It was very smart of you to keep the covers on the radiators. Most painters are very careful, but accidents do happen. Your boiler install was magnificent as usual. I hope it's open for display instead of closed up in a cupboard.

Finally some very good Plumber in UK start going to future.. In Hungary we use manifold radiator system for years also hot and cold MLCP.. Very nice job.. 👍

Another interesting vid ... thanks again. Have a great week!

Great video and very interesting all those different materials and fittings. And the bag set up was brilliant. Well done to you and Marcus. You’re be ok if boiler ever breaks down having cold showers lol. Keep the videos coming. Well done again loved the radiator manifold job

Another great video Pete and great idea with the Fluke tray. I’m an electrician and have been eyeing up the 7.5 bag for a while. Looks like the tray will sit in there a treat even with the original lid in place

Great video Pete Billy knows his stuff great talk through 👍🏻

Finally somebody that understands that manifold has nothing to do with underfloor but with plumbing in general. Thanks. This is standard pipework in Italy and all across Europe

Great video Pete. The clips that fit between the joists from Walraven are called Britclips Rapid Sliding Wall Bracket.

That is definitely the best way of installing flow and return to the rads and a very neat installation. An improvement would have been using a set of underfloor manifolds then you could have all lockshield wide open and do system/rad balancing at the manifolds. Useful for future maintenance down the line too. The whole install of boiler/manifolds looked very neat - homeowner must be chuffed.😀👍

Cracking install with that manifold and pipework 👍

Good stuff as usual PB

Man thank you for giving us premium content.

We've done full office blocks in that mlcp. Lay down cable tray under the floor and cable tied the pipe to the tray. It's great stuff and saves so much time on site.

Evening PB plumbing, really great video, love the use of MLCP, the 16x15 socket spigot adaptors increase the number of joints, I work for Valsir and sell the range of MLCP with the opportunity for direct accounts, we do a socket socket 16x15 coupling or a 16x15 rad tail this maybe an option for you…. Great videos 👍

Great video, love the MLPC pipe, seen many alternatives to copper in use here on KZfaq but this pre lagged material is a game changer. Not sure how it fits in the DIY market. I’ve seen the gas pipe in use, when my old bf boiler dies and a condensing boiler is needed, the current 15mm is too small, boiler couldn’t be further away from meter, no cooker now either so it’s a new 22mm along the outside of the house or the flexing used here under the poor access floor. Cost/time will be a serious contender. Keep training with the cold showers.

Great video 👍🏽,did the same system at my sister's house using manifold feeding radiators, Ideal for bigger homes costs a bit more as having to zone each room with stats,but save on running costs as it only sends heat to which room is called for, recommend this for some of our customers too.

Great episode la

Nice work 👌🏼

Looks very efficient piping which balances out the fact that there is a greater proportion of HW in the pipes than a 2 pipe system

Nice job Peter well done mate 👍🏼🙂

Thank you was going to ask you about the pipe cutting tool.

we use those caddy straps ( electrician ) for conduit drops and back boxes in stud walls there a proper time saver on site.

Hi Pete great video the bracket are called Britclips mini rapid sliding wall bracket

we call those caddy brackets here in ontario canada :) great for water lines in a commercial setting

Nice job

Pete, point 2 point is the way forward. The days of copper throughout the property is not viable Mlcp it 😁

Nice vid 👍

Love your videos buddy, even started copying you and had a cold shower, horrible at the time but feel good during the day

🤣🤣🤣the guy at the end piss funny screw it in bareback

We could watch that pipe bending all day mate 🔥

Great video, like the use of the trac pipe. Do you still have a discount code for velocity bags?

Great video Pete, what happened with the auto fill on the boiler you fitted? Did it stop at a certain pressure whilst it was in purging mode.

Great video. I've often wondered why we don't do this more often. I worked with plumber & he did this as standard using UPINOR. Quick question mate. Does the tradify app work alongside quickbooks? Or does it do away with the likes of quickbooks?

Do you have a room stat in every room ? That's the idea of using a ufh manifold for radiators .

Because now you've got 3 couplings underneath a floor any few take to Y tube directly to the floor in your radiator it's one length

I'm using MLCP here in Romania for years now. Got them big diameters also, 32mm, 40mm even 50mm sometimes. I use the same Rems press as you are, tho they're only up to 35mm copper and 40mm mlcp/plastic.

Pete when you gonna design a boiler instead of a bag? 😉 Looking to get some of those little dewalt boxes you use for little bits, where you get them from bud?

How did you find the system eg to pipe up and agree with the bags the brand I use comes in boxes with each wrapped in a little paper tissue bag so everything is recyclable which I think things need to start move that way

I currently do jobbing and light install work, which bag would you recommend? The 3.5 or the 7.0? Don't want to spent a load of money on a bag I might not like

Re: Radiator. Can you press onto chromed copper pipe tails or do you need to sand coating back to bare copper then press?

Nice to see you do some mlcp , it’s the future…. The yellow mlcp is approved for gas in Europe, game changer. If you need more mlcp fittings in the future I can recommend the tweetop brand from natural green heat

We just call them telescopic brackets, us Sparks use them all the time on commercial jobs

I dont recommend using ANY Pushfit fittings on the reducing spigot adaptors. (eg, 16mm MLCP to 15mm Spigot) The tail is too smooth so the internals of a pushfit fitting have nothing to grab onto. More than likely any standard domestic pressure will blow the fitting(s) off. Just be cautious.

