Ortur

No video

Ortur

Рет қаралды 10,685

Жыл бұрын

Hi, today I will engrave an AI image on to a 10x10cm white ceramic tile, I will be using TiO2 (Titanium Dioxide) applied using an airbrush, all will be done using the Ortur laser master 3LE 10W machine, I use TiO2 to get great looking grayscale shades and a really long-lasting finish on my tiles & plates, this is the best way to get that extra sharp, clean & crisp finish to your work, and to amaze your family, friends or customers with the final results. #laser master 3
Please hit the LIKE button & SUBSCRIBE.
Thank you.
Please check out links below.
If you're interested in purchasing the Ortur laser master 3 LE engraver or software I use, please check out the links below.
Official Ortur Discount code:
OLM3 LE: 60FORLASER
Accessories: 10FORLASER
My Facebook page where you can see many examples of work done:
/ lightworkz.graphicdesign
• Laser Engraving
Ortur laser master 3 / laser master 3 LE:
ortur.net/prod...
Software that I would recommend:
ImagR: www.imag-r.com/
Lightburn: lightburnsoftw...
‪@ImagR-Laser‬ ‪@ORTUROFFICIAL‬ ‪@HouseOfLasers‬ ‪@LaserLivestream‬ ‪@LaserEngraving911‬ ‪@orturnet‬ ‪@lightworkz61‬ ‪@lightburnsoftware7189‬
#laser #engraving #ortur #laserengraving #lasermarkingmachine #lasermaster3 #glassengraving #engravingmachine #orturlasermaster2 #glassengraving #gifts #engraving #engravingmachine #facebook #lasercutting #orturlasermaster2

Пікірлер: 59

@ltrick2387 Жыл бұрын

Just looked at some of your other videos. You are super talented!

@lightworkz61 Жыл бұрын

Well thank you so much for your kind words, hey I keep trying ;)

@ianolegario5590 10 ай бұрын

Nice work again. 👏

@lightworkz61 10 ай бұрын

Thank you ;)

@infographie 6 ай бұрын

Excellent.

@lightworkz61 6 ай бұрын

Hi & thank you ;)

@jcarloni Жыл бұрын

Awesome job.. !Can you tell me what you mix Ti02 with and the ratio plus which air brush you recommend? Thanks

@lightworkz61 Жыл бұрын

Hi & thanks ;) I mix Tio2 with standard thinners, 1 teaspoon Tio2 with 3 teaspoons of thinners (3to1), you need to mix it well it for about 30 seconds, you will need the consistency of milk to use it with an airbrush and this stuff dried super-fast, I bought a cheap airbrush from eBay with built-in compressor, and it works great. link below ;) I hope this has helped, thanks ;) link: www.ebay.co.uk/itm/403997599871

@jimhamilton2680 10 ай бұрын

Loved the 3d picture of the bird. Where can I learn how to do this bird from the beginning?

@lightworkz61 10 ай бұрын

Hi & thanks ;) the bird design was made using Leonardo AI, then in lightburn play with gamma & contrast till your happy with the way it looks, then follow my process to engrave it: Spray tile with Tio2, engrave then clean up just like in my video ;) speed and power will depend on your machine ;) Thanks.

@cathello2900 3 ай бұрын

Hi and thanks, it's cool. I didn't really understand it a bit. this is a ceramic tile. and you just sprayed it with white tio2?

@lightworkz61 3 ай бұрын

Hi & thanks, yes it's a white ceramic tile and sprayed with a mixture of Tio2 & thinners, just a light coating, to take away the shine from the tile, the Tio2 will let the laser beam burn into the ceramic coating and make a permanent mark on the tile ;) many thanks for the comment.

@adelgicioalmeida5696 Жыл бұрын

Beautiful work, where can I get this image?! Thank you for encouraging this type of work!

@lightworkz61 Жыл бұрын

Hi & thank you for your kind words about my work ;) I can't find a way in KZfaq to forward you the image, if you have Facebook look me up and I can give you many images ;) facebook.com/lightworkz.graphicdesign Thanks ;)

@isasaurio Жыл бұрын

hello master, in what way did you use the image (DIther, jarvis, halftone, etc..)

@lightworkz61 Жыл бұрын

Hello my friend, for this video, I used jarvis ;)

@ltrick2387 Жыл бұрын

Wow! Really nice. Can you share the original image and how you prepared it for lasering (Image R, etc.) Thanks!

@lightworkz61 Жыл бұрын

Hi & thank you ;) I would luv to share my images with you but I can't find a way to insert an image in this msg ;( if you would like to msg me on Facebook I will send you as many images as you want ;) facebook.com/lightworkz.graphicdesign I used Leonardo AI to generate the image in the video, it's amazing what can be generated with just a few keyword's ;) I use Lightburn/Photoshop now more than ImagR (paid version) for my image processing, mainly dither or Stucki and play with contrast/brightness & gamma, I hope this has helped. Thanks for the comment ;)

@ltrick2387 Жыл бұрын

@@lightworkz61 Thank you so much for sharing this information!!! I'm new to lasers, but videos like yours are both informative and inspiring. Again, thank you!

@lightworkz61 Жыл бұрын

@@ltrick2387 Thank you so much and your most welcome mate, if you have Facebook then you will find sooooo many laser groups that you can join, and everyone in the groups are very helpful, hey we all started from knowing nothing ;) laser engraving has a heavy learning curve, and you will waste a lot of material on testing, but don't give up, you will get there mate ;) if you need anything just drop me a msg. Thanks.

