Wiring a NATURAL GAS SWIMMING POOL HEATER

No video

Wiring a NATURAL GAS SWIMMING POOL HEATER | Hayward

Рет қаралды 26,989

Күн бұрын

In this video you'll see how a natural gas pool heater is wired and how the wiring is covered from 240 volts (double pole) to 120 volts (single pole). Also, you'll see how a GFCI circuit breaker is installed and tested.
Call 732-770-1437
Point Pleasant, NJ Licensed Electrical Contractor | New Jersey Electrical License & Business Permit Number: 16557
Like Us on Facebook:
/ classic-electric-llc-1...
Classic Electric, LLC
Point Pleasant, New Jersey
08742-5406

Пікірлер: 37

@bjleau76 2 жыл бұрын

Great video, was extremely helpful especially the explanation of the jumper on a Hayward pool heater, Thank you

@electricalron 2 жыл бұрын

You're welcome!

@vincentmeo6280 2 жыл бұрын

What a great video now I know For 21 years I was a plumber

@michaelleddy3701 2 жыл бұрын

Ayeee a new joisey guy .

@wallydesouza1 Жыл бұрын

I have a outlet from out pool heater. Pool straight out of the panel. 15 amp. Will it power this same unit ?

@richdevito78 Жыл бұрын

What would happen if u did not switch module from 240/120 or vice versa?

@kidR0BOT Жыл бұрын

Pssstttt next time wire it on the load side of the time clock that controls the filter pump. No extra breaker needed and the heat won’t run unless water is flowing.

@vince6829 Жыл бұрын

Thank you.

@williameisenberg1999 Жыл бұрын

Hi Ron , Thanks for the video ? What kind of linesman pliers are you using can you give me the brand name . They look really nice to work with … Thanks Again Eisenberg Electric. Simsbury ,Ct.

@electricalron Жыл бұрын

Hello, these are Klein Hybrid pliers. They have built-in crimper and strippers. My favorite lineman’s pliers ever.

@williameisenberg1999 Жыл бұрын

Thank you ,, Just ordered one !!

@SqueakyHinge Жыл бұрын

Why don't you have a bond on the heater? Is it because the heater is far away from the pool/pumps?

@electricalron Жыл бұрын

It is bonded!

@Inmate533 Жыл бұрын

How does the heater know when the pump is running? Does the heater have a flow switch that only allows the heater to turn when the water is running through it? Sorry if this is a dumb question.

@electricalron Жыл бұрын

Not a dumb question. I imagine through a set of contacts in the filter. Definitely wiring within the appliance.

@SqueakyHinge Жыл бұрын

The heater has a pressure switch on the inlet of the piping system which will close the control circuit if that pressure sensor senses pressure - from the pump running - so the heater will run.

@jimamentas7190 3 ай бұрын

Can you use regular 12/2 with ground to connect inside heater?

@electricalron 3 ай бұрын

if the units outside no.

@jimamentas7190 3 ай бұрын

@@electricalron could you explain why not? Just curious

@markgeyer1 Жыл бұрын

What AMP was the beaker (15/20)?

@Dr.Colone_Ucantmakethisshitup Жыл бұрын

Rwplaving a hayward heater

@booSackk 2 жыл бұрын

Do you have to pull permits for every single one of ur jobs Can you list some examples where you dont pull permit

@electricalron 2 жыл бұрын

Repairs & maintenance and I do a lot of that. Permits for any new wiring but not for changing out light fixtures or changing GFCI’s.

@booSackk 2 жыл бұрын

@@electricalron thanks for replying, i almost have my masters and am looking forward to start my journey in vancouver area, always curious about the permits and doing it right. One of the jobs u had, installing light fixtures in garage with piping and motion sensor, did you need permit for that? Or shed wiring Thanks!

@electricalron 2 жыл бұрын

@@booSackk Best to check with building department. It’s Canada so I’m sure it’s not the same as here.

@daviddillard8206 Жыл бұрын

Where was your sensor wire? All Hayward heaters have one.

@electricalron Жыл бұрын

Sensor for what?

@SqueakyHinge Жыл бұрын

The pool water sensor as well as the pump pressure sensor and the control thermostat are all located inside of the heater. There can be options of a remote sensor control.

@markmenner6922 2 жыл бұрын

Hi Ron, on outdoor outlets for a deck does NJ code require gfci outlets and gfci breakers or is a gfci breaker with wr outlets ok.

@electricalron 2 жыл бұрын

A circuit breaker or outlet is acceptable because it's only required to be GFCI-protected. I will tell you the outlet will be cheaper than the circuit breaker. The outlet MUST BE 'WR' which means weather-resistant.

@markmenner6922 2 жыл бұрын

Thanks Ron

@wallydesouza1 Жыл бұрын

Does that pool heater have to be hard wired ?

@electricalron Жыл бұрын

No, you could attach a cord to it and plug it in I suppose.

@wallydesouza1 Жыл бұрын

@@electricalron like a dishwasher power cord I’m thinking. I’m just wondering if 15 amp dedicated is enough for this 400k btu gas pool heater

@moo-r8199 6 ай бұрын

I dont fish the wire i just push in it with soap it faster

@mackfisher4487 Жыл бұрын

Why is it that some trades running their class-II wiring with no concept of dressing wires in a workmanship manner. I'm always surprised when I see HVAC equipment wired neatly some folks seem to like spaghetti.

@electricalron Жыл бұрын

Some just don’t care about themselves so naturally they don’t care about their work.