinking the 12V agm based on your video but not 100% sure.

@HighTechBatterySolutionsInc Жыл бұрын

I believe the OEM battery for the 2022 Honda Accords are enhanced flooded batteries or EFB's. These units would require the standard 12V mode of charging.

@darrickhummel7650 3 жыл бұрын

A nice review. How do you get the 12V repair function to work? I switch to it and it just blinks red. I’m trying to figure out how to get it to solid red/activate.

@HighTechBatterySolutionsInc 3 жыл бұрын

The blinking red is what you're looking for, the light will continue to blink red throughout the whole repair process. Once it's completed you will get the solid green LED on the charger.

@landonwoodruff 2 жыл бұрын

This is the same question I had! The manual said solid red everything else I saw said solid red and mine is just flashing.

@cheryllinford443 2 жыл бұрын

@@HighTechBatterySolutionsInc how do you know if your battery needs the repair mode if you can get the car to start with the charging mode only with one or two red lights across the bars and it has not reached the green light yet? When I select the Repair mode it just flashes red.

@HighTechBatterySolutionsInc 2 жыл бұрын

@@cheryllinford443 We recommend using the repair mode if the battery is not performing as it should, or if it's been left in a discharged state for longer than 30 days. If you accidentally drain your battery and its not been left in a discharged state for 30+ days then we recommend hitting it with the standard charge mode.