Caddy brackets 👌👍

Did you do the heat geek course ? You mentioned it quite a while ago?

Hi Peter which makes radiator you use Regards Faruk

Random question, but were you in hitchin in Hertfordshire this week ...

Whats the benefit of using loctite than ptfe or joint compound?

How much should a proper boiler service cost, full strip and clean, repressurise the expansion vessel ?

10:44 Any particular reason why go from MLCP to Copper again for radiators ? Here in Belgium we use i think for 15-20 years or more Alu-Pex ( from Frankische or Heco and other brands ) On new builds and reno's.. At my house all te MLCP comes out the wall and bends in to the floor ( no floorboards here but tiles and screed ) bend with a spring directly in the radiator block and you don't see any pipework . The extra work and compresson fittings are expensive .. ( as you said you needed 30 mlcp to copper fittings those are not cheap .. and 90 degree copper compression and you need at least 6 crimps per radiator .. if going directly with MLCP to the rad 0 crimps ) . But never the less very nice job . Oh btw the collector is also something we do for radiators and underfloor heating .. So every radiator had is own 2 pipes ( flow and return) to the collecor on evert level of the house .. ofcourse the feed of collector is then with thicker alpex .. or copper ( EXPENSIVE dees days )

Do you need pipe inserts for the MLCP, great video, like the idea of point to point installation, well done on your cold shower routine, rather you than me.

What’s the point of a deareator being fitted when the boiler has an aav, Honest questions as doesn’t make sense to me

you guys must spend a fortune on fittings and pipework. just can't warrant the prices myself

Next time Pete just bring the mlp straight up to the rads through the floor no joints in the floor, most people paint the copper tails white anyway

I just learned a 180⁰ lol xx

16:12 I would run PEX straight to rad so that there are zero joints under the floor and it will never silently leak

Who was the engineer at the end? Interesting video today not used one of them radiator manifolds before either. Tracpipe is a good option to have I often forget I could use this when looking for ways to get the gas pipe places easier.

Hi Pete. Great job! I am wondering why you change from mlcp to copper to supply the radiators instead of directly routing the mlcp into the tcv. You could save any connection under the.floor. Is there any purpose than cosmetic reasons? Regards Stephan

Trying to use your code on power tool mate but never worked PB5

Most people call those metal braces Caddy Straps don’t know if that’s the correct term but that’s all I’ve heard them called.

U could actually buy that manafold with flow meters for better balancing. Difference is 50€

Does this work out very expensive as all press fit fittings are well expensive you must have good prices on your jobs

I like the no joints under the floor, i would never be able to sleep at night, if i knew there was a load of push-fit joints under my floor. While on the subject, I've got 200 metres of layflat pipe, going chaeap if anyones interested. North leicestershire 😉

WHEN DOING BOIKER INSTALL OR REPLACEMENT FIT CARBON MONOXIDE DETECTORS… also when doing annual gas safety checks selling carbons as part of it gives u an extra revenue stream ( after all they only last 5 years(( most of them))

Hello pb I'm a mechanical engineer just like you why didn't you put the MLC pipe directly in the radiatortap?. Ore They are special couplings with koper 15mm to 16,2 tube

Caddy straps!

Hi can anyone help me .. got a “””Broughton HPW40 36kW Portable Electric Boiler (400V) “” sitting in my store . It was purchased for a job then customer cancelled… it’s never been used cost me over £2400 new .. willing to accept offers … any advice on best place to sell this would be gratefully received

Can you use 577 for rad tails?

so you can use 2 hands! Thought you had a missing arm

Completely different topic - I have noticed that you have a good quality thermal camera Fluke. Can you please, please tell me, if you direct it on your bend of the elbow - can you see your veins? This test should not take you longer than 10 seconds....

🤘😎🤘

With the cost of energy soaring. We will all be taking cold showers, and speaking 3 octaves higher jockstraps will be a thing of the past BRR

Bit rough, but I’d give it a pass 😆

Hi Pete have you ever designed a low loss header

Was going to say bender porn but doesn’t sound right so I will say loved the 180 degree. 👍

Wondering if any plumber in and around the derby area could help me out? I paid for a learn while you work plumbing course (NVQ level 2 and 3) finished my level 2 but didn’t do my level 3 as with my normal job and work life it’s hard, plus I can’t seem to put my level 2 skills to practice cause I want to work with a plumber for a little while at weekends if possible to get my experience but can’t ever catch a break so I’ve just given up and carried on with my full time job ever since. I have been watching these videos and it’s given me a itch to get into plumbing. If anyone could help who’s in the industry it would be much appreciated. Probably won’t hear ote but worth dropping the message. Keep up the good videos by the way 👍

Sorry PB, I know this aint ebay

12:45 were in 2022 mate

Why not form bent the 15mm tails to the Radiators Pete?? Also, that Trac Pipe is shite, one wee knock on a fitting & it leaks. I wouldn’t use it mate. Regards Dick Puller👍👍

That’s not a knife 🐊

Not into that trac pipe.

Ohh look gas pipe that is copying LDF-4-50 Coax and connectors

First who cares !