@nichanbalian 6 ай бұрын

Do you have any idea if this tile is fired in a ceramic kiln to 800 C then the black will stay and not burn away? Many thanks in advance

@lightworkz61 6 ай бұрын

Hi & thanks, Hmmm now that a good question my friend, to be honest I have no idea, I do know that I can't scratch it off, I have one I engraved almost 2 years ago, it's been in the dishwasher hundreds of times and still looks just as black, but as for 800c in a kiln I just don't know, sorry.

@mrSanders. 8 ай бұрын

hi, tell me how about the wear resistance of the design, does it wash off or crumble or bake like ceramics?

@lightworkz61 8 ай бұрын

Hi, I have ceramic tiles that I engraved over 1yr ago and they still look the same, I have washed them in the dishwasher hundreds of times and they are still looking good, also the design does not scratch off, I tried with my knife blade, didn't touch it ;) Thanks for the comment.

@mrSanders. 8 ай бұрын

@@lightworkz61 Thanks!!!

@mrSanders. 8 ай бұрын

@@lightworkz61 will this work on MOPA lasers?

@lightworkz61 8 ай бұрын

@mrSanders. yes, I have seen KZfaq vids of people using fiber laser on ceramic with tio2 ;)

@soapmode Жыл бұрын

Will this laser engraver cut 0.5mm sheet brass?

@lightworkz61 Жыл бұрын

Hi, I don't know of any diode laser machines that can cut any metals of a thickness of .5mm, think you better look into fiber cutting lasers ;)

@Garage39GmbH-wr9sd 7 ай бұрын

Шикарно!!!Какой материал?

@lightworkz61 7 ай бұрын

Hi & thanks, I made this on ceramic tile ;)

@pedroreinoso2967 10 ай бұрын

Greetings teacher, how do you prepare Ti02?

@lightworkz61 10 ай бұрын

Hi. OMG I'm no teacher mate, just an ordinary guy playing with lasers ;) OK I mix 3 to 1 ratio, 1 teaspoon tio2 - 3 teaspoons thinners, make sure to mix it well. Don't make more than you need as it will loose it strength and revert back to powder :( I hope this has helped. Thanks for the comment.

@pedroreinoso2967 10 ай бұрын

Thanks

@Skillken 7 ай бұрын

Amazing ! What type of laser do you recommend ? LU2-2 1.6W, LU2-4-SF 5.5W, LU2-4-LF 5.5W, LU2-10A 10W, LU3-20A 20W. What differences would this make, so that I understand correctly.

@lightworkz61 7 ай бұрын

Hi & thanks ;) Ok as for the laser, well I have the LM3 10w and the LM3 LE 20w the LM3 LE is a bit cheaper and to be totally honest it's better than the standard LM3, if you go for the LM2 LE and the 20w module then you don't need the extra control board, as the LE has a newer main board than the LM 3, so I would recommend the LM3 LE + 20w + air assist, please note that the 20w requires an air assist which has to be running every time you use the laser or you will burn out the window lens in less than a month, believe me I know. As for the difference then it all comes down to power, with the 20w you can run jobs faster using lower power settings, as a bonus the dot size on the 20w is finally square and is .08x.08 so you will get more detail in your engravings ;) I hope this has helped you, if you have any questions just drop me a msg here or on FB. Thanks. facebook.com/lightworkz.graphicdesign

@Skillken 7 ай бұрын

@@lightworkz61 Thank you very much for this valuable advice and for the speed of the response. I will do my research on the Ortur website and I will surely come back to you! Thank you again for your kindness :)

@lightworkz61 7 ай бұрын

@@Skillken Your most welcome my friend, if you do decide to go with Ortur, please contact me before you order, I will try and get you some discount on your order ;)

@Skillken 7 ай бұрын

@@lightworkz61 Hi! Thank you for the proposal ;) So, taking into account the budget that I want to devote to it to start and the availability on the Ortur website, I am thinking of moving towards the LM2 Pro S2 with the LU-2-10A module, the air pump and the metal enclosure for laser master 2 pro (expensive but I have a cat and for safety it seems interesting to me. Your opinion on this protection?) Do you think it is a good choice to start with? From a price point of view, with the 15% discount from the newsletter and the new year's promotions, I arrive at a total of $778, delivery costs included. Do you think you can get me a better price? And, for this overall price, do you think I should make my choice differently?

@lightworkz61 7 ай бұрын

@@Skillken Hi mate, ok I would recommend the LM3 LE (much better build quality than the LM2 S2 Pro) with the LU-2-10w module €338.46 get the air pump €118.91 and build a simple but effective wooden enclosed box with lift up top, a 120mm 12v PC fan for smoke extraction and a 30x30cm sheet of orange laser protection acrylic from amazon to fit in the lid, cost for this should be under €60 also simple enough to build ;) total cost would be around €517.37 depending on the price of wood, hinge, acrylic & PC fan where you live. Link to LM3 LE 10w below. ortur.net/en-eu/collections/laser-engraving-machine/products/ortur-laser-master-3-lite?variant=44087286071529 What do you think?

@Eightbitgen Жыл бұрын

How long does it take to make this?

@lightworkz61 Жыл бұрын

HI & thanks, to be honest I never saved that project as I was just playing around, I would guess that at speed=5000 Power=30 Dpi=318 it would take around 25 mins to complete, I hope that this has helped ;)

@Garage39GmbH-wr9sd 7 ай бұрын

Керамика???

@lightworkz61 7 ай бұрын

Hi & thanks. Yes it's ceramic tile.