thanks mustie! i am 72 years old and i have finally been on a 4wheeler in the woods! the $38 carb is jimdandy!

I’m actually surprised Mustie bought something new.

Well that just made me feel old! I worked for a Suzuki dealer when the Vinson came out, cannot believe it's been 20 effing years!😢

Once while hiking miles into the deep woods I came across a log hunting cabin on top of a small hill, good size like 10x20, but a little slumpy in the back, had a huge critter hole inside like 5gal bucket sized, mattress complete gone with just the rusty springs remaining -- oh and I was just guessing that it was hunting cabin because the stone fireplace had Joe and Fred 1929 inscribed into the stone mantle, heh it was teh gay20's. snort Anyway the best part was the builders didn't anticipate the river changing course over time - where it had now been digging into the hillside, you walk out the front door and there's like 3 to 4ft of earth before a 25ft nearly vertical drop to the stream. cool spot

The device on the left side of the old carb is a decel valve. There is a diaphragm under the cover that closes an idle circuit air passage when you shut the throttle at high speed. The purpose is to richen the mixture and reduce popping in the exhaust system under decel. The brass electrical device on the bowl is probably a heater that warms a fuel passage in cold weather. You could test that by applying 12v to it and see if it gets hot.

Ever since you adjusted the chest mount to point further ahead it makes the ride-alongs a whole lot more fun! Thanks for doing that.

"its a 2003". me in my head: basicly brand new. "its 20 years old". me: Oh..

love the nature shot at the end. I remember you always used to do that at the end of all your videos. It's been a while. Was nice to see that again with the eagle.

As someone that has done my share of brake work, I'm telling you that if you want any longevity out of those brakes, you MUST put some kind of lube on the pins of the caliper. Sil-glyde is cheap and usually will stand up even if you submerge in water.

I think for 36 bucks, SHIPPED, that was probably one of the best buys you could've made. You had a serious come up that one free pile with all the antique stuff (had that light box and other awesome stuff) but man that little 4x4 does the trick with that carb it sounded SO much better when you first started it on the stand, I was extremely impressed!! Great video, thing rides pretty nice at the end!

I would love to see the bikes and cars that you have kept. It make a cool video to see your collection. Anyone else ?

This made me feel old. I remember watching the video of you installing the yellow bashbar/bumper on this machine all these years ago. Keep the videos comming they have been a great source entertainment for me here on the platform.

Looks like the exact China carb I got for my Kawi 300, in that application, that little round plug you found in the bowl is a carb preheater. Thanks for the video as always!

I did this on my four wheeler. It was a no brainer the whole carb was less than the carb rebuild kit from the dealer. works great. Mustie1 they do have low speed screws that have an extended shaft and a thumbwheel. Still not as easy as a side screw but ten times easier than stock.

So nice waking up on a Sunday morning late and there's a Mustie1 episode posted. Of course it almost wouldn't be a Mustie1 episode if Darren wasn't tearing a carberator apart to see how it works and diagnose what's wrong with it. It amazes me he actually bought a high ticket vehicle new 😅😂 No matter what it's gonna be highly entertaining watching him getting his 4 wheeler running reliably.

Thanks Mustie for doing the comparison. I call it a win for sure.

Hey Mustie, I am 75 . Really enjoyed the fix and especially the ride! Thanks so much……

Was interesting to see how quickly the oil got dirty after the change.

The difference in cost from the stock carb to the aftermarket is extreme! You could buy three of them and store them on the shelf if there's ever any problems in the future. Good video Sir.

This video is perfect timing! I started getting my 2000 Honda Rubicon back up and running 2 years ago this month. It had been sitting in the shop maybe 8 years. Heading out to the shop now to gather up the remaining parts and get back on her. Thanks Mustie!!! 😊

Always a pleasure to come in from my shop after getting my old Warrior ATV running perfectly, to find a new video by Mustie getting HIS old ATV running. Beer time!

Gotta say 20 years is a pretty good run for about any machine. Nice to see this one still getting some love.

Where I was at college, you could tell how good a weekend the local joy-riders/car thieves had by counting the burnt out cars dumped outside the village on a Monday morning!

