Honda CRF450R Swingarm Bearing Replacement | Honda CRF450-R Rebuild Part 9

Honda CRF450R Swingarm Bearing Replacement | Honda CRF450-R Rebuild Part 9 | Partzilla.com

Рет қаралды 11,955

2 жыл бұрын

Pivot Works CRF450 swingarm bearing kit: www.partzilla.com/catalog-pro...
See how to replace the swingarm bearings on a CRF450R in this video from Partzilla.com. This is part of a larger rebuild project where rebuilding this dirt bike from the ground up. See more of the rebuild here: • Honda CRF 450R Repairs
The rear end of this dirt bike was in dire need of work. We’ve already tackled the shock linkage bearings, and here we’ll replace the swingarm bearings on our CRF450R. You’ll notice we have the engine out here, but that’s not necessary to do this job.
We’ll start with the shock. We’ll get it disconnected and removed and then we’ll move down to the shock pivot. From there, we’ll work on getting everything disconnected to remove the swingarm.
The swingarm bearings are actually several pieces: seals, washers, and the bearings themselves. You want to make sure each piece is greased before you install them. We’ll show you how to press them into place.
A Motion Pro suspension bearing tool set is nearly a must for this job. See how it works in the video and get your here: www.partzilla.com/catalog-pro...
See the rear swingarm diagram here: www.partzilla.com/catalog/hon...
Read how to do this job step by step: www.partzilla.com/blog/honda/...
Watch us remove the engine on our Honda CFR450 here: • Honda CRF450 Engine Re...
See the CRF450 engine teardown here: • Honda CRF450 Engine Te...
VIDEO HIGHLIGHTS:
Removing the shock - 1:37
Removing the shock pivot - 2:20
Removing the rear brakes - 3:00
Removing the rear wheel - 3:40
Removing the swingarm - 4:20
Removing the old bearings - 5:00
Using the Motion Pro suspension tool - 6:20
Installing new bearings - 8:00
Shop for OEM Honda motorcycle parts here: www.partzilla.com/catalog/hon...
Talk to us:
Twitter: / partzilla
Facebook: / partzilla
Instagram: / partzilla
In the video we’re working with a 2005 Honda CRF450R, but you may have similar steps for your Honda dirt bike. If you’re not sure whether these steps apply to your machine, leave a comment and we’ll get back to you.

Пікірлер: 15

@caseyjones466 3 ай бұрын

All these videos couldn't be better. Amazing quality camera, amazing editing, and best of all you explain everything in PERFECT detail BOTH disassembling AND reassembling every piece. Because of this, you have a subscriber and a customer.

@gazvlogs7459 Жыл бұрын

7:39 Challenge accepted. Threw the needle bearings in the freezer overnight and heated up the swing arm with a blowtorch. It slid in like a hot dog flying through a hallway.

@williamevans6468 2 жыл бұрын

Nice video for people that are learning how to do this job. Personally, I have done this job dozens of times and have always used a 21mm socket, all thread, washers and nuts and have never had an issue doing it correctly. But if you are new to doing this sort of stuff and don't have a ton of experience on making sure everything is just right then it is best to purchase the tool or pay to get it done by a professional.

@RichM1983 2 жыл бұрын

I'm 37 and worked on bikes my whole life and never knew about the screw driver lol. Love your videos!

@crf450xripper 2 жыл бұрын

Excellent video. I really enjoyed the pace of the material and camera shots. Thank you for sharing.

@potanda 4 ай бұрын

Thank you for taking your time to make this video it really helped me 👍

@chrisheath7500 Жыл бұрын

Very nice. I had to do mine and they were so bad I had no idea which bearings went where. Thanks again.

@selvamrangasamy5666 2 жыл бұрын

Every one video of Partzilla I have like it and viewing interest so much- Thank s

@yeisonalexanderrodriguezli1407 2 жыл бұрын

Hi from Colombia I love your videos and of course I really love motorcycles

@chiquitovlogs 9 ай бұрын

2008-2009 Honda CRF 250R Bike transmission Bearing Kit?

@MrBIGJOHNJOHNSON1 Жыл бұрын

What part number is that motion pro bearing kit?

@PartzillaParts Жыл бұрын

Rigth here: www.partzilla.com/catalog-product/collection/F79109E83B4E09698834E329695FC76FA774B0F3/C90D1F7FA07E63BBA06E356391FC8876EBADD7F1

@oceeydiA 2 жыл бұрын

@andrewpereira1117 Жыл бұрын

I would've used a ratchet.. brrrr

@boone7777777777 4 ай бұрын

Here i did the stem race and the swing arm bearings with a hammer and sockets. It's pretty easy honestly: kzfaq.info/get/bejne/r86BhZtoya3Jqas.htmlsi=wOOqgXCppG9XQIVo