Most heaters are on demand ignition type firing. They do not maintain a constant pilot.

Hi Richard. Blowers are typically an on/off mechanism. However, controlling them with automation is certainly possible and a standard operating procedure for most reputable installers at the time of your automation installation. If you have installed an automated interface/controller at some point after initial pool pad installation, it will simply connect to one of the relays on the control unit. The only problem would arise if there are not enough relays available to control all of the items you desire to automate. For example if you are running a hayward omni "VS" automation unit (the small one with a user interface the size of a large smartphone mounted to the wall) you only have a couple of extra relays. If those relays are being occupied by multiple light controllers, valve actuators, etc., You may not have enough to automate the blower as well. This would be versus a full omni control box (the size of a fuse panel) which is able to expand and add multiple relays and control multiple items from blowers to landscape lighting etc. Think of relays like remote controlled on/off switches. Everything you want to turn on/off remotely needs one. If you have enough you can assign them to just about anything. Hope this answers your question.

The Hayward blower works off of a relay. If you have a standard VS operating unit (the small one that mounts the size of a smartphone) then lights use one, and any other on/off accessory uses the other. Those small ones are not expandable, but the large omni's (the size of a fuse panel) come with 4 relays and are expandable to run everything operating with an on/off switch......blowers, actuators, landscape lights etc.

Hi There. Hayward blowers can be automated with an open relay on the Omni system. It would have to added if not already present on the system.

You're welcome! Please let us know if we can help further!

Thank you! Please let us know if there is specific content that may further help you!

The best video we have right now for anything cold is here: kzfaq.info/get/bejne/pZeciLyKrdXaj3U.html Hope this helps!

Hi there. A "CE" code is a communications error code. The board can't communicate with the ignition system. With what you have already posted, it sounds like you need a new control board for that heater. Corrosion should not be a common problem on that board. I would double check and make sure you have a backflow preventer between your chlorinator chlorinator or salt cell and the heater. They are made to be in the weather so that is somewhat unusual

@@CrystalEdgePools I believe there is a backflow preventer, our heater is 11 yrs old and this will be the 4th control board. Hope we don't need a new heater, as we only heat the spa in the pool and have solar for the pool. Thank you for the help.

We have not had any problems with the propane heaters and we have noticed a slightly yellowish flame. If it ain't broke don't fix it😜

A reg 20 lbs propane tank holding 4.5 gallons of propane would give you how much heat time on the pool??? I have a small 15ft round pool. And just want the water around 75-80. Gas line is on the opposite side of my house, so that option is a no go. Ty

​@@richdelacruz5222 I have a 15'x30' oval and I keep the water at 80° I'm in the country so I have a 1500 Gal tank.

@@nomecaca how often do you turn the heater on? Or is it every time the pump runs, the heater runs? Ty !

@@richdelacruz5222 no it's on its own thermostat, the heater does kick in mostly in the evening as my pump is 2 stage and runs at a lower flow rate during the day.

Cool idea

Hello, The pool heater should enter a standby mode automatically if it senses no flow. You really only need to enter the standby mode manually if the heater is running and you want to shut it off while the pool remains running

The heater needs a solid water flow (usually 2750rpm or better) so that's normal.

Noted. We will cover in a future video. Thanks for the suggestion!

Hi Carl. As long as the flow is adequate (meaning there are no restrictions slowing down the system) 40% should be enough to keep that heater going. If you find that you have an LF message on the heater, You may need to increase the flow from the pump.Typically, 60% or better is what we recommend to avoid interruptions. Baskets and filters need to remain pretty clean when trying to activate the pressure switch at a low flow with a Hayward heater. They tend to be a little finicky.

Hi. Sorry to hear that your having problems. My experience in the past has been that this is often an ignitor. However, it can be difficult to diagnose and I need to make sure that you understand I can Only speak from experience and am not a Hayward authorized tech. Please respond back when you do find out though so others can benefit. Thanks so much!

@@CrystalEdgePools - so I replaced the ignitor but that didn't do it. It ended up being that I needed to reset the heater. The technician took it off of bo (60) code since it was tied to the Omnilogic, then reset the pool and spa heater settings, they were too low so he set them back to the max settings 90 pool /104 spa. Then he set it back to bo (60) code so it could be controlled through the Omnilogic panel and it fired up. He thinks it may have glitched due to a power outage/surge that may have caused it to reset the settings somehow. Hope this helps someone else.

Pump must be on and flowing at a minimum speed to activate the flow switch on the heater. The heater has no internal pump of its own

Not consistently. It's not unusual for a gas odor to occur at immediate installation, however it should dissipate and not continue.

Not consistently. It's not unusual to notice a smell initially after installation, but it should dissipate and not continue.

This is possible with a unit that will link the heater to an app. This is an iaqualink unit for Jandy, an omnilink (omnilogic) with Hayward, or intellilink (intellitouch) with pentair. It's important to understand this controller must be added and programmed to the system to use the accompanying apps.

The temperature can be displayed in Fahrenheit or Celsius. TO change the display, use the “MODE” button to place the heater in “STANDBY”. Then press and hold the “UP” and “MODE” buttons until the display shows the °F/°C selection. Press the “DOWN” button to toggle between selections.

Specific to Hayward heaters, 'bo' is not an error code. It means "bypass operation". You can clear it by pressing STANDBY and the holding DOWN and MODE for 3 seconds

You should be able to cycle through the mode button to off. If it's running, it will likely go through a "cool down" cycle before it stops running even after you have selected "off"