The thing screwed under the carb is an heating element to prevent it from freezing. If you try to use it sometimes it use AC , like electric choke

I had a prairie 360 that had similar issues, turned out to be the intake valve lash. Reset the valves back to spec and bam ran like new again.

Folding Corona saw....I keep one in each of my machines, along with a hatchet, small shovel and a fixed blade knife....I've used all of them at one time or another. The corona saw is a gnarly little cutter. Much better than the old Sierra saw

I did the same carb swap on my Vinson about a year ago and it is still working fine. I ride it 3 or 4 times a week. Summer or winter, it starts easy and runs great.

The external battery is genius!!! I have 2 Honda atc's that both need batteries, I have access to very cheap batteries but hard to get one to fit the bike, this is what I will do! Cheers mustie!

The small electrical device is a low wattage heater 15 to 30 watts to help with cold weather starting. There is usually a thermistor in line with it and shuts off as the engine warms up. But all you you have to do is put an inline switch to shut off the heater after 10 or 15 minuets of run time. You got it running though cool!

Did I hear right, not a yard or roadside find, but new ! Good for you Darren 👍🙂

The mouse problem. Is most definitely the result of not having enough granny gowns in the neighborhood. I'm talking about the blue dresses with white spots. You get the count of those blue dresses with white spots up to where they're about three-quarters of the people you see walking around every day or wearing a dress, and you will no longer have a mouse problem. One of the side effects is though if you go to work in your garden you'll find a lot of hidden surprises so gloves are recommended. Have you figured it out yet?

Don't forget to adjust the intake and exhaust valves, especially if it hasn't been done in a while.

I have a 2003 Suzuki Eiger that had carb problems, similar to your symptoms, I removed it and thoroughly cleaned it, I also moved the throttle needle up about .020 in. That was 5 yrs ago, it is now 2023 and I have had no problems since. This is a. 400cc and throttle roll-on will spin tires in 1st or 2nd gear. Top speed is around 50 mph.

Thanks! I love all of your videos. I watch them over and over again daily!

Glad to see a personal toy we haven't seen in a while brought back to life. I also happen to have the same ITP AT589 tires, but yours are 27" and mine are 26"

Mustie, ever since watching your content I've marveled, and learned from, your mechanical skill. But more and more I'm also impressed by your artistry; from the custom engineering and fabrication to your cinematography, narration, and editing choices. Really enjoy the channel! Keep up the good work!

Awesome as always.Thanks for sharing and taking us along

This was a very interesting video, I love seeing these comparisons of OEM vs other. Thanks for another great start to Sunday.

It's a pleasure watching you videos. Thanx for another one.

Thanks for the trail ride, Mustie. This old townie likes to get out and about now and then. All the best, Mart in England.

Thanks for taking us on the trail ride on this spring day. Weather here was so nice today I had my sliding glass door wide open.

Hey Mustie 1, nice machine. The plating difference is zinc plating with yellow chromate conversion vs zinc plating with clear chromate conversion. I bought a knock off carb for my Sthil weed wacker and to this day it has outlasted and ran BETTER than the Zama original ever did. I have a feeling the EPA gets involved and the manufactures have to set them up too lean etc to meet emissions, but that's just a theory. You've given me inspiration to do some maintenance to my Yellow Polaris Sportsman twin 700 this spring. First thing I ever Bought new (2004) Thanks

Awesome video as always...truly enjoy your wrenching but more over your fabrication...going to your endless stash and finding exactly what you need is epic. Appreciate all you do and share 😇🛠️🔧🛻🚜🇺🇸🏍️🛵🚙

I have been watching your show for some time now and have learned more than I can put into words. Thank you for your hard work! BTW, I have an old used Kawasaki Bayou that has been sitting for years and this show has encouraged me to get it running.

Some of those mini chainsaws that use batteries would be a good addition to your "emergency" stowage. As long as you keep charged batteries in with it. The one I have (a fairly cheap Amazon unit) is amazing. I can easily trim large diameter brush with it. Could even take down a good small tree. I still use my Stihl for larger jobs, but this thing is really handy! Amazed at how well it works. Would probably be good for on the trail when you don't feel like working hard with a hand saw.

I did the same thing...I picked up an 2012 Ariens riding mower that hadn't been used for years. It was $70 for carb kit, so I ordered an Amazon carb for $27 with filter, runs great so far!

