Part 1 of 2 - Delta Faucet Tub Shower Valve Cartridge Replacement Repair 1700 Series RP 32104

No video

Part 1 of 2 - Delta Faucet Tub Shower Valve Cartridge Replacement Repair 1700 Series RP 32104

Рет қаралды 337,600

Loveher The Cute Pug Dog Puppy

Күн бұрын

Delta Faucet Tub Shower Valve Cartridge Replacement Repair 1700 Series RP 32104. Please comment or rate.

Пікірлер: 86

@paulr2389 Ай бұрын

Excellent descriptive video. Thanks! I wish I'd seen this before calling a plumber who replaced the whole fixture for many $$$. But, if one has time, the key issue is de-liming (calcium, etc.) which can be done, as you say with CLR, but I've used strong vinegar for the same result (well, after a number of hours). One word of advice would be to use a LOT of silicone grease on all flexible parts like ALL the "0" rings once the metal parts are really smooth and clear of deposits. That's why plumbers are not really interested in the cleaning, so they'll just cut and replace the whole unit. Again, well-done for a full discussion!

@adimadau9431 Жыл бұрын

I just completed my Delta faucet replacement following this excellent video. Very well done. My replacement had a few difficulties, the brass ring was calcified on and I had to use WD40 to break the calcification. The two rubber grommets with the spring was more challenging to replace. I used a phillip screwdriver to insert it. Just took more time than on the video. Finally, locating the screws for the cover plate was more difficult than on the video. In the end, I saved at least $150 doing it myself. Thanks.

@adimadau9431 Жыл бұрын

BTW, Delta warrants their cartridges for life, call them and they will send you one at no cost. This is the 3rd cartridge I replaced where Delta gave it to me for free.

@PointLookoutResident 5 жыл бұрын

Not only did you save me a call to a plumber, but it turned out I didn't need any new parts, so you saved me $50.00 for a new cartridge! Thank you for you video

@baaustin11 5 жыл бұрын

Delta faucets etc, are guaranteed for life! Just call them and be insistent. I have called many times and they have sent out repair kits each time. Once when the faucet had been discontinued they offered me a great deal on a NEW faucet, I said no and then he sent the new faucet for FREE. Yes free, they could not replace the parts so they had to send me a new one. Once when they gave me a hard time so I waited and called back a few weeks later and then another person gave me what I wanted. Just ask.

@hondapilot 4 жыл бұрын

Superb instructions. Real hard work by the presenter going over each step and precautions. Very helpful. Recomend following each tip and caution. Cannot go wrong. Had the wife help with the laptop. No fuss, argument and no blood spilled. 😅

@phukka_feelings 2 жыл бұрын

Thank you!!! has same one and video made it super easy to fix! Another Big tip! prepare for that brass bonnet nut to be seized, we had to run to Home Depot and got a Husky Strap Wrench for like 10 bucks, and it took that nut off no problem at all!! Great tool! Thanks again!

@lahirisangrami 8 жыл бұрын

The best presentation on Replacement of Delta Faucet Tub Shower Valve Cartridge in the United States. The gentleman is amazingly patient, organized and professional (a kind of perfectionist) who slowly took us through every step explaining every details that may appear trifling to some but, he is immensely helpful... a model Presenter or maybe an Angel in disguise, I think !!! He is even better than the professional from Delta who explained the stuff "How To Replace a Delta Tub or Shower Cartridge" in another video here. I know I can't thank you enough...

@loveherthecutepugdogpuppy1707 8 жыл бұрын

Thanks for those very kind words. !!!!!!!!

@rpyka1 7 жыл бұрын

This is a superb video set. Thank you very much for creating and posting. It was extremely useful - after viewing, I successfully replaced the cartridge and seals in my own Delta shower faucet, thus fixing a long-time leak.

@loveherthecutepugdogpuppy1707 7 жыл бұрын

rpyka1 thanks for watching. Did you see my note about setting the temperature stop? Have a nice day!

@rpyka1 7 жыл бұрын

This was the one note that surprised me in your video. You noted at 7:54 in Part 2 of your video set that the exact position doesn't matter, where in actuality it does. The position of the stop limit on the plastic insert (the thing you didn't have a name for - and I don't either) relative to the stop limit in the ON/OFF knob is what determines the maximum temperature. Increasing the distance between the two limit stops (counter-clockwise of the insert with respect to ON/OFF knob) will increase the maximum temperature. Unfortunately this position (too hot or not hot enough) is something that needs to be determined by trial and error. I feel this probably should have been explained a bit more in your video. In my case, the insert remained inside the large ON/OFF knob, so the re-clocking was not an issue. Otherwise everything in your videos was very concise and informative. Thanks again for posting. Have a great day too!

