Orca Slicer Pressure Advance Testing and Calibration: Unlock Sharper Prints (Ultimate Guide)

Рет қаралды 5,583

Ай бұрын

Orca Slicer Pressure Advance Testing: Level Up Your 3D Printing: In-Depth
This in-depth video will explore pressure advance calibration tuning specifically for OrcaSlicer 3D printing software.
Pressure advance is a powerful setting that can significantly improve your 3D print quality by reducing stringing and blobs. But calibrating it can seem daunting. This video will be your ultimate guide, walking you through the entire process in OrcaSlicer from start to finish.
Whether you're a beginner looking to understand the basics or an experienced user wanting to optimize your prints, this video will equip you with the knowledge and techniques to master pressure advance calibration in OrcaSlicer. Get ready to unlock sharper, cleaner, and higher-quality 3D prints!
References:
Ellis' Print Tuning Guide: ellis3dp.com/Print-Tuning-Gui...
Quick Links:
Minilam3DP Klipper Calibration Website: minimal3dp.com/
Klipper Calibration Spreadsheet: tinyurl.com/287waw78
Email: minimal3dp@gmail.com.
Minimal 3DP on KZfaq: / @minimal3dp
NEED HELP?
Schedule a FREE 15-minute Google Meet Consultation:
calendly.com/minimal3dp/m3dp-...
NEED MORE HELP? Contact me regarding a 1-2 Help Session. I can be reached at minimal3dp@gmail.com.
* Note: I may earn a commission at no extra cost if you click an affiliate link and purchase. *

Пікірлер: 29

@adamsvette Ай бұрын

Your pressure advance K value can change depending on filament type AND temperature. Just something to keep in mind. The K value you determine is specifically for THAT filament at THAT temperature.

@minimal3dp Ай бұрын

Thanks foir the feedback.

@andreferrato Күн бұрын

Thanks for the worksheet.

@stefanguiton Ай бұрын

Excellent videos as always

@minimal3dp Ай бұрын

Glad you like them!

@JohnStruemph Ай бұрын

Thanks Mike! Great vid and info! Be well and happy printing!

@minimal3dp Ай бұрын

Thanks for the kind words. I appreciate it.

@thebrelon Ай бұрын

I find the line test is the better of the 3. easier to read and less difficult to decide what's good and what's not

@minimal3dp Ай бұрын

@@thebrelon I like either of the line based tests. My easier and quicker than the tower.

@jeffellis1149 Ай бұрын

Great video, thanks! I use a cheap usb microscope for examining the results. Very revealing for stuff like this.

@minimal3dp Ай бұрын

Glad it was helpful!

@contomo5710 Ай бұрын

you know, the guide and explenations are so good, im not even gonna complain about the mic peaking^^

@minimal3dp Ай бұрын

Thanks for the feedback. I struggle horribly with sounds.

@contomo5710 Ай бұрын

@@minimal3dp its totally acceptable, ive watched stuff with way worse audio with not as good content before, i just may be a lil picky when it comes to sound! :P

@stevehanwright481 Ай бұрын

great video you have new subscriber

@minimal3dp Ай бұрын

Thanks for the sub!

@stevehanwright481 Ай бұрын

Hey i just found a neat trick print the PA line test then look at it with the lines running left to right but at about 10 to 30 degrees to the build plate it real help tell when the lines go from bad to worst then put you finger about half way between

@minimal3dp Ай бұрын

Thanks for sharing. I will give it a try.

@stevehanwright481 Ай бұрын

like you said the line and pattern method seem the best to get a definitive result, like Ellis states one you have an idea for a range you can reprint a range from .02 to .04 in .001 intervals if you like ..

@minimal3dp Ай бұрын

I am wondering at what decimal place the adjustments stop making a difference.

@DaveYoutube-qc3qy Ай бұрын

I’m assuming speed and acceleration settings would affect these calculations?

@minimal3dp Ай бұрын

It will. You.want both set to your preferred values before you start the PA tests.

@user-gh8tw1sv7o 20 күн бұрын

Need turn off acceleration? (Klipper document say this) In slicer ...or need put codes to console before PA? (Klipper document says this)

@minimal3dp 18 күн бұрын

I turn it on in the slicer and don't put it in my klipper printer.cfg.

@ruckus226 27 күн бұрын

what are the slicer settings suppose to be?

@minimal3dp 24 күн бұрын

What do you mean?

@RoofusKit 9 күн бұрын

I think the PA Pattern test is a lot easier to read.

@AndrewAHayes Ай бұрын

You would think that once you had completed and entered in your manual calibration results that the auto calibration would centre around this new value, but NO! it continues to use the three values it always has to test the flow!

@minimal3dp Ай бұрын

I believe most of the test use "standard" values.