I bought a carb for my 93 Honda 4 wheeler from Amazon, and it ran out great. It saved me a bunch of money, too.

Nice trails, gets me excited to head north within the coming weeks to visit my land. Haven’t been since 2017, life happens, thanks for reminding me to chill a bit and go hang out in the woods.

Worked on one of these last summer. Replaced a few small parts in the carb, the throttle cable, and adjusted it all and it was fine.

New carb is set up to use an electric enrichener valve. It is controlled by a temperature sensor. If you have a manual valve you do not need the sensor. I put the stock jets in the aftermarket carbs. I just got a cheap aftermarket carb for my Honda 450 Foreman and popped it on. Works really good. Only thing that I had a problem with was the mixture screw. The spring was very weak and it was missing the tiny O-ring. It kept backing out. I replaced the spring with the one out of the original carb and I had to buy the tiny O-Ring because I lost the one out of the original carb.

It’s so nice to see the older quads back running & being enjoyed

Thanks for the shop time and trail ride Mustie1!

With the exception of one bad fuel shutoff solenoid that I was planning to delete anyway, I have really good luck with aftermarket carbs. You may get a bad one here or there, and they may not last as long on some applications, but when the cost of the aftermarket is a fraction of the OEM, it really doesn't matter if you have to go through one or two of them. The money you save is well worth it. I will buy OEM if it is a show room machine, but there is no reason to on most applications, unless the OEM is inexpensive. The price of most OEM carbs is just unreasonable.

Nice. Always enjoy the bits at the end as well.

Thanks for the ride! Nice job!

i actually picked up a 2005 arcticcat 500m, which is the same engine as in your suzuki Mustie1. it had less than 300 miles and only about 75 hours on it! needed a new needle valve after running it for a couple hours, but it was my dream atv since high school and its basically brand new still! i absolutely love your videos and im sure this one will be no different. thank you for the awesome content!

Maybe it's been said, but I've found boiling a carb in vinegar gets out deposits nothing else can. I think the heat opens up passages just enough. I did it on an expensive carb for a john deere garden tractor. Found a hardened chuck of varnished gas in the pot when I was done. Worked great after.

Awesome video Mustie1 👍👍👍 I rode a 4 wheeler several years ago, love ride one again.

Well that was fun! Now that you have a receiver, make yourself a Drop Down insert that can take a D Ring. Then you can run your winchline under and behind yourself and keep it centered to the machine if you ever need to winch yourself backwards. Thanks for sharing 🇨🇦

Just wanted to say thanks for all the small engine carb rebuild videos I've been watching many of your videos even a lot of your old videos from 5 & 6 years ago. I used to be really bad with carbs I'm slowly getting better with them thanks to your videos. Just like I'm currently working on a craftsman snow blower I got from the trash guy said the engine was locked up. I got it home pulled dipstick and it smelled of gas so right there I knew what happened to it. Pulled the spark plug and it was full of gas and pulled the cord and all the gas shot out of it. So I'm rebuilding the carb now and will change the oil and hopefully it will run on its own

Preventive maintenance is a necessary thing thank you for showing us how easy it is to do this was an excellent video with outstanding content six stars brother

Had a Vinson and actually loved the quad for a short time until it became perpetually problematic. I sold it and bought a honda foreman and it has been literally flawless for the past 10+ years I've owned. The Vinson's powerband is better but im old so the Foreman works just fine

Mustie, I think that burned out wheeler would make an excellent video for a put it together out of what you have in parts stash!

Great Video. Always a great camera angle. Perfect editing, Skill level, genius level! I believe you could fix a bad day! Thanks Darren. I have turned a BUNCH of folks on to your channel. I love how you can pick up stuff off the side of the road and have it going in one video. I remember you worked on your Daddy's boat outboard motor. You tickled him! THANKS DARREN !

The electrical part on the new carb is a carb heater to prevent icing on cold days. My Vstar 650 has them and when the go out, you know it. Below 40-45 degrees the carbs ice up really bad. I chased this problem for a while on mine. I took the air filter housing off after it stranded me and looked inside the tube between the filter housing and carbs. There was frost inside there and the temps where low 40's. Summer time on the Blue Ridge Parkway after a cold front and rain passing over Mt. Pisgah. It sucked, but I nursed the old girl home and replaced those little heaters. I've talked to people about them but no one seems to know exactly what controls them. I assume it's the same little module that controls the electric fuel pump. The carbs are down draft and sit up under the tank so at half tank the bike quits if the fuel pump isn't running.