@codyq0987 8 жыл бұрын

Thank you very much for the tutorial. One of the best one for repair delta faucet on KZfaq.

@pjjones4234 4 жыл бұрын

Replacing my Delta two in one today. Watched a few videos of this replacement and this was by far the best! Clear, detailed, thorough, great pictures, well-described, it taught me how to get the job done. Thank you!

@zyepod 7 жыл бұрын

I've got a 1700 series cartridge that I thought needed changing and my luck the local hardware store didn't have one and it was to late to go anywhere else. Grasping I decided to change the washers leaked leaked... Desperation got me on the internet where I found your video with yep the same cartridge as mine (watched several that were a different series). After watching you explain how the washers with the springs went I realized I had installed mine incorrectly. Went back in reinstalled them correctly and put a little silicone grease on them and the other double washers that are connected together and no leaks. Luckily I didn't have to replace the cartridge... Thanks for taking the time to share the video.

@JamesDenginWPG 6 жыл бұрын

Just replaced a Delta Monitor shower faucet. This video is of great help. Thanks!

@voice4voicelessKrzysiek 8 жыл бұрын

Very nicely and professionally done, easy to follow. Thank you very much, it allowed me to do replacement flawlessly.

@Jessica-ov4dj 2 жыл бұрын

Thank you for this! I feel so stupid - I was having trouble reconnecting the temperature dial to the handle after it came off (I kept trying to twist it back on). Didn't realize the top piece popped off to reveal the top of the screw.

@danmeier4030 9 жыл бұрын

Nice instructional video, The required information is very systematically and thoughtfully presented.

@baukerman1000 5 жыл бұрын

Wow!! What an awesome video. I so appreciate the in depth detail. Exactly what I needed to do my own repairs. Thank You!

@sherrik6546 7 жыл бұрын

Thank you for this very helpful tutorial! My husband and I were able to replace the cartridge in my dad's shower for him easily.

@barjan99 4 жыл бұрын

Great video and though my faucet was a bit older this really helped me with the parts.

@larrywebber7654 5 жыл бұрын

That was awesome. To the point. Clear. Well videoed. Thank you so much!

@baaustin11 5 жыл бұрын

@louisbraud8213 4 жыл бұрын

Easy to understand, good discussion of key points. Thanks

@bobbybrooner 6 жыл бұрын

You made it easy to fix the leak! Thank you very much!

@mkeaspen 7 жыл бұрын

Thanks, very helpful tip on the cleaning with CLR.

@aaal123able 5 жыл бұрын

Just wanted to say thanks. Your video helped me out a lot.

@johnranalletta9249 6 жыл бұрын

thanks. just made my change out a lot easier. Also, check pricing. Most supply houses want $80+ for this valve. Got from Amazon for

@adimadau9431 Жыл бұрын

Delta has a lifetime warranty on their faucets. Call them and they will send you the cartridge for free.

@mardighakimian5472 2 жыл бұрын

Your pretty smart to notice the plastic

@codyq0987 7 жыл бұрын

Thanks again for this great tutorial and save me time and money!

@sharkbait42010 5 жыл бұрын

Very helpful. My shower is now fixed.

@pooriashams 9 жыл бұрын

The position of that geary thing matters. It sets the peak hot mix

@loveherthecutepugdogpuppy1707 8 жыл бұрын

You are right. I discovered that afterwards. It's easy to adjust after the first screw is removed. Thanks for explaining.

@deanwill14 7 жыл бұрын

if got a small leak coming from the shower head any idea on how to fix it

@webpuddin 9 жыл бұрын

I wasn't sure how to get the 'cap' off ... the manual says to 'snap' it into place, but wasn't sure if it simply 'snapped' back off or if you had to somehow press something, twist a certain way ... or whatever. I watched this - & then simply 'snapped' mine right off perfectly! thanks!

@MrNewmanRay 6 жыл бұрын

Thanks for posting this, it was very heplful i have the same exact delta 1700 was nice to see someone doing it so i dindnt have to wing it.

@buddy7277 4 жыл бұрын

I really appreciate you making this video, ty so much

@BigSFun 3 жыл бұрын

Thanks this video helped me a ton!!

@PugFaceMedia 7 жыл бұрын

Great video! Saved me a call to a plumber!

@terrycalof8403 2 жыл бұрын

I would not recommend CLR be used to remove scale in your case. CLR has specific instructions to not be used on brass. The body of the faucet that holds the cartridge is made of brass. I would use white undiluted household vinegar instead.

@rainerrain9689 2 жыл бұрын

Can I use Liquid Plummer Gel and dab it on and brush away the mineral deposits ? Thanks.

@mjdu38 5 жыл бұрын

This video was the most helpful.

@PHBeagle 10 жыл бұрын

Thank you. Very helpful and easy to understand.