That was great never seen a carburetor so cheap but it works so use it and new to you got it going on service it and ready for another year of use great job Mustie but if it works Mustie can fix it thank you can't wait for next video thank you for sharing and your time.

Thanks for the great video, and a nice tour on your trail. 😊

Awesome you got the 4 wheeler running like new. Pretty cool

Stunning trail & happy for your success with this machine. Always a fun video …Mustie is Number 1 🇨🇦🇨🇦🇨🇦🇨🇦

Always watch till the very end...magnificent. !

I have an Arctic Cat atv. Was having problems with carb, purchased a new carb from Amazon for 18 bucks. Now it runs great.

Thanks for the video! I wanted to see the difference between the knock off carbs and the originals.

I rebuilt the carb on my 2003 Yamaha Roadstar last year. It had the same problems and used a similar CV carb. I had gone thru it a couple of times over the last ten years with not real long lasting fix until last year when I replaced the decel valve which changed how it run completely. Now it starts and runs great and idles instantly . The brass electrical item you removed is a carb preheater unit.

A fun video. Reminded me of good times in the past. Dave Goodwin

Congrats Mustie1 on finding a new carb for ur 4 wheeler. sounds great afterwards..

I had the 07 king quad loved it.

The small round cover has a diaphragm operated valve that cuts air to the pilot circuit under engine braking to improve control during descents.

Those Vinson's 500 were animals. Id have done valve lash vs a knock off carb. another one lives however!

Thanks for the ride

Success! Fun, thanks Mustie1.

Wheeew, Oh Man!!! We was haulin' ass at the end there! That was fun as hell!

$36 dollar knock off carburetor vs $700 OEM one. You can buy a new 36 dollar Carburetor each year for 18 years and still save money over the OEM one. Happy you got it working better and now can enjoy it more.

Thank you for sharing. Enjoyed.👍

Ah, the sunday mustie movie! I look forward to this every week

Great way to start a Sunday morning, hanging out with Musti1.

I like the video on the 4x4. I have a sxs that needs some work on the carburetor are about the same l, it was a lot of help. Thanks again

Great video. It was really hauling it at the end😂!! Can’t wait till the next project. Thanks

looks like a really fun area to ride, wouldnt mind seeing more vids of that.

Great car Derek you're videos are awesome

right on and it worked wish I had the same luck

It is a common problem that the rubber seal from that choke piston is worn out (or too hard) or the cable is not properly adjusted. So the engine is always running with a little extra fuel from the choke. The result is that the mixture is a little too rich and the engine died when idling.

Good job! Im in Kansas City, Mo and have been seeing more and more Bald eagles in the last few years in town.

Nice score for 35 beans👍🏻 for 20 years old it’s a sweet machine Mustie

Great video thanks. and as usual love the commentary 🙂

Great job as always 👍... Thanks for sharing. Nice Atv.

Good video Mustie, Those enricheners can be a pain I've seen between the cable or the plunger sticking or ageing going out of adjustment idle speed and mixture can be trouble some or all of the up to four mixture jets on Suzuki's. Nice machine.

Hey brother. This is a super common issue. But relatively not well known for a fix. But I have been working on them a long time. There's what's called a needle jet. It's that little tube that's under the main jet emulsion tube. The one that sticks up in the venturi. Take it out and stick the carb slide jet needle through it and hold it up to the light. You'll see why that's the issue

Very similar to the carb on my 2000 Honda, which is on the bench right now. That mystery fitting looks like the carb heater on mine.

i use wet clutch motorcycle oil in my 83 honda atc 200. as for a 4 wheeler mine is the polaris sportsman 400 2 stroke. the polaris i was the first to register it for trail use, last couple owners only used it on their camp properties.

Your wrenching is always fun Mustie, but I really enjoyed the last several minutes of you out in the woods on this wheeler. Maybe change up from wrenching and do a trail clean-up vid, maybe drag out some tools and bone out anything useable off the old burnt wheeler, just a day inna woods kinda thing.....