@michelgagne608 5 жыл бұрын

Thank you very much for your help.

@timb2294 3 жыл бұрын

Great Job! Thank you

@JuanASanchezSr 2 жыл бұрын

Great video thank you

@valb7518 8 жыл бұрын

Excellent video. Very helpful! Thank you.

@dimejotape 7 жыл бұрын

Thank you for the detailed video. As I was placing the new spring and washer, a stream of water kept coming out. Intense at the beginning but has continued. Any advice!?

@mvp2628 3 жыл бұрын

Thank you!

@veenagupta3877 2 жыл бұрын

Thanks

@lanjian45 4 жыл бұрын

Thanks, it's very helpful!

@HelpMeOutVideos 6 жыл бұрын

Very helpful. Thank you!

@FINfinFINfinFINfin 3 жыл бұрын

Thanks man!

@weirdfishweirdfish6636 5 жыл бұрын

Heads up diy guys n girls do not use pipe wrench on the bonnet if has any corrosion will be a little tight and you will bend the bonnet and changing a valve

@goblue7100 4 жыл бұрын

Is it possible to change the cartridge I'd like a single handle that goes to hot and cold without the little knob in front. My teeth are completely stripped and needs replacing anyway was just wondering

@HH-yc7oz 4 жыл бұрын

why is your "hot side" facing up? Isn't it supposed to face left per the installation guide? I'm having an argument with my contractor who installed it "hot side" up and my water won't run until the volume control is turned to the halfway point when looking at my trim plate.

@z28punisher42 7 жыл бұрын

eyes staring at you. lol I swear that's exactly what I was thinking

@hgfokaa 9 жыл бұрын

i just replaced a cartridge on my shower faucet which is a 1700 series. I used a plier to remove the metal brass ring ( i think its also called a bonnet nut) because it was too tight. Now when I put the new cartridge in it doesn't snap in properly. so of course it keeps leaking and when you turn the handle, the cartridge also turns. Any suggestion? do you thing I damaged the threads on the metal ring by pulling it out forcefully ? .

@symphx1 10 жыл бұрын

Hi my plumber installed my new dual handle faucet. I cant turn the temp. adjust at all, Ive removed the cap and the screw and it wont turn that white cartridge nubbin at all. I dont want to force it, why wont it turn? (Im going away from the limit block dont worry)

@okaythen001 8 жыл бұрын

I got delta monitor 1400 any idea what's the allen wrench size? it's leaking from the showerhead. thanks for the helpful vid (delta faucets allen wrench are 3/32 right?)

@joeystein6001 7 жыл бұрын

The brass ring around the cartridge is stuck.... No luck with pipe wrench. No luck with WD - 40. Any suggestions??

@jonathangrindstaff4619 6 жыл бұрын

Joey Stein cut it off and replace for $6. This won't help you Joey since you probably figured it out but just in case anybody else needs this.

@jonathangrindstaff4619 6 жыл бұрын

It can be found by searching 1700 delta bonnet nut

@yc30337 6 жыл бұрын

Lots of liquid wrench (the penetrant type), and rubber strap wrench helped me to get my old brass ring out.

@rudyossanchez 5 жыл бұрын

Don't force it. I managed to sheer mind clean off .😐

@otonielvargas5720 5 жыл бұрын

Camisones para infantiles

@user-gi2rc1xq4x 6 жыл бұрын

Классное видео давайте дружить каналами

@someguywithatophat7599 7 жыл бұрын

why cant i find one that actually shows how mine looks on the inside . i have a wate adjust handle and a temperature adjust and on the inside there are four ears on the cartridge metal cover

@raulgutierrez5920 4 жыл бұрын

Most of the time is hard to remove the o ring? Why you don't show how?🤔

@bkvike Жыл бұрын

Edit, then ok that wasn't tight at all. Not a chance.

@utubeviewer22 6 жыл бұрын

Bad luck for me. The brass ring was stuck and even in an slow attempt to open it, the entire body twisted, and broke the pipe. Be careful in opening the cap.

@raulgutierrez5920 4 жыл бұрын

If you put W40 around the ring and wait little time and use two channel Locks med and bigs then you good🤔👍

@darkegress4392 2 жыл бұрын

PIPE WRENCH

@raulgutierrez5920 4 жыл бұрын

!Why people want to be aplumber in videos but they not!!!🤣🤣🤣😂

@raulgutierrez5920 4 жыл бұрын

You wrong buddy you put W40 wait little time and then use channel locks medium and bigs l used to be apts maint🤔🤔

@SuaveCityGear 4 жыл бұрын

I don’t see YOU making a video, be quiet...it helped me, and I’m a lawyer.

@darkegress4392 2 жыл бұрын

Pipe wrench is the ONLY way to go.